2008 MERCEDES-BENZ G500 jump cable

395
Practical hints
Battery
Warning!G
Failure to follow thes
e instructions can
result in severe injury or death.
Observe all safety instructions and precau-
tions when handling automotive batteries
(
page 394).
Never lean over batteries while connecting,
you might get injured.
Battery fluid contains sulfuric acid. Do not
allow this fluid to come in contact with eyes,
skin or clothing. In case it does, immediately
flush affected area with water and seek
medical help if necessary.
A battery will also pr oduce hydrogen gas,
which is flammable and explosive. Keep
flames or sparks away from battery, avoid
improper connection of jumper cables,
smoking, etc.
Warning!G
Jump starting must only be done using the
jump-start terminals located in the engine
compartment (
page 398).
Warning!G
Do not place metal objects on the battery as
this could result in a short circuit.
Use leak-proof battery only to avoid the risk
of acid burns in the event of an accident.
!Never loosen or detach battery terminal
clamps while the engine is running or the
SmartKey is in the starter switch. Otherwise the
alternator and other electronic components
could be severely damaged.
Have the battery checked regularly at an
authorized Mercedes-Benz Light Truck Center.
Refer to Maintenance Booklet for maintenance
intervals or contact an authorized
Mercedes-Benz Light Truck Center for further
information.
W463.boo Seite 395 Montag, 19 . November 2007 8:41 08

397
Practical hints
Jump starting
 Jump starting
If the battery is disc harged, the engine can
be started with jumper cables and the
battery of another vehicle. Observe the
following:

Jump starting should only be performed
using the jump-start terminals located
in the engine compartment
(
page 398).

Jump starting should only be performed
when the engine and catalytic
converter are cold.

Do not start the engine if the battery is
frozen. Let the battery thaw out first.

Only jump start from batteries with the
same voltage rating (12 V). Jump start-
ing with a higher voltage battery could
damage the vehicle’s electrical system,
which will not be covered by the
Mercedes-Benz Limited Warranty.

Only use jumper cables with sufficient
cross-section and insulated terminal
clamps.

Always make sure the jumper cables
are not on or near pulleys, fans, or
other parts that move when an engine
is started or running.
Warning!G
Failure to follow thes e directions will cause
damage to the electr onic components, and
can lead to a battery explosion and severe
injury or death.
Never lean over batteries while connecting
or jump starting, you might get injured.
Battery fluid contains sulfuric acid. Do not
allow this fluid to come in contact with eyes,
skin or clothing. In case it does, immediately
flush affected area with water, and seek
medical help if necessary.
A battery will also pr oduce hydrogen gas,
which is flammable and very explosive. Keep
flames or sparks away from battery, avoid
improper connection of jumper cables,
smoking, etc.
Attempting to jump start a frozen battery
can result in it explod ing, causing personal
injury.
Read all instructions before proceeding.
!Do not tow-start the vehicle.
!Avoid repeated and lengthy starting
attempts.
Do not attempt to start the engine using a
battery quick charge unit.
If the engine does not run after several unsuc-
cessful starting attempts, have it checked at the
nearest authorized Mercedes-Benz Light Truck
Center.
Excessive unburned fuel generated by repeated
failed starting attempts may damage the
catalytic converter.
Make sure the jumper cables do not have loose
or missing insulation.
Make sure the cable clamps do not touch any
other metal part while the other end is still
attached to a battery.
W463.boo Seite 397 Montag, 19 . November 2007 8:41 08

398 Practical hints
Jump starting
Make sure the two vehicles do not
touch.
Apply the parking brake (page 62).
Move the gear selector lever to park
positionP.
Turn off all electrical consumers.
Open the hood (page 267). The jump-start terminals are located on
the driver’s side of the engine compart-
ment.
1 Cover
2 Positive (+) terminal
3 Negative (-) terminal Open cover 1 of the positive terminal
of both vehicles.
Connect positive terminal 2 and the
positive terminal of the charged battery
with the jumper cable. Clamp the cable
to the charged battery first.
Start the engine of the vehicle with the
charged battery and run at idle speed.
Connect negative terminal 3 and the
negative terminal of the charged
battery with the jumper cable. Clamp
the cable to the charged battery first.
Start the engine of the disabled
vehicle.
You can now turn on the electrical con-
sumers. Do not switch on the headlamps
under any circumstances.
Remove the jumper cables first from
the negative terminals on each battery
and then from the positive terminals on
each battery.
You can now switch on the headlamps.
Have the battery checked at the
nearest authorized Mercedes-Benz
Light Truck Center.
Warning!G
Keep flames or sparks away from battery.
Do not smoke.
Observe all safety inst ructions and precau-
tions when handling automotive batteries
(
page 394).
!Never invert the terminal connections!
W463.boo Seite 398 Montag, 19 . November 2007 8:41 08

400 Practical hints
Towing the vehicle
Warning!G
With the engine not running, there is no
power assistance for the brake and steering
systems. In this case, it is important to keep
in mind that a considerably higher degree of
effort is necessary to brake and steer the
vehicle. Adapt your driving accordingly.
!Towing of the vehicle should only be done
using the towing eye. Never attach tow cable,
tow rope or tow rod to vehicle chassis, frame or
suspension parts.
iWhen towing the vehicle with all wheels on
the ground, note the following:
With the automatic central locking activated and
the SmartKey in starter switch position 2, the
vehicle doors lock if a wheel is turning at vehicle
speeds of approximately 9 mph (15 km/h) or
above.
To prevent the vehicle doors from locking,
deactivate the automatic central locking
(
page 155).
iTo signal turns while being towed with
hazard warning flasher in use, turn the SmartKey
in starter switch to position 2 and activate
combination switch for left or right turn signal in
usual manner – only the selected turn signal will
operate.
Upon canceling the turn signal, the hazard
warning flasher will operate again.
iThe gear selector lever will remain locked in
park position P and the SmartKey will not turn in
the starter switch if the battery is disconnected
or discharged. For more information, see “Bat-
tery” (
page 394) and “Jump starting”
(
page 397).
For information on manua lly unlocking the gear
selector lever, see (
page 371).
W463.boo Seite 400 Montag, 19 . November 2007 8:41 08