2008 MERCEDES-BENZ S63AMG run flat

25 At a glance
Exterior view
ItemPage
1Trunk

Unlocking

Opening and closing

Minispare wheel

Vehicle tool kit
479
479
686
668
2Rear lamps679
3Rear window, defrosting473
4Fuel filler flap
Gasoline538
729
5Doors

Locking and unlocking

Opening and closing
332
332
ItemPage
6Exterior rear view mirror
Parking position361
364
7Towing the vehicle700
8Rims and tires

Checking tire inflation
pressure

Minispare wheel

Flat tire
718
560
670
686
9Hood, opening
Engine oil
Coolant541
543
547
ItemPage
aHeadlamp cleaning system375
bFront lamps679
cWindshield wipers
Wiper blades, replacing
Wiper blades, cleaning381
684
592
dWindow, cleaning592
eRoofs

Power tilt/sliding sunroof

Panorama roof with power
tilt/sliding panel*
486
489

267 Control systems
Instrument cluster control system
Telephone* (page 276)Assistance* (page 279)Service (page 280)Settings (page 281)
Commands/submenus
Dialing a number from the
phone bookDisplaying the distance graph-
ic*, DISTRONIC Plus*
(USA only)Calling up vehicle malfunction,
warning and system status
messages stored in memorySetting daytime running lamp
mode (USA only)
RedialingActivating/deactivating
PRE-SAFE® Brake* (USA only)
Checking tire inflation pres-
sureSwitching additional speedome-
ter on or off
Answering a callSwitching on the Dynamic
Rear View Monitor*
automaticallyCalling up maintenance ser-
vice displaySwitching radar sensors* on or
off (USA only)
Ending a call or rejecting an in-
coming callChecking engine oil level*

280 Control systems
Instrument cluster control system
Press % or $ to select the
“Rearview camera” function.
Press #.
Press # again if you would like to
change the current status.
The following settings are available:
Service menu
The “Service” menu is used for

calling up messages

checking tire inflation pressure elec-
tronically with the Advanced TPMS*
(standard on U.S. vehicles)

activating Run Flat Indicator
(Canada only)

calling up the maintenance service in-
dicator display

check engine oil level*
Calling up vehicle malfunction, warning
and system status messages stored in
memory
Use the vehicle status message memory
menu to scan malfunction and warning
messages that may be stored in the sys-
tem. Such messages appear in the multi-function display and are based on
conditions or system status the vehicle’s
system has recorded.
The vehicle status message memory menu
only appears if there are any messages
stored.
Press ( or & to select the
“Service” menu.
“On when in
Reverse”The Dynamic Rear View
Monitor automatically
switches on when reverse
gear is engaged.
“OFF”The Dynamic Rear View
Monitor is not switched on.
iThe menu overview can be found on
(
page 266).
Warning!G
Malfunction and warning messages are only
indicated for certain systems and are inten-
tionally not very detailed. The malfunction
and warning messages are simply a remind-
er with respect to the operation of certain
systems and do not replace the owner’s
and/or driver’s responsibility to maintain
the vehicle’s operating safety by having all
required maintenance and safety checks
performed on the vehicle and by bringing
the vehicle to an authorized Mercedes-Benz
Center to address the malfunction and
warning messages (
page 612).


281 Control systems
Instrument cluster control system
If conditions have occurred causing
status messages to be recorded, the
number of messages appears in the
multifunction display: “2 Messages”.
Press % or $ to select the mes-
sage.
Press # to confirm.
Checking tire inflation pressure
For information about checking tire infla-
tion pressure (
page 561).
Activating Run Flat Indicator
(Canada only)
For information about activating Run Flat
Indicator (
page 565).Calling up the maintenance service in-
dicator display
For information about calling up the main-
tenance service indicator display
(
page 582).
Checking engine oil level (S 600 and
S65AMG)
For information about checking engine oil
level (
page 543).
Settings menu
In the “Settings” menu, you can:

switch the daytime running lamps on or
off (USA only)

switch the additional speedometer on
or off

switch the radar sensors* on or off
(USA only)Setting daytime running lamp mode
(USA only)
Press ( or & to select the “Set-
tings” menu.
Press % or $ to select the “Day-
time driving lamps” function.
Press #.
Press # again if you would like to
change the current status.
Depending on the previous status, the
daytime running lamps will be switched
on or off.
iSee the “Practical hints” section for mal-
function and warning messages (
page 612).
iIf you turn the SmartKey in the starter
switch to position0 and then back to position2,
all messages will be deleted from the message
memory.
iThe menu overview can be found on
(
page 266).
iThis function is not available in countries
where the daytime running lamp mode is manda-
tory and therefore in a constant mode.

480 Controls in detail
Trunk
Vehicles with trunk opening/closing
system*
1Remote trunk opening/closing* switch
Press and hold switch1 until the
trunk is opened.
The indicator lamp in switch1 comes
on and remains lit until the trunk is
closed.
To interrupt the opening procedure:
Release switch1.Trunk opening-height restriction*
Vehicles with trunk opening/closing sys-
tem*:
The trunk lid opening height can be limited
when transporting goods on a roof rack
(e.g. presence of an optional MB sport lug-
gage container). When activated, the trunk
opens to approximately the height of the
roof edge.
Activate the limiting opening height of
trunk lid using the COMAND system
(
page 249).
Closing trunkClosing trunk from outside manually
1Handles
Lower trunk lid by pulling firmly on
handles1.
Close the trunk with hands placed flat
on the trunk lid.
The power closing assist automatically en-
sures that the trunk lid is pulled closed
completely (
page 342).
iDo not place the SmartKey in the open
trunk. You may lock yourself out.
iIf the vehicle was previously centrally
locked, the trunk will lock automatically after
closing it. All turn signal lamps flash three times
to confirm locking.
Vehicles with KEYLESS-GO*: To prevent a possi-
ble inadvertent lockout, the trunk will open auto-
matically if a SmartKey with KEYLESS-GO* is
recognized inside the vehicle or in the trunk. The vehicle is only locked when the turn signals
flash three times. If you are carrying a second
SmartKey with KEYLESS-GO* with you, you can
still lock the vehicle.

