Page 21 of 561

20 Introduction
Vehicle data recording
Information regarding electronic
recording devices
(Including notice pursuant to California Code § 9951)
Please note that your vehicle is equipped with devices that can record vehicle systems data and, if equipped with the Tele Aid system,
may transmit some data in certain accidents.
This information helps, for example, to diagnose vehicle systems after a collision and to continuously improve vehicle safety.
DaimlerChrysler may access the information and share it with others
for safety research or vehicle diagnosis purposes
with the consent of the vehicle owner or lessee
in response to an official request by law enforcement or other government agency
for use in dispute resolution involving DaimlerChrysler, its affiliates or sales/service organization and/or
as otherwise required or permitted by law.
Please check the Tele Aid subscription service agreement for details regarding the information that may be recorded or transmitted
via that system.
Page 307 of 561

306 Controls in detail
Useful features
Operation of integrated remote control
Switch on the ignition (page 40).
Select and press the appropriate inte-
grated signal transmitter button (2,
3 or4) to activate the remote con-
trolled device.
The integrated remote control trans-
mitter continues to send the signal as
long as the button is pressed – up to
20 seconds.
Erasing the integrated remote control
memory
Switch on the ignition (page 40).
Simultaneously press and hold outer
signal transmitter buttons2 and 4,
for approximately 20 seconds, until
indicator lamp1 flashes rapidly. Do
not hold for longer than 30 seconds.
The codes of all three channels are
erased.Programming tips
If you are having difficulty programming
the integrated remote control, here are
some helpful tips:
Check the frequency of hand-held
remote control5 (typically located on
the reverse side of the remote). The in-
tegrated remote control is compatible
with radio-frequency devices operating
between 280-390 MHz.
Put a new battery in hand-held remote
control5. This will increase the likeli-
hood of the hand-held remote control
sending a faster and more accurate sig-
nal to the integrated remote control.
While performing step 3, hold
hand-held remote control5 at differ-
ent lengths and angles from the signal
transmitter button (2, 3 or4) you
are programming. Attempt varying
angles at the distance of 2 to 5 in
(5 to 12 cm) away or the same angle at
varying distances.
If another hand-held remote control is
available for the same device, try the
programming steps again using that
other hand-held remote control. Make
sure new batteries are in the hand-held
remote control before beginning the
procedure.
Straighten the antenna wire from the
garage door opener assembly. This
may help improve transmitting and/or
receiving signals.
iIf you sell your vehicle, erase the codes of all
three channels.
iCertain types of garage door openers are in-
compatible with the integrated remote control. If
you should experience further difficulties with
programming the integrated remote control,
contact an authorized Mercedes-Benz Light
Truck Center, or call Mercedes-Benz Customer
Assistance Center (in the USA only) at
1-800-FOR-MERCedes, or Customer Service (in
Canada) at 1-800-387-0100.
Page 404 of 561

403 Practical hints
What to do if …
ProblemPossible cause/consequenceSuggested solution
?(USA only)
±(Canada only)
The yellow engine malfunc-
tion indicator lamp comes on
while driving.There is a malfunction in:
The fuel management system
The ignition system
The emission control system
Systems which affect
emissions
Such malfunctions may result in
excessive emissions values and
may switch the engine to its
limp-home (emergency opera-
tion) mode.
Have the vehicle checked as soon as
possible by an authorized
Mercedes-Benz Light Truck Center.
An on-board diagnostic connector is
used by the service station to link the
vehicle to the shop diagnostics
system. It allows the accurate identi-
fication of system malfunctions
through the readout of diagnostic
trouble codes. It is located in the
front left area of the footwell next to
the parking brake pedal.
iSome states may by law require you to visit
a workshop as soon as the engine malfunction
indicator lamp comes on. Check local require-
ments.
Page 546 of 561

545 Index
Ornamental moldings, Cleaning 393
Outside temperature see Displays
Overdue maintenance service term 387
Overhead control panel 33
Oxidation catalyst (diesel engine) 335
P
Paintwork code 510
Paintwork, Cleaning 390
Panic alarm 97
Parcel net
Front passenger footwell 283
Front seat backrests 283
Parking 65, 315
On hills 65
Over things that burn, Potential
consequences 65, 335
Parking brake 57, 65
Lamps, Indicator and warning 401
Messages in the multifunction
display 429
Releasing 57
Parking lamps
Messages in the multifunction
display 441
Replacing bulbs 468Parking position*
Exterior rear view mirrors 177, 200
Parktronic* 31, 259
Cleaning system sensors 394
Minimum distance 261
Range 261
Switching on/off 263
System malfunction 263
System sensors 260
System sensors, Cleaning 394
Warning indicators 25, 262
Parts service 508
PASS AIR BAG OFF indicator lamp see
Front passenger front air bag off
indicator lamp
Passenger compartment 334
Fuse box 506
Interior lighting 142
Interior rear view mirror 33
Parcel net in front passenger
footwell 283Passenger safety see Occupant safety
Pedals 311
Phone see Telephone*
Plastic and rubber parts, cleaning 396
Poly-V-belt drive
Layout (ML 320 CDI) 512
Layout (ML 350, ML 550) 512
Layout (ML 63 AMG) 512
Positions (Memory function*) see Seats
Pounds per square inch see PSI
Power assistance 312
Power outlets 287
Power seat see Seats, Power
Power tilt/sliding sunroof 240
Convenience closing feature 238
Opening/closing 240
Stopping 238
Summer opening feature 237
Synchronizing 242
Power washer 390