2008 MERCEDES-BENZ S600 buttons

285 Control systems
Voice Control* introduction
Voice Control* introduction
The Voice Control System gives you the ca-
pability to control the following systems on
your vehicle using spoken commands:

Telephone* (page 289)

Navigation (page 296)

Address book (page 306)

Audio (page 309) (AM/FM radio,
CD/DVD changer, MP3 player)You control these systems using spoken
commands. Moreover, controls such as
the buttons on the multifunction steering
wheel (
page 287) allow you to keep your
hands on the steering wheel.
The command vocabulary consists of
approximately 300 ready to use phrases.
The Voice Control System recognizes com-
mands and number sequences, irrespec-
tive of the speaker. To optimize speech
recognition for your voice follow the indi-
vidualization process (
page 330).
You can use the Voice Control System to
call up all of COMAND’s main menu items,
with the exception of the main menus for
“Vehicle” and “Navi”.The commands and digit sequences can be
spoken without pausing between the indi-
vidual words. If an unavailable or incorrect
command is used, the Voice Control Sys-
tem will prompt you for a new command by
asking “Please repeat” or “Please repeat
your entry”.
In order to provide for a safe and comfort-
able dialog, the Voice Control System ac-
knowledges important commands.

291 Control systems
Voice Control* telephone
“Dial number”
You can dial a phone number using the
command “Dial number”.
Digits from “Zero” to “Nine” may be used.
The phone number must be spoken

as a continuously spoken string of
digits, or

in digit blocks (three to five digits in
each block).
After each digit block (separate the digit
blocks by using an approximately 0.5 sec-
ond pause), the Voice Control System re-
peats the recognized digits and waits until
you continue speaking.
When dialing 1800 numbers, you may pro-
nounce the first four digits as “One eight
hundred” and the system will recognize the
spoken entries as “One eight zero zero”.
All other numeric entries must be spoken
as individual numbers.Sample dialog:
sDial number
tPlease say the number
sOne two three
tOne two three
sFour five six seven
tFour five six seven
sOK
tDialing“Confirm”
Using the command “Confirm” will repeat
all digits spoken up to that point. Upon re-
peating the digits, the system will prompt
you to continue your input.
Sample dialog:
sDial number
tPlease say the number
sOne two three
tOne two three
sConfirm
tOne two three, please continue
sFour five six seven
tFour five six seven
sOK
tDialing
iYou can also dial the telephone number spo-
ken by pressing buttons on the multifunc-
tion steering wheel (instead of using the
command “OK”):
You can dial the telephone number before all
numbers are recited in full.

334 Controls in detail
Locking and unlocking
Global locking: Press button‹.
With the trunk and both doors closed:

All turn signal lamps flash three
times.

An acoustic signal sounds three
times (if equipped and feature acti-
vated).

The locking knobs in the doors
move down.

The anti-theft alarm system is
armed.
Selective setting
If you frequently travel alone, you may wish
to reprogram the SmartKey so that press-
ing buttonŒ only unlocks the driver’s
door and the fuel filler flap.
Press and hold buttonsŒ and‹
simultaneously for about 5 seconds un-
til battery check lamp5 (
page 332)
flashes twice.The SmartKey will then function as fol-
lows:
Unlocking driver’s door and fuel fill-
er flap: Press buttonΠonce.

All turn signal lamps flash once.

An acoustic signal sounds once
(if equipped and feature activated).
For more information, see “Factory
setting” (
page 333).

The locking knob in the driver’s
door moves up.

The anti-theft alarm system is dis-
armed.
Global unlocking: Press buttonŒ
twice.

All turn signal lamps flash once.

An acoustic signal sounds once
(if equipped and feature activated).

The locking knobs in the doors
move up.

The anti-theft alarm system is dis-
armed.
Global locking: Press button‹.
With the trunk and both doors closed:

All turn signal lamps flash three
times.

An acoustic signal sounds three
times (if equipped and feature acti-
vated).

The locking knobs in the doors
move down.

