2008 MERCEDES-BENZ G500 high beam

25
At a glance
Cockpit
ItemPage
1Combination switch

High beam57

Turn signals57

Windshield wipers58
2Headlamp cleaning button177
3Cruise control lever197
4Horn
5Instrument cluster26
6Lever for Voice Control
System*, see separate
operating instructions
7Starter switch39
8Glove box release215
Glove box lock216
ItemPage
9Glove box215
aCenter console30
bMultifunction steering wheel28
cHood lock release267
dSteering wheel adjustment
stalk44
Heated steering wheel225
eExterior lamp switch56,
117
fExterior rear view mirror
adjustment46
W463.boo Seite 25 Montag, 19. November 2007 8:41 08

27
At a glance
Instrument cluster
ItemPage
1Speedometer with:
v
Electronic Stability Pro-
gram (ESP®) warning
lamp
91,
330
; Brake warning lamp,
USA only55,
326
3 Brake warning lamp,
Canada only55,
326
B Low beam headlamp in-
dicator lamp56,
118
H Low tire pres-
sure/TPMS malfunc-
tion telltale
1
1Depending on vehicle production date.
333
2LLeft turn signal
indicator lamp57
3Multifunction display with:133

Trip odometer131,
140
ItemPage

Main odometer140

Transfer case indicator170

Gear selector lever
position indicator164

Gear range indicator167

Status indicator:

Digital speedometer133

Outside temperature140

Clock133
4K Right turn signal
indicator lamp 57
5Tachometer with:
-Antilock Brake System
(ABS) indicator lamp87,
324
< Seat belt telltale74,
331
1 Supplemental
Restraint System
(SRS) indicator lamp68,
332
ItemPage
ú Engine malfunction
indicator lamp,
USA only328
±Engine malfunction
indicator lamp,
Canada only328
AHigh beam headlamp
indicator lamp57,
122
6Fuel gauge with:
Fuel tank reserve warning
lamp331
4 Fuel filler flap indica-
tor: The fuel filler flap
is located on the rear
right-hand side264
7Coolant temperature gauge131
8Reset button for:

Resetting trip odometer131

Resetting all settings146

Adjusting instrument
cluster illumination130
W463.boo Seite 27 Montag, 19. November 2007 8:41 08

39
Getting started
Unlocking
Press unlock button
Πon the
SmartKey.

All turn signal lamps flash once.

The locking knobs in the doors
move up.

The anti-theft alarm system is
disarmed.

The locator lighting comes on if the
feature is enabled in the control
system (
page 152).
Enter the vehicle and insert the
SmartKey in the starter switch.
For more information, see “Locking and
unlocking” (
page 100).
Starter switch positions
SmartKey
Starter switch
0 For removing SmartKey
The steering is locked when the
SmartKey is removed from the starter
switch.
1 Power supply for some electrical
consumers, such as seat adjustment
2 Ignition (power supply for all electrical
consumers) and driving position
All lamps (except high beam headlamp
indicator lamp and turn signal indicator
lamps unless activated) in the instru-
ment cluster come on. If a lamp in the
instrument cluster fails to come on
when the ignition is switched on, have
it checked and replaced if necessary. If
a lamp in the instrument cluster
remains on after starting the engine or
comes on while driving, refer to “Lamps
in instrument cluster” (
page 324).
3 Starting position
Warning!G
When leaving the vehicl e, always remove the
SmartKey from the starter switch, take it
with you, and lock the vehicle. Do not leave
children unattended in the vehicle, or with
access to an unlocked vehicle. A child’s
unsupervised access to a vehicle could
result in an accident and/or serious
personal injury.
W463.boo Seite 39 Montag, 19. November 2007 8:41 08

40 Getting started
Unlocking
For information on starting the engine, see
(
page 54).
iWhen you switch on the ignition, the indica-
tor and warning lamps (except high beam head-
lamp indicator lamp and turn signal indicator
lamps unless activated) in the instrument cluster
come on. The indicator and warning lamps
(except high beam headlamp indicator lamp and
turn signal indicator lamps if activated) will go
out when the engine is running. This indicates
that the respective systems are operational.
iThe SmartKey can only be removed from the
starter switch with the gear selector lever in park
position P.
iIf the SmartKey is left in starter switch
position 0 for an extended period of time, it can
no longer be turned in the switch. In this case,
the steering is locked. To unlock, remove
SmartKey from the starter switch and reinsert.
!If the SmartKey cannot be turned in the
starter switch, the battery may not be
sufficiently charged.

Check the battery and charge it if necessary
(
page 396).