527 Operation
Driving instructions
Driving instructions
Drive sensibly – save fuel
Fuel consumption, to a great extent,
depends on driving habits and operating
conditions.
To save fuel you should:

Keep tires at the recommended tire
inflation pressures.

Remove unnecessary loads.

Remove roof rack when not in use.

Allow engine to warm up under low
load use.

Avoid frequent acceleration and decel-
eration.

Have all maintenance work performed
at the intervals specified in the Mainte-
nance Booklet and as required by the
Maintenance System. Contact an au-
thorized Mercedes-Benz Center.
Fuel consumption is also increased by driv-
ing in cold weather, in stop-and-go traffic,
on short trips, and in hilly area.
Drinking and drivingPedals
Power assistance
Warning!G
Drinking and driving and/or taking drugs
and driving are very dangerous combina-
tions. Even a small amount of alcohol or
drugs can affect your reflexes, perceptions
and judgment.
The possibility of a serious or even fatal ac-
cident are greatly increased when you drink
or take drugs and drive.
Do not drink or take drugs and drive or allow
anyone to drive who has been drinking or
taking drugs.
Warning!G
Make sure that absolutely no objects are ob-
structing the pedals’ range of movement.
Keep the driver’s footwell clear of all obsta-
cles. If there are any floormats or carpets in
the footwell, make sure the pedals still have
sufficient clearance. Otherwise this could
lead to accidents or injury.
Warning!G
With the engine not running, there is no
power assistance for the brake and steering
systems. In this case, it is important to keep
in mind that a considerably higher degree of
effort is necessary to brake and steer the ve-
hicle.

565 Operation
Tires and wheels
Run Flat Indicator (Canada only)
While the vehicle is being driven, the Run
Flat Indicator monitors the set tire inflation
pressures by evaluating each wheel’s rota-
tional speed. This allows the system to de-
tect a significant loss of pressure in a tire.
If a wheel’s rotational speed changes due
to falling tire inflation pressure, you will
see a corresponding warning message in
the multifunction display.
The Run Flat Indicator may function in a re-
stricted manner or with a delay if:

snow chains are mounted to the
vehicle

in presence of ice and snow

you are driving on a loose surface (e.g.
sand or gravel)

you are driving in a very sporty manner
(involving rapid acceleration or high
speeds in curves)
Warning!G
When the multifunction display shows the
message “Tire pressure Check tires”, one or
more of your tires is significantly under-in-
flated. You should stop and check your tires
as soon as possible, and inflate them to the
proper tire inflation pressure as indicated on
the vehicle’s tire information placard. Driv-
ing on a significantly underinflated tire caus-
es the tire to overheat and can lead to tire
failure. Underinflation also reduces fuel effi-
ciency and tire tread life, and may affect the
vehicle’s handling and stopping ability. Each
tire, including the spare, should be checked
monthly when cold and set to the tire infla-
tion pressure recommended by the vehicle
manufacturer on the vehicle placard or the
tire inflation pressure label.
Warning!G
The Run Flat Indicator does not provide a
warning for wrongly selected tire inflation
pressures. Always adjust tire inflation pres-
sure according to the placard on the driver’s
door B-pillar or fuel filler flap.
The Run Flat Indicator does not replace reg-
ular checks of the tire inflation pressures
since a gradual pressure loss in more than
one tire cannot be detected by the Run Flat
Indicator.
The Run Flat Indicator is not able to issue a
warning due to a sudden dramatic loss of
tire inflation pressure (e.g. tire blowout
caused by a foreign object). In this case
bring the vehicle to a halt by carefully apply-
ing the brakes and avoiding abrupt steering
maneuvers.

566 Operation
Tires and wheels
Reactivating the Run Flat Indicator
The tire inflation pressure monitor must be
reactivated in the following situations:

If you have changed the tire inflation
pressure

If you have replaced the wheels or tires

If you have installed new wheels or
tires
Using the tire placard on the driver’s
door B-pillar (
page 553) or, if avail-
able, the inside of the fuel filler flap
(
page 538), make sure the tire infla-
tion pressure of all four tires is correct.
Switch on the ignition (page 344).
Press( or& to select the menu
“Service”.
Press$ or% to select “Tire
pressure”.
Press#.
The message
“Run Flat Indicator
active
Restart possible with OK”
appears in the multifunction display.
Press#.
The message
“Tire pressure
now OK?”
appears in the multifunction display.If you wish to confirm activation:
Press$ or% to select “Yes”.
Press#.
The message
“Run Flat Indicator
restarted”
appears in the multifunction display.
After a certain “learning phase”, the Run
Flat Indicator checks the set pressure val-
ues for all four tires.
If you wish to cancel activation:
PressL.
or
When the message
“Tire pressure
now OK?”
appears in the multifunction display:
Press$ or% to select “Cancel”.
Press#.
Warning!G
The Run Flat Indicator can only warn you in
a reliable manner if you have set the correct
tire inflation pressures for each tire.
If an incorrect tire inflation pressure was
set, the system will monitor the pressure ac-
cording to the incorrect value.
iThe menu overview can be found on
(
page 266).