2008 MERCEDES-BENZ ML SUV spare wheel

Locking/unlocking in an emergency
309
X
Turn the emergency key element back and
remove it.
X Pull the door handle again. Locking the vehicle
If the vehicle can no longer be locked cen-
trally with the key or the KEYLESS GO key*:
X Close the front-passenger door, the rear
door on the front-passenger side and the
tailgate.
X Open the driver's door and the rear door on
the driver's side.
X Press the locking button on the driver's
door (Y page 74).
The locking knobs in the front-passenger
door and in the rear doors drop down.
X Press the locking knobs in the front-
passenger and rear doors down manually if
necessary.
X Exit the vehicle.
X Close the driver's door.
X Enter the vehicle through the rear door on
the driver's side.
X Push the locking pin in the driver's door
down from the inside.
X Exit the vehicle. i
Ensure that you have the vehicle key on
your person and that it is not left in the
vehicle, as the vehicle will be locked after
the next step.
X Close the rear door on the driver's side.
The vehicle is locked. Unlocking the exterior spare wheel
bracket*
1
Crank
X Take crank 1from the glove compart-
ment.
i You can also use a screwdriver, key or
similar implement. X
Insert crank 1into the hole under the
spare wheel bracket.
X Push crank 1up in the direction of the
arrow.
The spare wheel bracket is unlocked. Unlocking the tailgate
If the tailgate cannot be opened, use the
emergency release on the inside of the tail-
gate. 1
Release catch
2 Release catch cover
! The tailgate swings upwards and to the
rear when opened. Therefore, make sure
that there is sufficient clearance above and
behind the tailgate. Practical advice
* optional
164_AKB; 5; 5, en-GB
wobuchh,
Version: 2.10.6 2008-05-11T11:55:12+02:00 - Seite 309 ZDateiname: 6515_4293_02_buchblock.pdf; preflight

Changing the bulbs
314 Bulb Type
1 Third brake
lamp LED
36 2 Brake lamp P 21 W
or
LED*
36 3 Turn signal lamp PY 21 W
or
LED*
36 4 Foglamp/tail
lamp/parking
lamp
or P 21 W
or
Rear fog lamp
Side lamp/park-
ing lamp
W 16 W*
LED*
36 5 Foglamp/tail
lamp/parking
lamp
or P 21 W
or
Rear fog lamp
Side lamp/park-
ing lamp
W 16 W*
LED*
36 Bulb Type
6 Reversing lamp P 21 W
or
W 16 W*
7 Licence plate
lamp C 5 W
Vehicles with an exterior spare wheel bracket*
Bulb Type
1 Third brake
lamp
LED
36 2 Reversing lamp P 21 W
3 Rear fog lamp P 21 W Bulb Type
4 Brake lamp/tail
lamp/parking
lamp P 21 W
5 Turn signal lamp PY 21 W
6 Licence plate
lamp W 5 W
Before changing bulbs
You can replace the following bulbs:
R
Dipped-beam headlamps (vehicles with
halogen headlamps)
R Main-beam headlamps
R Side lamp and parking lamp
R Foglamps with/without cornering light
function*
R Turn signal lamp (front)
R Brake lamp
R Reversing lamp
R Rear foglamp/tail lamp/parking lamp
R Turn signal lamp (rear)
R Licence plate lamp
36 These bulbs must be replaced at a qualified specialist workshop, e.g. a Mercedes-Benz Service Centre. Practical advice
* optional
164_AKB; 5; 5, en-GB
wobuchh,
Version: 2.10.6 2008-05-11T11:55:12+02:00 - Seite 314Dateiname: 6515_4293_02_buchblock.pdf; preflight

Changing the bulbs
320Tail lamps with LEDs*
1
Reversing lamp
2 Rear fog lamp
3 Rear fog lamp
X Turn the corresponding bulb holder anti-
clockwise and remove it.
X Take the bulb out of the bulb holder.
X Insert the new bulb into the bulb holder.
X Insert the bulb holder and turn it clockwise.
X Close the side trim panel (Y page 318).Vehicles with an exterior spare wheel
bracket*
On vehicles with an exterior spare wheel
bracket*, the following lamps are located in
the bumper:
R
Tail lamp
R Parking lamp
R Brake lamp
R Turn signal lamp
R Licence plate lamp Bumper
1
Lamp cluster
X Switch off the lights.
X Insert a plastic card into the gap between
the bumper and lamp cluster 1.X
Push the plastic card in the direction of the
arrow.
Lamp cluster 1pops out.
X Remove lamp cluster 1. Lamp cluster
1
Bulb holder for turn signal lamp
2 Bulb holder for tail lamp/parking lamp/
brake lamp
X Turn the corresponding bulb holder anti-
clockwise and remove it.
X Lightly press the bulb into the bulb holder,
turn it anti-clockwise and remove it from
the bulb holder.
X Insert the new bulb into the bulb holder and
turn it clockwise. Practical advice
* optional
164_AKB; 5; 5, en-GB
wobuchh,
Version: 2.10.6 2008-05-11T11:55:12+02:00 - Seite 320Dateiname: 6515_4293_02_buchblock.pdf; preflight

