420 Technical data
Fuels, coolants, lubricants, etc.
Capacities
Vehicle components and their respective
lubricants must match.Therefore only use
products tested and approved by
Mercedes-Benz.
Please refer to the Factory Approved
Service Products pamphlet (USA only), or
inquire at an authorized Mercedes-Benz
Light Truck Center.
Warning!G
Comply with all valid regulations with
respect to handling, storing and disposing
of service fluids. Otherwise you could
endanger persons or the environment.
Keep service fluids out of the reach of
children.
For health reasons, you should prevent
service fluids from coming into direct
contact with your skin or clothing.
If a service fluid is swallowed, contact a
physician immediately.
W463.boo Seite 420 Montag, 19. November 2007 8:41 08
423
Technical data
Fuels, coolants, lubricants, etc.
Engine oils
Engine oils are specifically tested for their
suitability in our engines and durability for
our service intervals. Therefore, only use
approved engine oils and oil filters
required for vehicles with Maintenance
System (U.S. vehicles) or FSS (Canada
vehicles). For a listing of approved engine
oils and oil filters, refer to the Factory
Approved Service Pr
oducts pamphlet
(USA only), or contact an authorized
Mercedes-Benz Light Truck Center.
Engine oil additives
Air conditioning refrigerant
R-134a (HFC) refrigerant and special PAG
lubricating oil are used in the air condition-
ing system.
Brake fluid
Only brake fluid approved by
Mercedes-Benz is recommended. Any
authorized Mercedes-Benz Light Truck
Center will provide you with additional
information.
!Using engine oils and oil filters of specifi-
cation other than those expressly required for
the Maintenance System (U.S. vehicles) or FSS
(Canada vehicles), or changing of oil and oil filter
at change intervals longer than those called for
by the Maintenance System (U.S. vehicles) or
FSS (Canada vehicles) will result in engine
damage not covered by the Mercedes-Benz
Limited Warranty. Please follow Maintenance System
(U.S. vehicles) or FSS (Canada vehicles)
recommendations for scheduled oil changes.
Failure to do so will result in engine damage not
covered by the Mercedes-Benz Limited
Warranty.
!Do not blend oil additives with engine oil.
They may damage the engine.
Damage or malfunctions resulting from blending
oil additives are not covered by the
Mercedes-Benz Limited Warranty.
!Never use R-12 (CFC) or mineral-based
lubricating oil. Otherwise damage to the system
will occur.
Warning!G
During vehicle operation, the boiling point of
the brake fluid is continuously reduced
through the absorption of moisture from the
atmosphere. Under extremely strenuous
operating conditions, this moisture content
can lead to the formation of bubbles in the
system, thus reducing the system’s
efficiency.
Therefore, the brake fluid must be replaced
regularly. Refer to your vehicle’s
Maintenance Booklet for replacement
interval.
W463.boo Seite 423 Montag, 19 . November 2007 8:41 08
425
Technical data
Fuels, coolants, lubricants, etc.
Gasoline additives
A major concern among engine
manufacturers is ca
rbon build-up caused
by gasoline. Mercedes-Benz recommends
only the use of quality gasoline containing
additives that prevent the build-up of car-
bon deposits.
After an extended period of using fuels
without such additives, carbon deposits
can build up, especially on the intake
valves and in the combustion area, leading
to engine performance problems such as:
Warm-up hesitation
Unstable idle
Knocking/pinging
Misfire
Power loss In areas where carbon deposits may be
encountered due to lack of availability of
gasolines which contain these additives,
Mercedes-Benz recommends the use of
additives approved by us for use on
Mercedes-Benz vehicles. Refer to the
Factory Approved Service Products
pamphlet (USA only) or
contact an autho-
rized Mercedes-Benz Light Truck Center
for a listing of approved product(s). Follow
directions on product label.
Do not blend other fuel additives with fuel.
This only results in unnecessary cost and
may be harmful to the engine operation.
Coolants
The engine coolant is a mixture of water
and anticorrosion/antifreeze, which
provides:
Corrosion protection
Freeze protection
Boiling protection (by increasing the
boiling point)
The cooling system was filled at the factory
with a coolant providing freeze protection
to approximately -35°F (-37°C) and corro-
sion protection.
If the antifreeze mixture is effective to
-35°F (-37°C), the boiling point of the cool-
ant in the pressurized cooling system is
reached at approxim ately 266°F (130°C).
!Damage or malfunction resulting from poor
fuel quality or from blending additional fuel
additives other than those tested and approved
by us for use on Mercedes-Benz vehicles are not
covered by the Mercedes-Benz Limited
Warranty.! Add premixed coolant solution only. Adding
water and MB 325.0 Anticorrosion/Antifreeze
separately from each other, could cause engine
damage not covered by the Mercedes-Benz
Limited Warranty.
