2008 MERCEDES-BENZ CLS63AMG center console

150 Controls in detail
Control system
1Current CD (for CD changer)
2Current track
Press buttonk orj repeatedly
until the desired track is selected.Selecting MP3-CD track
Turn on COMAND and select CD or
CD changer*. Refer to separate
COMAND operating instructions.
Press buttonè orÿ repeatedly
until the settings for the MP3-CD cur-
rently being played appear in the multi-
function display.
1MP3 mode
2Current track
NAV* menu
The
NAV menu contains the functions
needed to operate your navigation system.
Press buttonè orÿ repeatedly
until the message
NAV appears in the
multifunction display.

If COMAND is switched off, the mes-
sage
NAV off is shown in the multi-
function display.

With COMAND switched on but route
guidance not activated, the direction of
travel and, if available, the name of the
street currently traveled on appear in
the multifunction display.

With COMAND switched on and route
guidance activated, the direction of
travel and maneuver instructions ap-
pear in the multifunction display.
Please refer to the COMAND manual for
instructions on how to activate the route
guidance system.
iTo select a CD from the CD changer maga-
zine, press a number on the COMAND system
key pad located in the center console.
iLevel of information displayed will vary de-
pending on the information contained on the
MP3-CD insert in the single CD player of the
COMAND system.
To select a MP3-CD from the CD changer maga-
zine, press a number on the COMAND system
key pad located in the center console.


169 Controls in detail
Automatic transmission
Automatic transmission
For more information on driving with an
automatic transmission, see “Automatic
transmission” (
page 51).
Your vehicle’s transmission adapts its gear
shifting process to your individual driving
style by continually adjusting the shift
points up or down. These shift point adjust-
ments are performed based on current
operating and driving conditions.
If the operating conditions change, the
automatic transmission reacts by
adjusting its shift program.
Gear selector lever
The gear selector lever is located on the
lower part of the center console.
Gearshift pattern for automatic
transmission
PPark position
RReverse gear
NNeutral
DDrive position
iDuring the brief warm-up, transmission
upshifting is delayed. This allows the catalytic
converter to heat up more quickly to operating
temperature.
Warning!G
Make sure that absolutely no objects are ob-
structing the pedals’ range of movement.
Keep the driver’s footwell clear of all obsta-
cles. If there are any floormats or carpets in
the footwell, make sure that the pedals still
have sufficient clearance.
During sudden driving or braking maneuvers
the objects could get caught between the
pedals. You could then no longer brake or
accelerate. This could lead to accidents and
injury.
iThe current gear selector lever positionP,
R,N orD appears in the multifunction display
(
page 171).

175 Controls in detail
Automatic transmission
Automatic shift program
The program mode selector switch is
located on the lower part of the center
console.
Program mode selector switch
C Comfort For comfort driving
S Sport For standard driving
Program mode selector switch
(CLS 63 AMG only)
M Manual For manual gear shifting
(
page 179)
C Comfort For standard driving
S Sport For sporty drivingThe selected program mode appears in the
multifunction display.
1Current program mode!Never change the program mode when the
gear selector lever is out of park positionP. This
could result in a change of driving characteristics
for which you may not be prepared.
iThe last selected program mode (CorS) is
switched on when the engine is restarted.

180 Controls in detail
Automatic transmission
The program mode selector switch is
located on the lower part of the center
console.
Program mode selector switch
M Manual For manual gear shifting
C Comfort For standard driving
S Sport For sporty driving
The selected program mode appears in the
multifunction display (
page 175).Activating manual shift program
Press program mode selector switch
repeatedly until the
M for manual pro-
gram modeM appears in the multifunc-
tion display.
The transmission switches to the
manual program modeM. Automatic
shifting is switched off. The gear range
is not limited.
You can change the gears manually when
the gear selector lever is in drive
positionD. You can upshift or downshift
through the gears in succession.Upshifting
Briefly press the gear selector lever to
the right in theD+direction.
or
Briefly pull right shift paddle2
(
page 178).
The transmission shifts to the next
higher gear.
If, instead of the manual program mode
symbol
M, thep symbol appears in the
multifunction display (
page 175), shift to
the next higher gear. The fuel supply will
otherwise be interrupted to prevent the
engine from overrevving.iFor information on automatic program
modesC orS, see “Automatic shift program”
(
page 175), “Gear selector lever one-touch
gearshifting” (
page 176), and “Steering wheel
gearshift control one-touch gearshifting*”
(
page 177).
iThe manual program modeM will not be
stored. When the engine is turned off with the
manual program modeM selected, the transmis-
sion will go to the automatic program mode
(CorS) when the engine is restarted.
!In the manual program modeM, the trans-
mission will not upshift, even if the engine has
reached its overrevving range. Shift up to the
next gear before the engine has reached its over-
revving range. Make absolutely certain that the
engine speed does not reach the red marking on
the tachometer (
page 26). Otherwise the
engine could be damaged which is not covered
by the Mercedes-Benz Limited Warranty.

