2008 MERCEDES-BENZ G55AMG remote start

[x] Cancel search: remote start

seat memory oil change dashboard warning lights engine oil capacity child seat radio antenna

Page 39 of 457

MERCEDES-BENZ G55AMG 2008 W463 Owners Manual 38 Getting started
The “Getting started” section provides an
overview of the vehicle’s most basic func-
tions. First-time Mercedes-Benz owners
should pay special attention to the infor-
mation

Page 101 of 457

MERCEDES-BENZ G55AMG 2008 W463 Owners Manual 100 Controls in detail
In the “Controls in detail” section you will
find detailed information on how to oper-
ate the equipment installed in your vehicle.
If you are already familiar with the ba

Page 236 of 457

MERCEDES-BENZ G55AMG 2008 W463 Owners Manual 235
Controls in detail
Useful features
Call priority
If other service calls such as a Roadside
Assistance call or Information call are
active, an Emergency call is still possible.
In this case, the

235
Controls in detail
Useful features
Call priority
If other service calls such as a Roadside
Assistance call or Information call are
active, an Emergency call is still possible.
In this case, the Emergency call will take
priority and override all other active calls.
Remote door unlock
In case you have locked your vehicle unin-
tentionally (e.g. SmartKey inside vehicle),
and the reserve SmartKey is not handy:
Contact the Mercedes-Benz Response
Center at 1-800-756-9018 (in the USA)
or 1-888-923-8367 (in Canada).
You will be asked to provide your pass-
word which you provided when you
completed the subs
criber agreement.
Then return to your vehicle at the time
arranged with the Response Center
and press the tailgate lock for a
minimum of 20 seconds until the
SOS button is flashing.
The message
Connecting call
appears in the multifunction display.
As an alternative, you may unlock the vehi-
cle via Internet using the ID and password
sent to you shortly after the completion of
your acquaintance call.
!If the indicator lamps do not start flashing
after pressing one of the buttons or remain
illuminated (in red) at any time, the Tele Aid
system has detected a malfunction or the
service is not currently active, and may not
initiate a call. Visit your authorized
Mercedes-Benz Light Truck Center and have the
system checked or contact the Response Center
at 1-800-756-9018 (in the USA) or
1-888-923-8367 (in Canada) as soon as
possible.
iThe indicator lamp in the respective button
flashes until the call is concluded. Emergency
calls can only be terminated by a Response
Center or Customer Assistance Center repre-
sentative, whereas Roadside Assistance and
Information calls can also be terminated using
the t button on the multifunction steering
wheel or the END button on the COMAND
system headunit.
!If the indicator lamp continues to flash or
the system does not reset, contact the Response
Center at 1-800-756-9018 (in the USA) or
1-888-923-8367 (in Canada), or Mercedes-Benz
Customer Assistance at 1-800-FOR-MERCedes
(1-800-367-6372) in the USA or Customer
Service at 1-800-387-0100 in Canada.
W463.boo Seite 235 Montag, 19 . November 2007 8:41 08

Page 239 of 457

MERCEDES-BENZ G55AMG 2008 W463 Owners Manual 238 Controls in detail
Useful features
Step 2:
If you have previously programmed a
signal transmitter button and wish to
retain its programming, proceed to
step 3.
If you are programming the integ

238 Controls in detail
Useful features
Step 2:
If you have previously programmed a
signal transmitter button and wish to
retain its programming, proceed to
step 3.
If you are programming the integrated
remote control for the first time, press
and hold outer signal transmitter
buttons2 and 4 and release them
only when indicator lamp 1 begins to
flash after approximately 20 seconds
(do not hold the button for longer than
30 seconds). This procedure erases
any previous settings for all three
channels and initializes the memory.
If you later wish to program a second
and/or third hand-held transmitter to
the remaining two signal transmitter
buttons, do not repeat this step and
begin directly with step 3. Step 3:Hold end of hand-held remote
control
5 of the device you wish to
train approximately 2 to 5 in
(5 to12 cm) away from signal trans-
mitter button ( 2, 3 or 4) to be
programmed, while keeping indicator
lamp 1 in view.
Step 4:
Using both hands, simultaneously
press hand-held remote control
button 6 and the desired signal
transmitter button ( 2, 3 , or 4). Do
not release the buttons until step 5 is
completed.
Indicator lamp 1 will flash, first slowly
and then rapidly. Step 5:
After indicator lamp
1 changes from a
slow to a rapidly flashing light, release
the hand-held remote control button
and the signal transmitter button.
Step 6:
Press and hold the just-trained signal
transmitter button ( 2, 3 , or 4) and
observe indicator lamp 1.
If indicator lamp 1 stays on
constantly, programming is complete
and your device should activate when
the respective signal transmitter
button ( 2, 3 , or 4) is pressed and
released.
Step 7:
To program the remaining two signal
transmitter buttons, repeat the steps
above starting with step 3.
iIndicator lamp 1 flashes immediately the
first time the signal transmitter button is
programmed. If this button has already been
programmed, the indicator lamp will only start
flashing after 20 seconds.
iIf indicator lamp 1 flashes rapidly for about
2 seconds and then turns to a constant light,
continue with programming steps 8 through 12
as your garage door opener may be equipped
with the “rolling code” feature.