W463.boo Seite 425 Montag, 19 . November 2007 8:41 08
426 Technical data
Fuels, coolants, lubricants, etc.
The coolant solution must be used year
round to provide the necessary corrosion
protection and increase boil-over protec-
tion. Refer to Maintenance Booklet for
replacement interval.
Coolant system design and coolant used
determine the replacement interval. The
replacement interval published in the
Maintenance Booklet is only applicable if
MB 325.0 Anticorrosion/Antifreeze
solution or other Mercedes-Bent approved
products of equal specification are used to
renew the coolant concen tration or bring it
back up to the proper level.
For information on other Mercedes-Benz
approved products of equal specification,
refer to the Factory Approved Service
Products pamphlet (USA only) or contact
an authorized Mercedes-Benz Light Truck
Center. To provide important corrosion protection,
the solution must be at least
50% anticorrosion/antifreeze (equivalent
to freeze protection to approximately
-35°F [-37°C]). If you use a solution that is
more than 55% anticorrosion/antifreeze
(freeze protection to approximately
-49°F [-45°C]), the engine temperature
will increase due to the lower heat transfer
capability of the so
lution. Therefore,
do not use more than this amount of
anticorrosion/antifreeze.
If the coolant level is low, water and
MB 325.0 Anticorrosion/Antifreeze
should be used to bring it up to the proper
level (have cooling system checked for
signs of leakage). Please make sure the
mixture is in accordance with label
instructions.
The water in the cooling system must meet
minimum requirements, which are usually
satisfied by normal drinking water. If you
are not sure about the water quality,
contact an authoriz ed Mercedes-Benz
Light Truck Center. Anticorrosion/antifreeze
Your vehicle contains a number of
aluminum parts. The use of aluminum
components in motor vehicle engines
necessitates that anticorrosion/antifreeze
coolant used in such engines be
specifically formulated to protect the
aluminum parts. Failure to use such
anticorrosion/antifreeze coolant will
result in a significantly shortened service
life.
Therefore, the followin
g product is strongly
recommended for use in your vehicle:
Mercedes-Benz
325.0 Anticorrosion/Antifreeze agent.
Before the start of the winter season (or
once a year in hot southern regions), you
should have the anticorrosion/antifreeze
concentration checked. The coolant is also
regularly checked each time you bring your
vehicle to an authorized Mercedes-Benz
Light Truck Center for service.
W463.boo Seite 426 Montag, 19 . November 2007 8:41 08
431
Index
Batteries
SmartKey (replacing) 374
Batteries, SmartKey Check lamp 103
Checking 103
Battery box Fuse box in 406
Battery discharged Jump starting 397
Battery, vehicle 394 Charging 396
Disconnecting 396
Messages in display 342–343
Reconnecting 396
Reinstalling 396
Removing 396
Bead 304
Block heater (Canada only) 310
Blocking rear door window operation 85
B-pillar 410
Brake fluid 266, 423 Message in display 344
Brake lamp bulbs, left and right 376
Brake lamp, high mounted 376
Brake lamps Messages in display 352 Brake pads
Message in display 345
Brakes 246 Warning lamp 326–327
Break-in period 244
Brush guard 373 Lowering 373
Raising and securing 373
Bulbs, replacing Additional turn signals 376
Backup lamps 376, 384
Brake lamps 376, 384
Front fog lamps 376, 380
Front lamps 376
Front turn signal lamps 376, 381
High beam lamps 376
High mounted brake lamp 376
License plate lamps 376, 385
Locator lighting lamps 376
Low beam lamps 376
Parking lamps 376, 378 Rear fog lamp 376, 384
Rear lamps 376
Rear turn signal lamps 376
Side marker lamps 376, 382
Standing lamps 376, 378
Tail lamp assemblies 376
Tail lamp unit 383
C
Call priority, Tele Aid 235
Calling up Maintenance service indicator display 313
Range (distance to empty) 158
Capacities Fuels, coolants, lubricants, etc. 420
Cargo area see Cargo compartment
Cargo compartment Expanding 206
Tailgate 105
Tie-down rings 209
Cargo compartment cover blind 214 Installing 214
Removing 214
Rolling out 214
Rolling up 214
Cargo compartment lamps 127
W463.boo Seite 431 Montag, 19 . November 2007 8:41 08
434 Index
D
Data recording (vehicle) 20
Daytime running lamp mode 119
Setting 151
Deactivating Air conditioning (cooling) 189
Air recirculation mode 189
Alarm 96
Anti-theft alarm system 96
Central locking (control system) 155
Cruise control 198