Flat tyre
323Flat tyre
Flat tyre equipment variants
Your vehicle may be equipped with:
R a TIREFIT kit (Y page 255)
R a "Minispare" emergency spare
wheel* (Y page 256)
R a collapsible emergency spare
wheel* (Y page 258)
R a spare wheel* (Y page 256)
R the MOExtended run-flat sys-
tem* (Y page 333) Preparing the vehicle
i Vehicle preparation is not necessary on
vehicles with MOE tyres*.
X Make sure that highway level* is selec-
ted 37
(Y page 158).
X Stop your vehicle as far away from traffic
as possible on solid, non-slippery, level
ground.
X Switch on the hazard warning lamps. X
Firmly depress the parking brake.
X Move the selector lever to P.
X All occupants must get out of the vehicle.
Make sure that they are not endangered as
they do so.
X Make sure that no one is near the danger
area whilst a wheel is being changed. Any-
one who is not directly assisting in the
wheel change should, for example, stand
behind the barrier.
X Switch off the engine.
Vehicles without KEYLESS GO* X
Remove the key from the ignition lock.
Vehicles with KEYLESS GO* X
Open the driver's door.
The on-board electronics have status 0,
which is the same as the key having been
removed.
X Vehicles with the AIRMATIC package* and
the Off-Road Pro engineering package*:
Remove the KEYLESS GO button from the
ignition lock. For all vehicles X
Get out of the vehicle.
X Close the driver's door.
X Place the warning triangle ( Ypage 254) at
a suitable distance. Observe legal require-
ments.
i To operate the electric air-pump, you can
use the power socket in the luggage com-
partment (Y page 205) or rear compart-
ment (Y page 205), even when the ignition
is switched off. For example, to use TIREFIT
or to inflate the collapsible emergency
spare wheel*.
An emergency cut-off ensures that the on-
board voltage does not drop too low. If the
on-board voltage is too low, power to the
sockets is automatically cut-off. This
ensures that there is sufficient power to
start the engine.
37 Not on steel-sprung vehicles. Practical advice
* optional
164_AKB; 5; 5, en-GB
wobuchh,
Version: 2.10.6 2008-05-11T11:55:12+02:00 - Seite 323 ZDateiname: 6515_4293_02_buchblock.pdf; preflight

Flat tyre
327Changing a wheel/fitting the emer-
gency spare wheel*
G
Risk of accident
The wheel dimensions and tyre size of the
spare wheel*, the emergency spare
wheel* and standard wheels may differ
from one another.
The handling characteristics of your vehicle
will change if you fit an emergency spare
wheel*. Adapt your style of driving accord-
ingly.
You may only use the emergency spare
wheel* for a short while. Do not exceed the
maximum speed of 80 km/h and do not
deactivate ESP ®
.
Never drive the vehicle with more than one
emergency spare wheel* fitted. G
Risk of accident
Have the "Minispare" emergency spare
wheel* or the spare wheel* replaced with
a new wheel as soon as possible at a quali-
fied specialist workshop which has the nec-
essary specialist knowledge and tools to
carry out the work required. Mercedes-
Benz recommends that you use a
Mercedes-Benz Service Centre for this pur- pose. In particular, work relevant to safety
or on safety-related systems must be car-
ried out at a qualified specialist workshop.
Preparing the vehicle X
Prepare the vehicle as described
(Y page 323).
X If a trailer is coupled, uncouple it.
X Position the wheels in the straight-ahead
position.
X Take the following from the stowage well
beneath the luggage compartment floor:
R
the wheel wrench
R the wheel chock
R the jack
X Secure the vehicle to prevent it from rolling
away.
On level ground: place chocks or similar
items under the front and rear of the wheel
that is diagonally opposite the wheel you
wish to change. Securing a vehicle on level ground (example illus-
tration)
X
On downhill gradients: place chocks or
similar items under both wheels of the
other axle. Securing a vehicle on slight downhill slopes (exam-
ple illustration) Practical advice
* optional
164_AKB; 5; 5, en-GB
wobuchh,
Version: 2.10.6 2008-05-11T11:55:12+02:00 - Seite 327 ZDateiname: 6515_4293_02_buchblock.pdf; preflight