The anti-theft alarm system is
armed.
Restoring to factory setting: Press
and hold buttonsŒ and‹ si-
multaneously for about 5 seconds until
battery check lamp5 (
page 332)
flashes twice.

335 Controls in detail
Locking and unlocking
SmartKey with KEYLESS-GO*
Vehicles equipped with KEYLESS-GO come
with two SmartKeys with KEYLESS-GO,
each with remote control and a removable
mechanical key.
The locking tabs for the mechanical key
portion of the two SmartKeys with
KEYLESS-GO are of different color to help
distinguish each SmartKey with
KEYLESS-GO unit.
The KEYLESS-GO function is integrated
into the SmartKey. On these vehicles, the
validity of the SmartKey with KEYLESS-GO
is checked every time you grasp an outside
door handle.
With the KEYLESS-GO function, you can
lock and unlock the vehicle without using
the remote control buttons on the
SmartKey and start the engine without in-
serting the SmartKey in the starter switch.The SmartKey with KEYLESS-GO centrally
locks and unlocks, when set to factory set-
tings (
page 338):

the doors

the trunk

the fuel filler flap
SmartKey with KEYLESS-GO
1‹ Lock button
2ŠOpening button for trunk
(
page 479)
3Locking tab for mechanical key
4ΠUnlock button
5Battery check lamp
6ÂPanic button (
page 65)
iWhen any outside door handle other than
the driver’s outside door handle is grasped, the
vehicle is centrally unlocked.
!To prevent possible malfunction, avoid ex-
posing the SmartKey with KEYLESS-GO to high
levels of electromagnetic radiation.
Warning!G
When leaving the vehicle, always take the
SmartKey with KEYLESS-GO* with you and
lock the vehicle. Do not leave children unat-
tended in the vehicle, or with access to an
unlocked vehicle. A child’s unsupervised ac-
cess to a vehicle could result in an accident
and/or serious personal injury.
Children could start the vehicle with a valid
SmartKey with KEYLESS-GO left in the vehi-
cle or with the KEYLESS-GO button on the
starter switch, or could release the electron-
ic parking brake, thereby putting them-
selves and others in danger. Switch off the
engine and take the SmartKey with
KEYLESS-GO with you even if you are only
leaving the vehicle for a short while.

339 Controls in detail
Locking and unlocking
Global locking: Close all doors and
touch outside of door handle1. Do
not keep your hand in the door handle
recess.
With the trunk and both doors closed:

All turn signal lamps flash three
times.

An acoustic signal sounds three
times (if equipped and feature acti-
vated).

The locking knobs in the doors
move down.

The anti-theft alarm system is
armed.Selective setting
If you frequently travel alone, you may wish
to reprogram the SmartKey with
KEYLESS-GO so when you, grasp the driv-
er’s outside door handle only the driver’s
door and the fuel filler flap unlocks.
Press and hold buttonsŒ and‹
simultaneously for about 5 seconds un-
til battery check lamp5 (
page 335)
flashes twice.
The SmartKey with KEYLESS-GO will
then function as follows:
Unlocking driver’s door and fuel fill-
er flap: Grasp the driver’s outside door
handle.

All turn signal lamps flash once.

An acoustic signal sounds once
(if equipped and feature activated).
For more information, see “Factory
setting” (
page 338).

The locking knob in the driver’s
door moves up.

The anti-theft alarm system is dis-
armed.
Global unlocking: Grasp any outside
door handle other than the driver’s out-
side door handle.

All turn signal lamps flash once.

An acoustic signal sounds once
(if equipped and feature activated).

The locking knobs in the doors
move up.

The anti-theft alarm system is dis-
armed.
iVehicles with trunk opening/closing
system*:
You can also lock the vehicle using the
KEYLESS-GO locking/closing switch
(
page 482).


340 Controls in detail
Locking and unlocking
Global locking: Close all doors and
touch outside of door handle1
(
page 338). Do not keep your hand in
the door handle recess.
With the trunk and both doors closed:

All turn signal lamps flash three
times.

An acoustic signal sounds three
times (if equipped and feature acti-
vated).

The locking knobs in the doors
move down.