Defrost 188
ESP
®93
Exterior lamps 118
Exterior lamps delayed shut-off 153
Headlamps 64
Immobilizer 95
Interior lighting delayed shut-off 154
Rear window defroster 181
Tow-away alarm 97
Windshield defroster 181
Deep water see Standing water
Defrosting 187
Delayed shut-off Exterior lamps 153
Interior lighting 154 Department of Tran
sportation see DOT
Dialing A number (telephone) 160
Differential locks 173 Switching off 176
Switching on 175
Difficulties While driving see Problems while driv-ing
With starting 54
Direction of rotation (tires) 280
Discharged battery Jump starting 397
Disconnecting Vehicle battery 396
Displays Maintenance service indicator message 311
Messages 271, 336
Selecting display for status indicator 150
Showing vehicle status messages 145
Door Entry lamps 129
Remote door unlock (Tele Aid) 235 Door control panel 33
Door handle 33
Doors
Message in display 348
Opening from the inside 104
DOT 305
Downhill driving Cruise control 198
Drink holders see Cup holders
Drinking and driving 245
Driving General instructions 48, 245
In winter 251
Problems 61
Safety systems 87
Through standing water 252
Driving abroad 261
Driving and safety systems 4-ETS 90
ABS 87
BAS 89
EBB 91
ESP
®91
Driving instructions 245 Passenger compartment 252
Driving off 247
W463.boo Seite 434 Montag, 19 . November 2007 8:41 08
439
Index
Lamps in instrument cluster 324
Lamps, exterior
Front 376
Messages in display 352–357
Rear 376
Replacing bulbs for front 378
Replacing bulbs for rear 383
Lamps, indicator and warning ABS 324–325, 327
Battery (SmartKey) 102
Brakes 326–327
check engine 328–329
Engine diagnostics 328–329
ESP
®330–331
Fuel reserve 331
Instrument cluster 324–332
SRS 69, 332
Turn signals 27
Language Setting 149
LATCH child seat anchors 82
Layout of poly-V-belt drive 412
Leather upholstery Cleaning 322 License plate lamps
Messages in display 354
Replacing bulbs 376, 385
Lifting Vehicle 389
Light alloy wheels Cleaning 320
Technical data 415, 416
Light sensor Message in display 352
Lighter see Cigarette lighter
Lighting 117 Automatic headlamp mode 118
Combination switch 122
Daytime running lamp mode 119
Exterior lamp switch 117
Front fog lamps 121
High beam flasher 122
High beams 122
Instrument cluster illumination 130
Interior, front 125
Interior, rear 126
Locator lighting 120
Low beams 117
Manual headlamp mode 118
Night security illumination 120 Parking lamps 117
Rear fog lamp 121
Settings (control system) 151
Limiting gear range 168
Limp Home Mode 169
Loading 206 Cargo compartment cover blind 214
Cargo tie-down rings 209
Instructions 208
Partition net* 210
Roof rack 206
Loading terminology 304
Loading the vehicle 280
Locator lighting 120 Setting 152
Locator lighting lamps Replacing bulbs 376
Locking 62, 100 Fuel filler flap 264
Global, SmartKey 102
Vehicle in an emergency 369
Loss of keys 103
Loss of Service and Warranty Information Booklet 409
W463.boo Seite 439 Montag, 19 . November 2007 8:41 08
440 Index
Low beam headlampsMessages in display 354
Replacing bulbs 376
LOW RANGE - ABS 89
Lowering Vehicle 392
Lubricants Technical data 420
M
Main dimensions 418
Maintenance 311
Maintenance service Basic service (Service A) 311
Calling up the maintenance service in-dicator display 313
Extended service (Service B) 311
Overdue 313
Types 313
When due 311
Maintenance service indicator Calling up 313
Clearing 313 Maintenance service indicator display
Calling up 313
Maintenance service indicator message 311Clearing 312
Malfunction Displaying 145
Rear Parking Assist 203
Manual headlamp mode 118
Manual operation Interior lighting control 126
Manual operations Fuel filler flap 370
Locking the vehicle 369
Tilt/sliding sunroof 372
Unlocking gear selector lever 371
Unlocking the driver’s door 368
Unlocking the tailgate 369
Maximum load rating 305
Maximum loaded vehicle weight 305
Maximum tire inflation pressure 305
Mechanical key 368 Removing 368 Memory function 114
Recalling positions from memory 115
Storing exterior rear view mirror park- ing position (Canada only) 116
Storing key dependent settings 115
Menus 135 Audio 141
In control system 136, 137, 139
NAVI 144
Standard display 140
Submenus 135
TEL 159
Trip computer 157
Vehicle status message memory 144
Messages in the multifunction display 336Symbol messages 342–363
Text messages 338–341
Middle tunnel Fuse box in 405
Miles/kilometers in speedometer Setting 149
W463.boo Seite 440 Montag, 19 . November 2007 8:41 08