2008 MERCEDES-BENZ SL550 stop start

338 Operation
Vehicle care
Fold the wiper arms forward until they
snap into place.
Clean the wiper blade inserts with a
clean cloth and detergent solution.
Use a soft, clean cloth and a mild win-
dow cleaning solution on all outside
and inside glass surfaces.
An automotive glass cleaner is recom-
mended.Rear window cleaning
Clean the rear window with the hardtop
fully raised and closed.
Use a soft, clean cloth and a mild win-
dow cleaning solution on all outside
and inside glass surfaces.
An automotive glass cleaner is recom-
mended.
Light alloy wheels
If possible, clean wheels once a week.
Use Mercedes-Benz approved Wheel
Care, a soft bristle brush and a strong
spray of water for cleaning the light al-
loy wheels.
Warning!G
For safety reasons, switch off wipers and re-
move SmartKey from starter switch (vehi-
cles with KEYLESS-GO*: Make sure the
vehicle’s on-board electronics have
status0.) before cleaning the windshield
and/or the wiper blades. Otherwise, the
wiper motor could suddenly turn on and
cause injury.
!Do not pull on the wiper blade inserts. They
could tear.
!Fold the windshield wiper arms back onto
the windshield before turning the SmartKey in
the starter switch or pressing the KEYLESS-GO
start/stop button (vehicles with KEYLESS-GO*).
Hold on to the wiper when folding the wiper arm
back. If released, the force of the impact from
the tensioning spring could crack the windshield.
!To clean the window interior, do not use a
dry cloth, abrasives, solvents or cleaners con-
taining solvents. Do not touch the inside of the
front, rear or side windows with hard objects
such as an ice scraper or ring. Doing so may
damage the windows.
Warning!G
Do not clean the rear window with the hard-
top in a position other than the fully raised
and closed position. Otherwise, the hardtop
may move unexpectedly which may result in
personal injury to you or others.
!Only use acid-free cleaning materials. Acid
may cause corrosion or damage the clear coat.


352 Practical hints
What to do if …
ProblemPossible cause/consequenceSuggested solution
on for a maximum of 6 seconds
after starting the engine.The seat belt telltale reminds you and your
passenger to fasten your seat belts before
driving off.Fasten your seat belts.
Regardless of whether the seat belts
are fastened or not, the seat belt tell-
tale always comes on and remains lit
for 6 seconds after starting the en-
gine.
maximum of 6 seconds after
starting the engine.You have forgotten to fasten your seat belt.Fasten your seat belt.
The warning chime stops sounding.
on while the vehicle is standing
still and the engine is running or
during driving.You and/or your passenger have forgotten to
fasten your seat belts.Fasten your seat belts.
The seat belt telltale goes out.
There are items placed on the passenger seat
and therefore the system senses the passen-
ger seat as being occupied.Remove the items from the passenger
seat and put them in a safe place.
The seat belt telltale goes out.

356 Practical hints
What to do if …
Warning!G
Each tire, including the spare (if provided),
should be checked monthly when cold and
inflated to the inflation pressure recom-
mended by the vehicle manufacturer on the
Tire and Loading Information placard on the
driver’s door B-pillar (
page 294) or, if
available, the tire inflation pressure label on
the inside of the fuel filler flap (
page 279).
If your vehicle has tires of a different size
than the size indicated on the Tire and Load-
ing Information placard or, if available, the
tire inflation pressure label, you should de-
termine the proper tire inflation pressure for
those tires.
As an added safety feature, your vehicle has
been equipped with a tire pressure monitor-
ing system (TPMS) that illuminates a low tire
pressure telltale when one or more of your
tires is significantly underinflated.
Accordingly, when the low tire pressure tell-
tale illuminates, you should stop and check
your tires as soon as possible, and inflate
them to the proper pressure. Driving on a
significantly underinflated tire causes the
tire to overheat and can lead to tire failure.
Underinflation also reduces fuel efficiency
and tire tread life, and may affect the vehi-
cle’s handling and stopping ability. Please
note that the TPMS is not a substitute for
proper tire maintenance, and it is the driv-
er’s responsibility to maintain correct tire
pressure, even if underinflation has not
reached the level to trigger illumination of
the TPMS low tire pressure telltale.USA only:
Your vehicle has also been equipped with a
TPMS malfunction indicator to indicate
when the system is not operating properly.
The TPMS malfunction indicator is com-
bined with the low tire pressure telltale.
When the system detects a malfunction, the
telltale will flash for approximately
one minute and then remain continuously
illuminated. This sequence will continue
upon subsequent vehicle start-ups as long
as the malfunction exists. When the mal-
function indicator is illuminated, the system
may not be able to detect or signal low tire
pressure as intended.
TPMS malfunctions may occur for a variety
of reasons, including the installation of
replacement or alternate tires or wheels on
the vehicle that prevent the TPMS from
functioning properly. Always check the
TPMS malfunction telltale after replacing
one or more tires or wheels on your vehicle
to ensure that the replacement or alternate
tires and wheels allow the TPMS to continue
to function properly.

