2008 MERCEDES-BENZ ML63AMG adding oil

344 Operation
Engine compartment
Open the hood (page 341).
Pull out oil dipstick1.
Wipe oil dipstick1 clean.
Fully insert oil dipstick1 into the
dipstick guide tube.
Pull out oil dipstick1 again after
approximately 3 seconds to obtain
accurate reading.
The oil level is correct when it is be-
tween lower mark3 (min.) and upper
mark2 (max.) of the oil dipstick.
If necessary, add engine oil
(
page 344).For more information on engine oil, see
“Technical data” section (
page 522) and
(
page 525).
Adding engine oil
Example illustration ML 320 CDI (ML 350,
ML 550 similar)
1Filler cap
ML 63 AMG
1Filler cap
iAll models (except ML 63 AMG):
The filling quantity between the upper and lower
marks on the oil dipstick is approximately
2.1 US qt. (2.0 l).
ML 63 AMG:
The filling quantity between the upper and lower
marks on the oil dipstick is approximately
1.6 US qt. (1.5 l).
!Only use approved engine oils and oil filters
required for vehicles with Maintenance System.
For a listing of approved engine oils and oil
filters, refer to the Factory Approved Service
Products pamphlet (USA only) in your vehicle
literature portfolio, or contact an authorized
Mercedes-Benz Light Truck Center.
Using engine oils and oil filters of specification
other than those expressly required for the
Maintenance System, or changing of oil and oil
filter at change intervals longer than those called
for by the Maintenance System will result in
engine or emission control system damage not
covered by the Mercedes-Benz Limited
Warranty.


345 Operation
Engine compartment
Unscrew filler cap1 from filler neck.
Add engine oil as required. Never over-
fill with oil.
Be careful not to spill any oil when adding.
Avoid environmental damage caused by oil
entering the ground or water.
Screw filler cap1 back on filler neck.
For more information on engine oil, see
“Technical data” section (
page 522) and
(
page 525).
Transmission fluid level
The transmission fluid level does not need
to be checked. If you notice transmission
fluid loss or gear shifting malfunctions,
have an authorized Mercedes-Benz Light
Truck Center check the automatic trans-
mission.
Coolant level
The engine coolant is a mixture of water
and anticorrosion/antifreeze.
When checking the coolant level

the vehicle must be parked on level
ground

the coolant temperature must be below
158°F (70°C)
!Excess oil must be siphoned or drained off.
It could cause damage to the engine and/or
catalytic converter (gasoline engine) or the oxi-
dation catalyst (diesel engine) not covered by
the Mercedes-Benz Limited Warranty.
Warning!G
In order to avoid potentially serious burns:

Use extreme caution when opening the
hood if there are any signs of steam or
coolant leaking from the cooling system,
or if the coolant temperature display
indicates that the coolant is overheated.

Do not remove pressure cap on coolant
reservoir if coolant temperature is
above 158°F (70°C). Allow engine to
cool down before removing cap. The
coolant reservoir contains hot fluid and
is under pressure.

Using a rag, slowly open the cap approx-
imately 1/2 turn to relieve excess pres-
sure. If opened immediately, scalding
hot fluid and steam will be blown out
under pressure.

Do not spill antifreeze on hot engine
parts. Antifreeze contains ethylene
glycol which may burn if it comes into
contact with hot engine parts.

528 Technical data
Fuels, coolants, lubricants
Coolants
The engine coolant is a mixture of water
and anticorrosion/antifreeze, which
provides:

Corrosion protection

Freeze protection

Boiling protection (by increasing the
boiling point)
The cooling system was filled at the factory
with a coolant providing freeze protection
to approximately -35°F (-37°C) and corro-
sion protection.If the antifreeze mixture is effective to
-35°F (-37°C), the boiling point of the cool-
ant in the pressurized cooling system is
reached at approximately 266°F (130°C).
The coolant solution must be used year
round to provide the necessary corrosion
protection and increase boil-over protec-
tion. Refer to Maintenance Booklet for
replacement interval.
Coolant system design and coolant used
determine the replacement interval. The
replacement interval published in the
Maintenance booklet is only applicable if
MB 325.0 Anticorrosion/Antifreeze solu-
tion or other Mercedes-Benz approved
products of equal specification are used to
renew the coolant concentration or bring it
back up to the proper level.
For information on other Mercedes-Benz
approved products of equal specification,
refer to the Factory Approved Service
Products pamphlet (USA only) or contact
an authorized Mercedes-Benz Light Truck
Center.To provide important corrosion protection,
the solution must be at least 50% anticor-
rosion/antifreeze (equivalent to freeze
protection to approximately -35°F
[-37°C]). If you use a solution that is more
than 55% anticorrosion/antifreeze (freeze
protection to approximately -49°F
[-45°C]), the engine temperature will
increase due to the lower heat transfer
capability of the solution. Therefore, do not
use more than this amount of anticorro-
sion/antifreeze.
If the coolant level is low, water and
MB 325.0 Anticorrosion/Antifreeze
should be used to bring it up to the proper
level (have cooling system checked for
signs of leakage). Please make sure the
mixture is in accordance with label instruc-
tions.
The water in the cooling system must meet
minimum requirements, which are usually
satisfied by normal drinking water. If you
are not sure about the water quality, con-
sult an authorized Mercedes-Benz Light
Truck Center.
!Add premixed coolant solution only. Adding
water and MB 325.0 Anticorrosion/Antifreeze
separately from each other, could cause engine
damage not covered by the
Mercedes-Benz Limited Warranty.

537 Index
Engine
Belt layout (ML 320 CDI) 512
Belt layout (ML 350, ML 550) 512
Belt layout (ML 63 AMG) 512
Block heater (Canada only) 385
Break-in recommendations 343
Cleaning 391
Compartment 341
Emergency engine shut-down 506
Malfunction indicator lamp 29
Maximum engine speed 146, 513,
514
Number 511
Starting 54
Starting with KEYLESS-GO* 55
Starting with the SmartKey 55
Tachometer 29, 146
Technical data 513
Turning off with KEYLESS-GO* 67
Turning off with the SmartKey 67Engine coolant see Coolant
Engine oil 343, 525
Adding 344, 525
Additives 525
Changing 344, 525
Checking level 343
Checking with the oil dipstick 343
Consumption 343
Filler neck (ML 350, ML 320 CDI) 344
Filler neck (ML 550, ML 63 AMG) 344
Recommended engine oils and oil
filters 525
ESP
®27, 100
Four wheel electronic traction system
with ESP
®100
Messages in the multifunction
display 418, 419
Off-road-ESP
®103
Warning lamp 27, 405
ETD 87, 410
Safety guidelines 76
Expanding cargo compartment 269Exterior rear view mirrors 49, 199
Folding 201
Power folding* 200
Synchronizing 200
F
Fastening the seat belts 51
Filler neck, Engine oil
(ML 350, ML 320 CDI) 344
Filler neck, Engine oil
(ML 550, ML 63 AMG) 344
First aid kit 448
Flat tire 478
Collapsible tire
(ML 63 AMG only) 453, 518
Lifting the vehicle 479
Lowering the vehicle 487
Minispare wheel
(except ML 63 AMG) 452
Mounting the spare wheel 479
Preparing the vehicle 479
Spare wheel 518
Floormats 289