185 Controls in detail
Good visibility
1Sun visor
2Mirror cover
3Mirror lamp
4Mounting
5Vanity mirror
Swing sun visors1 down when you
experience glare.
To use the vanity mirror5, lift up the
mirror cover2.
Make sure the sun visor is properly
engaged in the mounting4.
Lamp3 switches on.If sunlight enters through a side window:
Disengage sun visor1 from
mounting4.
Pivot sun visor to the side.
Rear window sunshade*
The switch is located in the center console.
1Rear window sunshade switch
Switch on the ignition (page 38).
Press switch1 briefly to raise the sun-
shade.
Press switch1 briefly to lower the
sunshade.
Always raise the sunshade fully for its sup-
port against the window frame.
iIf sun visor1 is disengaged from
mounting4 with mirror cover2 open, mirror
lamp3 will switch off.


202 Controls in detail
4-zone automatic climate control
Activating
Switch off the ignition.
Press buttonT (page 191).
REST in display4 (page 191) comes
on.
Deactivating
Press buttonT (page 191) again.
REST in display4 (page 191) goes
out.
Rear climate control
The rear climate control is adjusted via the
front climate control panel (
page 190) or
(
page 191) or the rear climate control
panel.
The rear climate control panel is located in
the rear center console.
iHow long the system will provide heating de-
pends on

the coolant temperature

the temperature set by the operator
The blower will run at speed setting1 regardless
of the air distribution control setting.
iThe residual heat is automatically turned off:

when the ignition is switched on

after about 30 minutes

if the battery voltage drops

if the coolant temperature is too low
1Left rear center air vent, adjustable
2Right rear center air vent, adjustable
3Thumbwheel for air volume control
for right rear center air vent
4Temperature rocker switch, right
5Display
6Temperature rocker switch, left
7Thumbwheel for air volume control
for left rear center air vent

204 Controls in detail
4-zone automatic climate control
Set the desired temperature for the
rear passenger compartment using the
temperature rocker switches
(
page 190) or (page 191).
After approximately 5 seconds after
the last adjustment, the display switch-
es back to its standard display.Front center console storage compart-
ment ventilation
The front center console storage compart-
ment under the armrest has its own air
vent. The air temperature is about the
same as that of the dashboard air vents.
The lever is located in the front center
vent.
1Lever
To open air vent slide the lever1 up.
To close air vent slide the lever1
down.
iYou can also press button™ or5
(
page 190) or (page 191) once more to
switch back to the standard display.
iThe compartment can get very warm due to
its confined space. When storing heat sensitive
objects (e.g. groceries) in the compartment,
close the air vent while heating the passenger
compartment.

226 Controls in detail
Driving systems
Setting the following distance in
Distronic
You can set the specified following dis-
tance for Distronic by varying the time set-
ting between 1.0 and 2.0 seconds. Using
this time setting and the current speed of
your vehicle, Distronic calculates and sets
the required following distance to the vehi-
cle ahead. The set distance will be shown
in the multifunction display field.
The thumbwheel for making the time set-
ting is located on the lower section of the
center console.1Distance warning function on/off
switch
2Indicator lamp
3Thumbwheel for setting distance
Increasing distance
Increasing the distance setting tells
Distronic to maintain a greater following
distance to the vehicle ahead.
Turn thumbwheel3 towards¯.Decreasing distance
Decreasing the distance setting tells
Distronic to maintain a shorter following
distance to the vehicle ahead.
Turn thumbwheel3 towards®.
Distance warning function
When Distronic is deactivated, this func-
tion will continue to warn you when recog-
nizing a stationary obstacle or a slower
vehicle moving in the vehicle’s path and
the danger of a collision exists:

The distance warning lampl in the
instrument cluster comes on.

An intermittent warning will sound if
necessary.
If these warnings are issued, you must
brake manually to maintain a safe distance
and avoid a collision with the vehicle
ahead.Warning!G
It is up to the driver to exercise discretion to
select the appropriate setting given road
conditions, traffic, driver’s preferred driving
style and applicable laws and driving recom-
mendations for safe following distance.