361 Practical hints
What to do if …
Text messages
Left displayRight displayPossible cause/consequencePossible solution
Check tires,
then restart
Run Flat Indicator
.
There was a warning message about a
loss in the tire inflation pressure and
the Run Flat Indicator has not been
restarted yet.Make sure that the correct tire inflation
pressure is set for each tire.
Then restart the Run Flat Indicator.
Tire Pressure
Check TiresThe Run Flat Indicator indicates that
the pressure is too low in one or more
tires.Carefully bring the vehicle to a halt, avoid-
ing abrupt steering and braking maneu-
vers. Observe the traffic situation around
you.
Check and adjust tire inflation pressure as
required (
page 302).
If necessary, change the wheel
(
page 417).
Restart the Run Flat Indicator after adjust-
ing the tire inflation pressure values
(
page 304).
ABCMalfunction
Stop CarYou have started driving although the
vehicle level is still too low.
The vehicle is being raised. The ABC
message goes out after a few seconds.Stop your vehicle in a safe location or as
soon as it is safe to do so.
Wait until the message disappears from
the multifunction display.
You may then drive off.

372 Practical hints
What to do if …
Left displayRight displayPossible cause/consequencePossible solution
PGear Selector
Lever To PYou have tried to start the engine with
the KEYLESS-GO* start/stop button
with the gear selector lever not in
position P.Place the gear selector lever in position P.
You have tried to turn off the engine
with the KEYLESS-GO* start/stop
button with the gear selector lever not
in position P.
Run Flat IndicatorInoperativeThe Run Flat Indicator is
malfunctioning.Have the Run Flat Indicator checked by an
authorized Mercedes-Benz Center.
The Run Flat Indicator has been
switched off due to an error.

377 Practical hints
What to do if …
Left displayRight displayPossible cause/consequencePossible solution
# Battery/
Alternator
Stop CarThe battery is malfunctioning.
The electro-hydraulic brake system
requires electrical energy and
therefore has only limited opera-
tion. Considerably greater brake
pedal force is required and the stop-
ping distance is increased.Stop the vehicle in a safe location.
Adjust driving to be consistent with reduced
braking responsiveness.
Contact an authorized Mercedes-Benz
Center.
USA only:
;
Canada only:
3
Reduced
Brake Effect
Start EngineThe battery has insufficient voltage
and cannot supply sufficient power
to the electro-hydraulic brake sys-
tem.Start the engine.
The message disappears when sufficient
voltage is available.
Warning!G
Inhalation of exhaust gas is hazardous to
your health. All exhaust gas contains carbon
monoxide (CO), and inhaling it can cause
unconsciousness and lead to death. Do not
run the engine in confined areas (such as a
garage) which are not properly ventilated.

380 Practical hints
What to do if …
Left displayRight displayPossible cause/consequencePossible solution
2 Brake WearThe brake pads have reached their
wear limit.Have the brake pads replaced as soon as pos-
sible.
Warning!G
Have brake pad replacement and other work
on the electro-hydraulic brake system
carried out by qualified technicians only.
Contact an authorized Mercedes-Benz
Center for further information.
The electro-hydraulic brake system must be
deactivated prior to working on the system.
High pressure is intermittently built up in the
system as part of its automatic self-test.
In addition, the system is automatically
activated when the vehicle is unlocked by
remote control, when the driver or passen-
ger door is opened, when the SmartKey in
the starter switch is turned to position1 or
the KEYLESS-GO* start/stop button is
pressed once, when the brake pedal
is depressed or when the parking brake is
released. Failure to deactivate the system
prior to maintenance will cause brake pis-
tons to extend and brake fluid to leak, which
may result in injuries (contusions and acid
burns). Extended brake pistons may also
cause injury.!Brake pad thickness must be visually
checked by a qualified technician at the intervals
specified in the Maintenance Booklet.

383 Practical hints
What to do if …
Left displayRight displayPossible cause/consequencePossible solution
•Coolant
Stop car,

switch engine off.
The coolant is too hot.
Among other possible causes, the
poly-V-belt could be broken.Stop the vehicle in a safe location or as soon
as it is safe to do so.
Turn off the engine.
Check the poly-V-belt.
If it is broken:
Do not continue to drive. Otherwise, the
engine will overheat due to an inoperative
water pump which may result in damage to
the engine. Contact an authorized
Mercedes-Benz Center.
If it is intact:
Wait for the message to disappear before
restarting the engine.
Doing otherwise could result in serious engine
damage that is not covered by the
Mercedes-Benz Limited Warranty.
(Continued on next page)