381 Operation
Engine compartment
Adding engine oil
Example illustration GL 450 (GL 320 CDI,
GL 550 similar)
1Filler cap
Unscrew filler cap1 from filler neck.
Add engine oil as required. Never over-
fill with oil.
Be careful not to spill any oil when adding.
Avoid environmental damage caused by oil
entering the ground or water.
Screw filler cap1 back on filler neck.
For more information on engine oil, see
“Technical data” section (
page 562) and
(
page 564).
Transmission fluid level
The transmission fluid level does not need
to be checked. If you notice transmission
fluid loss or gear shifting malfunctions,
have an authorized Mercedes-Benz Light
Truck Center check the automatic trans-
mission.
Coolant level
The engine coolant is a mixture of water
and anticorrosion/antifreeze.
When checking the coolant level
the vehicle must be parked on level
ground
the coolant temperature must be below
158°F (70°C)
!Only use approved engine oils and oil filters
required for vehicles with Maintenance System.
For a listing of approved engine oils and oil
filters, refer to the Factory Approved Service
Products pamphlet (USA only) in your vehicle
literature portfolio, or contact an authorized
Mercedes-Benz Light Truck Center.
Using engine oils and oil filters of specification
other than those expressly required for the
Maintenance System, or changing of oil and oil
filter at change intervals longer than those called
for by the Maintenance System will result in
engine or emission control system damage not
covered by the Mercedes-Benz Limited
Warranty.
!Excess oil must be siphoned or drained off.
It could cause damage to the engine and/or
catalytic converter (gasoline engine) or the oxi-
dation catalyst (diesel engine) not covered by
the Mercedes-Benz Limited Warranty.
164.boo Seite 381 Freitag, 30. März 2007 12:54 12
567 Technical data
Fuels, coolants, lubricants
Coolants
The engine coolant is a mixture of water
and anticorrosion/antifreeze, which
provides:
Corrosion protection
Freeze protection
Boiling protection (by increasing the
boiling point)
The cooling system was filled at the factory
with a coolant providing freeze protection
to approximately -35°F (-37°C) and corro-
sion protection.If the antifreeze mixture is effective to
-35°F (-37°C), the boiling point of the cool-
ant in the pressurized cooling system is
reached at approximately 266°F (130°C).
The coolant solution must be used year
round to provide the necessary corrosion
protection and increase boil-over protec-
tion. Refer to Maintenance Booklet for
replacement interval.
Coolant system design and coolant used
determine the replacement interval. The
replacement interval published in the
Maintenance booklet is only applicable if
MB 325.0 Anticorrosion/Antifreeze solu-
tion or other Mercedes-Benz approved
products of equal specification are used to
renew the coolant concentration or bring it
back up to the proper level.
For information on other Mercedes-Benz
approved products of equal specification,
refer to the Factory Approved Service
Products pamphlet (USA only) or contact
an authorized Mercedes-Benz Light Truck
Center.To provide important corrosion protection,
the solution must be at least 50% anticor-
rosion/antifreeze (equivalent to freeze
protection to approximately -35°F
[-37°C]). If you use a solution that is more
than 55% anticorrosion/antifreeze (freeze
protection to approximately -49°F
[-45°C]), the engine temperature will
increase due to the lower heat transfer
capability of the solution. Therefore, do not
use more than this amount of anticorro-
sion/antifreeze.
If the coolant level is low, water and
MB 325.0 Anticorrosion/Antifreeze
should be used to bring it up to the proper
level (have cooling system checked for
signs of leakage). Please make sure the
mixture is in accordance with label instruc-
tions.
The water in the cooling system must meet
minimum requirements, which are usually
satisfied by normal drinking water. If you
are not sure about the water quality, con-
sult an authorized Mercedes-Benz Light
Truck Center.
!Add premixed coolant solution only. Adding
water and MB 325.0 Anticorrosion/Antifreeze
separately from each other, could cause engine
damage not covered by the
Mercedes-Benz Limited Warranty.
164.boo Seite 567 Freitag, 30. März 2007 12:54 12
577 Index
Emergency operation
Fuel filler flap 497
Locking/unlocking the vehicle 496,
497
Emergency operation
(Limp-Home Mode) 200
Emergency operations
Exit for third-row seats 132
Remote door unlock, Tele Aid 337
Tailgate, Opening from the inside
manually 122
Emergency Tensioning Device see ETD
Emergency, In case of
Battery, Jump starting 536
Engine shut-down 545
First aid kit 490
Flat tire 519
Fuses 543
Hazard warning flasher 149
Instrument cluster, Indicator
lamps 436, 437, 438, 439, 440,
441, 442, 443, 444, 446
Roadside Assistance 12, 335
Towing the vehicle 538Emission control 372
Information label 551
System warranties 10
Engine
Belt layout (GL 450, GL 550) 552
Belt layout (GL 320 CDI) 552
Break-in recommendations 380
Cleaning 427
Compartment 378
Emergency engine shut-down 545
Malfunction indicator lamp 29
Maximum engine speed 153, 553
Number 551
Starting 56
Starting with KEYLESS-GO* 57
Starting with the SmartKey 57
Tachometer 29, 153
Technical data 553
Turning off with KEYLESS-GO* 69
Turning off with the SmartKey 69Engine coolant see Coolant
Engine oil 380, 564
Adding 381, 564
Additives 564
Changing 381, 564
Checking level 380
Checking with the oil dipstick 380
Consumption 380
Filler neck 381
Recommended engine oils and oil
filters 564
Enhanced Off-road Package*
Vehicle level control 283
ESP
®27, 103
Four wheel electronic traction system
with ESP
®103
Messages in the multifunction
display 457, 458
Off-road-ESP
®106
Warning lamp 27, 441
164.boo Seite 577 Freitag, 30. März 2007 12:54 12