Get a jump start (page 397).
To prevent accelerated vehicle battery discharge
or a completely discharged vehicle battery,
always remove the SmartKey from the starter
switch when the engine is not in operation.
W463.boo Seite 40 Montag, 19. November 2007 8:41 08

56 Getting started
Driving
After a cold start, the transmission shifts at
a higher engine revolution. This allows the
catalytic converter to reach its operating
temperature earlier.
For more information, see “Driving instruc-
tions” (
page 245).
For information on off-road driving, see
“Off-road driving” (
page 253).
Switching on headlamps
Low beam headlamps
The exterior lamp switch is located on the
dashboard to the left of the steering wheel.
Exterior lamp switch
1 Off
2 Low beam headlamps on
Turn the exterior lamp switch to
position B.
The low beam headlamp indicator
lamp B in the instrument cluster
comes on (
page 26).
iOnce the vehicle is in motion, the automatic
central locking system engages and the locking
knobs drop down.
The automatic door lock feature can be deacti-
vated (
page 155).
You can open a locked door from the inside.
Open door only when conditions are safe to do
so.
Warning!G
On slippery road surfaces, never downshift
in order to obtain braking action. This could
result in drive wheel slip and reduced vehi-
cle control. Your vehicle’s ABS will not pre-
vent this type of loss of control.
Warning!G
It is dangerous to shift the gear selector
lever out of P or N if the engine speed is
higher than idle speed. If your foot is not
firmly on the brake pedal, the vehicle could
accelerate quickl y forward or in reverse. You
could lose control of the vehicle and hit
someone or something. Only shift into gear
when the engine is idling normally and when
your right foot is firmly on the brake pedal.
!Do not run cold engine at high engine speed.
Running a cold engine at high engine speed may
shorten the service life of the engine.
!Simultaneously depressing the accelerator
pedal and applying the brakes reduces engine
performance and causes premature brake and
drivetrain wear.
W463.boo Seite 56 Montag, 19. November 2007 8:41 08

57
Getting started
Driving
High beam
The combination switch is located on the
left of the steering column.
Combination switch
1
High beam
2 High beam flasher
Push the combination switch in
direction of arrow 1.
The high beam headlamp indicator
lamp A in the instrument cluster
comes on (
page 26).
For more information on headlamps, see
“Lighting” (
page 117).
Turn signals
The combination switch is located on the
left of the steering column.
Combination switch
1 Turn signals, right
2 Turn signals, left
Press the combination switch in
direction of arrow 1 or 2.
The corresponding turn signal indicator
lamp K orL in the instrument
cluster flashes (
page 26).
The combination switch resets automati-
cally after major steering wheel move-
ments.
iTo signal minor directional changes such as
changing lanes, press co mbination switch only
to point of resistance and release. The corre-
sponding turn signals will flash three times.
W463.boo Seite 57 Montag, 19. November 2007 8:41 08

117
Controls in detail
Lighting
 Lighting
For information on how to switch on the
headlamps and use the turn signals, see
“Switching on headlamps” (
page 56)
and see “Turn signals” (
page 57).
Exterior lamp switch
The exterior lamp switch is located on the
dashboard to the left of the steering wheel.
iIf you drive in countries where vehicles drive
on the other side of the road than the country in
which the vehicle is registered, you must have
the headlamps modified for symmetrical low
beams. Relevant information can be obtained at
any authorized Mercedes-Benz Light Truck
Center.
1‚Standing lamps, left
(turn left two stops)
2ˆStanding lamps, right
(turn left one stop)
3MOff
Daytime running lamp mode
(
page 119)
4UAutomatic headlamp mode
Daytime running lamp mode
(
page 119)
5CParking lamps (also tail lamps,
license plate lamps, side mark-
er lamps, instrument panel
lamps)
6BLow beam headlamps or high
beam headlamps
7‡Front fog lamps
8†Rear fog lamp
iIf you hear a warning signal you have forgot-
ten to switch off the low beam headlamps or the
parking lamps before opening the driver’s door.
In addition the message
Switch off lights
appears in the multifunction display.
Switch off the low beam headlamps or the park-
ing lamps.
If the message
Turn off lights or remove
key
appears in the multifunction display remove
the SmartKey from the starter switch or switch
off the automatic headlamp mode.
!Failure to switch off the exterior lamps when
leaving the vehicle may result in a discharged
battery.
W463.boo Seite 117 Montag, 19 . November 2007 8:41 08

119
Controls in detail
Lighting
Turn the exterior lamp switch to
position
U.
With the SmartKey in starter switch
position 1, the tail and parking lamps,
the license plate lamps and the side
marker lamps will switch on and off de-
pending on the brightness of the ambi-
ent light.
When the engine is running the low
beam headlamps, the tail and parking
lamps, the license plate lamps and the
side marker lamps will switch on and
off depending on the brightness of the
ambient light. Daytime running lamp mode
In Canada the daytime running lamp mode
is mandatory and therefore in a constant
mode.
By default, the daytime running lamp mode
is deactivated. Activate the daytime
running lamp mode using the control
system, see “Setting daytime running lamp
mode (USA only)” (
page 151).
Turn the exterior lamp switch to
position
M orU .
When the engine is running, the low
beam headlamps are switched on.
In low ambient light conditions, the
following lamps will switch on
additionally:

Tail and parking lamps

License plate lamps

Side marker lamps Canada only:
When the engine is running, and you shift
from a driving position to neutral
position
N or park position P with the vehi-
cle at standstill, the low beam headlamps
will switch off with a 3-minute delay.
iCanada only:
High beam headlamps are only available with the
exterior lamp switch in position B.
iWith the daytime running lamp mode
activated and the engi ne running, you cannot
switch off the low beam headlamps manually.
iWith the exterior lamp switch in
position M orU , you cannot switch on the
high beam headlamps.
The high beam flasher is available at all times.
For nighttime driving turn the exterior lamp
switch to position B to permit activation of
the high beam headlamps.
W463.boo Seite 119 Montag, 19 . November 2007 8:41 08