Flat tyre
328
Spare wheel* or the "Minispare" emer-
gency spare wheel*
X Remove the spare wheel from the exterior
bracket (Y page 256).
or
X Remove the "Minispare" emergency spare
wheel from the stowage compartment
under the luggage compartment floor
(Y page 256).
Raising the vehicle G
Risk of injury
The jack is designed only to raise the vehi-
cle for a short time while a wheel is being
changed.
If you intend to work under the vehicle, it
must be placed on stands.
Make sure that the jack is placed on a firm,
non-slip, level surface. Do not use wooden
blocks or similar items as jacking supports.
Otherwise, the jack will not be able to ach-
ieve its load-bearing capacity due to the
restricted height.
Do not start the engine at any time while
the wheel is being changed.
Do not lie under the vehicle when it is being
supported by the jack. If you do not raise the vehicle as described, it could slip off the
jack (e.g. if the engine is started or a door
or the tailgate is opened or closed) and you
could be seriously injured.
G
Risk of accident
If you fail to position the jack correctly, the
vehicle may:
R slip off the jack
R injure you or others
R be damaged
It is thus important to ensure that the jack
is positioned correctly in the respective
jacking points. Before positioning the jack,
remove any dirt that may have collected in
the jacking points. 1
Wheel wrench X
Using wheel wrench 1, loosen the bolts on
the wheel you wish to change by about one
full turn. Do not unscrew the bolts com-
pletely.
The jacking points for the jack are located
behind the wheel housings of the front wheels
and in front of the wheel housings of the rear
wheels (arrows). Practical advice
* optional
164_AKB; 5; 5, en-GB
wobuchh,
Version: 2.10.6 2008-05-11T11:55:12+02:00 - Seite 328Dateiname: 6515_4293_02_buchblock.pdf; preflight

Flat tyre
330 safety reasons, Mercedes-Benz recom-
mends that you only use wheel bolts which
have been approved for Mercedes-Benz
vehicles. Other bolts could work loose.
Do not tighten the wheel bolts completely
while the vehicle is still jacked up. The vehi-
cle could topple off the jack. 1
Wheel bolts for 18", 19" and 20" wheels
2 Wheel bolts for 17" wheels or the
"Minispare" emergency spare wheel*
! Always use wheel bolts 2to fit 17"
wheels or the "Minispare" emergency spare
wheel*. Using other wheel bolts when fit-
ting 17" wheels or the "Minispare" emer-
gency spare wheel* could damage the
brake system. i
Wheel bolts 2can be found together
with the "Minispare" emergency spare
wheel* (not with 17" tyres).
X Clean the wheel and wheel hub contact
surfaces. X
Slide the emergency spare wheel* or the
spare wheel onto the centring pin and push
it on. X
Tighten the wheel bolts until they are fin-
ger-tight.
X Unscrew the centring pin.
X Tighten the last wheel bolt until it is finger-
tight.
Inflating the "Minispare" emergency
spare wheel* (ML 63 AMG only) G
Risk of accident
Pump up the collapsible emergency spare
wheel before lowering the vehicle, as you
could otherwise damage the wheel rim.
X Take the electric air pump out of the stow-
age well under the luggage compartment
floor (Y page 258). Practical advice
* optional
164_AKB; 5; 5, en-GB
wobuchh,
Version: 2.10.6 2008-05-11T11:55:12+02:00 - Seite 330Dateiname: 6515_4293_02_buchblock.pdf; preflight

Flat tyre
332
X
Press on/off switch 2on the electric air
pump to I.
The electric air pump is switched on. The
tyre is inflated.
X When a tyre pressure of 3.5 bar has been
reached, press 0on electric air pump on/
off switch 2.
The electric air pump is switched off.
! Do not operate the electric air pump for
longer than eight minutes at a time without
a break. Otherwise, it may overheat.
The air pump can be operated again once
it has cooled down.
If the tyre pressure is higher than 3.5 bar:
X Version 1: open pressure release
screw 4on the pressure gauge until the
tyre pressure is correct.
X Version 2: press pressure release button
6 until the tyre pressure is correct.
X Switch off the electric air pump with on/off
switch 2, remove from the tyre valve and
stow it away. Lowering the vehicle X
Place the ratchet ring spanner onto the
hexagon nut of the jack so that the lettering
AB is visible.
X Lower the vehicle by turning the ratchet
ring spanner until the vehicle is once again
standing firmly on the ground.
X Place the jack to one side. 1
–5 Wheel bolts
X Tighten the wheel bolts evenly in a cross-
wise pattern in the sequence indica-
ted (1 to5). The tightening torque is
150 Nm . G
Risk of accident
Have the tightening torque checked imme-
diately after a wheel is changed. The wheels could work loose if they are not tightened
to a torque of
150 Nm.
X Turn the jack back to its initial position and
stow it and the rest of the vehicle tool kit in
the luggage compartment.
Vehicles with the "Minispare" emergency
spare wheel*:
X Wrap the faulty wheel in the protective film
included with the "Minispare" emergency
spare wheel* and transport the wheel in
the luggage compartment.
or
X Depending on the size of the wheel, you
may also be able to secure the faulty wheel
in the emergency spare wheel well. In this
case, you will have to remove the stowage
tray from the emergency spare wheel well
and stow it securely in the luggage com-
partment.
Vehicles with a spare wheel*:
X Use the fastening bolts to secure the faulty
wheel to the exterior spare wheel
bracket*. Practical advice
* optional
164_AKB; 5; 5, en-GB
wobuchh,
Version: 2.10.6 2008-05-11T11:55:12+02:00 - Seite 332Dateiname: 6515_4293_02_buchblock.pdf; preflight