W463.boo Seite 238 Montag, 19 . November 2007 8:41 08

Page 241 of 457

MERCEDES-BENZ G55AMG 2008 W463 Owners Manual 240 Controls in detail
Useful features
If you live in Canada or if you are having
difficulties programming a gate operator
(regardless of where you live) by using the
programming procedures, replac

240 Controls in detail
Useful features
If you live in Canada or if you are having
difficulties programming a gate operator
(regardless of where you live) by using the
programming procedures, replace step 4
with the following:
Step 4:
Press and hold the signal transmitter
button (2,3 , or 4). Do not release
this button until it has been success-
fully trained.
While still holding down the signal
transmitter button ( 2, 3 or 4),
“cycle” your hand-held remote control
button 6 as follows: Press and hold
button 6 for 2 seconds, then release
it for 2 seconds, and again press and
hold it for 2 seconds. Repeat this
sequence on the hand-held remote
control until the frequency signal has
been learned. Upon successful train-
ing, indicator lamp 1 will flash slowly
and then rapidly after several seconds.
Proceed with programming step 5 and
step 6 to complete. Reprogramming a single signal
transmitter button
To program a device using a signal trans-
mitter button previously trained, follow
these steps:
Switch on the ignition (page 39).
Press and hold the desired signal
transmitter button (
2, 3 , or 4).
Do not release the button.
Indicator lamp 1 will begin to flash
after 20 seconds. Without releasing the
signal transmitter button, proceed with
programming starti ng with step 3. Operation of integrated remote control
Switch on the ignition (page 39).
Select and press the appropriate signal
transmitter button (
2, 3 , or 4) to
activate the remote controlled device.
The integrated remote control
transmitter continues to send the
signal as long as the button is
pressed – up to 20seconds.
Erasing the integrated remote control
memory
Switch on the ignition (page 39).
Simultaneously press and hold outer
signal transmitter buttons 2 and 4,
for approximately 20 seconds, until
indicator lamp 1 b l i n k s r a p i d l y . D o n o t
hold for longer than 30 seconds.
The codes of all three channels are
erased.
iUpon completion of programming the
integrated remote control, make sure you retain
the hand-held remote control that came with the
garage door opener, gate operator or other
device. You may need it for use in other vehicles,
for future programming of an integrated remote
control, or simply for continued use as a
hand-held remote control to operate the
respective device in other situations.
iIf you sell your vehicle, erase the codes of all
three channels.
W463.boo Seite 240 Montag, 19 . November 2007 8:41 08

Page 435 of 457

MERCEDES-BENZ G55AMG 2008 W463 Owners Manual 434 Index
D
Data recording (vehicle) 20
Daytime running lamp mode 119
Setting 151
Deactivating Air conditioning (cooling) 189
Air recirculation mode 189
Alarm 96
Anti-theft alarm system 96
Central loc

Page 436 of 457

MERCEDES-BENZ G55AMG 2008 W463 Owners Manual 435
Index
Driving on sand 259
Driving systems 197
Cruise control 197
Driving safety systems 87
Rear Parking Assist 200
Rear view camera 203
Rear view camera* 203
Driving through water 257
E
Easy-entry

Page 439 of 457

MERCEDES-BENZ G55AMG 2008 W463 Owners Manual 438 Index
Immobilizer 95Activating 95
Deactivating 95
Infant and child restraint systems 78 Installing 83
LATCH child seat anchors 82
Information button see Tele Aid
Inside rear view mirror Auto-dimmi

clutch set clock wheelbase service reset battery transmission fluid