The anti-theft alarm system is
armed.
Restoring to factory setting: Press
and hold buttonsŒ and‹ si-
multaneously for about 5 seconds until
battery check lamp5 (
page 335)
flashes twice.Checking batteries in the SmartKey or
SmartKey with KEYLESS-GO*
Press button‹ orŒ.
The battery check lamp (
page 332)
or (
page 335) comes on briefly to in-
dicate that the SmartKey or SmartKey
with KEYLESS-GO batteries are in or-
der.Loss of the SmartKey or SmartKey with
KEYLESS-GO*
If you lose your SmartKey, SmartKey with
KEYLESS-GO or mechanical key, you
should do the following:
Have the SmartKey or SmartKey with
KEYLESS-GO deactivated by an autho-
rized Mercedes-Benz Center.
Report the loss of the SmartKey,
SmartKey with KEYLESS-GO or the me-
chanical key immediately to your car
insurance company.
Have the mechanical lock replaced if
necessary.
Any authorized Mercedes-Benz Center will
be glad to supply you with a replacement.
iVehicles with trunk opening/closing
system*:
You can also lock the vehicle using the
KEYLESS-GO locking/closing switch
(
page 482).
!If the battery check lamp does not come on
briefly during check, the SmartKey or SmartKey
with KEYLESS-GO batteries are discharged.
Replace the batteries (
page 676).
You can obtain the required batteries at any au-
thorized Mercedes-Benz Center.
iIf the batteries are checked within signal
range of the vehicle, pressing button‹ or
Πwill lock or unlock the vehicle accordingly.


351 Controls in detail
Seats
Switch on the ignition (page 344).
or
Open the right rear passenger door.
Press button1 to adjust the front
passenger seat.
The indicator lamp in button1 comes
on.
Adjust front passenger seat using seat
switches2,3,4 and5.
To adjust right rear passenger seat
(
page 349), press button1 again.
The indicator lamp in button1 goes
out.
Seat heating*
The buttons for seat heating are located on
the respective door. The red indicator
lamps on the button come on to show the
heating level selected.
Example illustration driver’s door
1Seat heating button
Switch on the ignition (page 344).
Switching on: Press button1 repeat-
edly until the desired heating level is
set.
One or more red indicator lamps on the
button show the selected heating level.
Switching off: Press button1 repeat-
edly until all indicator lamps go out.
iAdjusting the passenger seat position from
the rear is not possible if you deactivate the over-
ride switch (
page 63).
Level
3Three indicator lamps on
(highest level)
The seat heating automatically
switches to level2 after approxi-
mately 5 minutes.
2Two indicator lamps on
The seat heating automatically
switches to level1 after approxi-
mately 10 minutes.
1One indicator lamp on
(lowest level)
The seat heating automatically
switches off after approximately
20 minutes.
offNo indicator lamp on


352 Controls in detail
Seats
Seat ventilation*
The buttons for seat ventilation are located
on the respective door. The blue indicator
lamps on the button come on to show the
ventilation level selected.
Example illustration driver’s door
1Seat ventilation button
Switch on the ignition (page 344).
Switching on: Press button1 repeat-
edly until the desired ventilation level is
set.
One or more blue indicator lamps on
the button show the selected ventila-
tion level.
Switching off: Press button1 repeat-
edly until all indicator lamps go out.iIf one or more of the lamps on the seat heat-
ing button are flashing, there is insufficient volt-
age available since too many electrical
consumers are turned on. The seat heating
switches off automatically.
The seat heating will switch back on again auto-
matically as soon as sufficient voltage is avail-
able.
Level
3Three indicator lamps on
(highest level)
2Two indicator lamps on
1One indicator lamp on
(lowest level)
offNo indicator lamp on
iThe seat ventilation for the driver’s seat can
be activated using summer opening feature
(
page 385).iIf one or more of the lamps on the seat ven-
tilation button are flashing, there is insufficient
voltage available since too many electrical con-
sumers are turned on. The seat ventilation
switches off automatically.
The seat ventilation will switch back on again au-
tomatically as soon as sufficient voltage is avail-
able.