2008 MERCEDES-BENZ CLS63AMG buttons

265 Controls in detail
Useful features
Rolling code programming
To train a garage door opener (or other
rolling code devices) with the rolling code
feature, follow these instructions after
completing the “Programming” portion
(steps 1 through 6) of this text. (A second
person may make the following training
procedures quicker and easier.)
Step 8:
Locate “training” button on the garage
door opener motor head unit.
Exact location and color of the button
may vary by garage door opener brand.
Depending on manufacturer, the
“training” button may also be referred
to as “learn”or “smart” button. If there
is difficulty locating the transmitting
button, refer to the garage door opener
operator’s manual.
Step 9:
Press the “training” button on the ga-
rage door opener motor head unit.
The “training light” is activated.You have 30 seconds to initiate the follow-
ing two steps.
Step 10:
Return to the vehicle and firmly press,
hold for 2 seconds and release the pro-
grammed signal transmitter button
(2, 3 or4).
Step 11:
Press, hold for 2 seconds and release
same signal transmitter button a sec-
ond time to complete the training pro-
cess.
Step 12:
Confirm the garage door operation by
pressing the programmed signal trans-
mitter button (2, 3 or4).Step 13:
To program the remaining two signal
transmitter buttons, repeat the steps
above starting with step 3.
Gate operator/Canadian programming
Canadian radio-frequency laws require
transmitter signals to “time-out” (or quit)
after several seconds of transmission
which may not be long enough for the
integrated signal transmitter to pick up the
signal during programming. Similar to this
Canadian law, some U.S. gate operators
are designed to “time-out” in the same
manner.
If you live in Canada or if you are having
difficulties programming a gate operator
(regardless of where you live) by using the
programming procedures, replace step 4
with the following:
iSome garage door openers (or other rolling
code equipped devices) may require you to
press, hold for 2 seconds and release the same
signal transmitter button a third time to com-
plete the training process.

266 Controls in detail
Useful features
Step 4:
Press and hold the signal transmitter
button (2, 3 or4). Do not release
this button until it has been successful-
ly trained.
While still holding down the signal
transmitter button (2, 3 or4),
“cycle” your hand-held remote control
button6 as follows: Press and hold
button6 for 2 seconds, then release
it for 2 seconds, and again press and
hold it for 2 seconds. Repeat this se-
quence on the hand-held remote con-
trol until the frequency signal has been
learned. Upon successful training, indi-
cator lamp1 will flash slowly and then
rapidly after several seconds.
Proceed with programming step 5 and
step 6 to complete.Reprogramming a single signal trans-
mitter button
To program a device using a signal trans-
mitter button previously trained, follow
these steps:
Switch on the ignition (page 38).
Press and hold the desired signal
transmitter button (2, 3 or4).
Do not release the button.
Indicator lamp1 will begin to flash af-
ter 20 seconds. Without releasing the
signal transmitter button, proceed with
programming starting with step 3.Operation of integrated remote control
Switch on the ignition (page 38).
Select and press the appropriate inte-
grated signal transmitter button (2,
3 or4) to activate the remote con-
trolled device.
The integrated remote control trans-
mitter continues to send the signal as
long as the button is pressed – up to
20 seconds.
Erasing integrated remote control
memory
Switch on the ignition (page 38).
Simultaneously press and hold outer
signal transmitter buttons2 and 4,
for approximately 20 seconds, until
indicator lamp1 flashes rapidly. Do
not hold for longer than 30 seconds.
The codes of all three channels are
erased.
iUpon completion of programming the inte-
grated remote control, make sure you retain the
hand-held remote control that came with the ga-
rage door opener, gate operator or other device.
You may need it for use in other vehicles, for fu-
ture programming of an integrated remote con-
trol, or simply for continued use as a hand-held
remote control to operate the respective device
in other situations.
iIf you sell your vehicle, erase the codes of all
three channels.

471 Index
Service and warranty information 10
Service intervals see Maintenance, Service
indicator
Service life
Tires 294
Service see Maintenance
Service system see Maintenance
system 330
Service, Parts 432
Settings 106, 152
Control system menus and
submenus 141
Date 158
Individual, Vehicle 152
Memory function 124
Resetting all, Control system 153
Selective, SmartKey 102
Selective, SmartKey with
KEYLESS-GO* 107
Suspension tuning 230
Temperature (interior) 195
Time 157
Settings menu
Functions in 152
Submenus 153
Shelf below rear window, cleaning 340Shift program mode, Automatic
transmission 175
Shifting, Automatic transmission 169
Side impact air bags 70
Side marker lamps
Cleaning lenses 337
Side windows
Synchronizing power windows 207
Side windows see Power windows
Sidewall 325
Ski bag* (Canada only) 239
SmartKey see Key, SmartKey
SmartKey with KEYLESS-GO* see Key,
SmartKey with KEYLESS-GO*
Snow chains 329
Snow tires 328
Spare wheel 393, 445
Mounting 412
Speed settings
Cruise control 213
Distronic* 223
Speedometer 27
Selecting display mode 155
SRS 64
Indicator lamp 27, 353
Messages in display 388Standing lamps 126
Standing water, Driving through 279
Starter switch 38
Starter switch positions 38
Starting difficulties 52
Starting the engine
SmartKey 51
SmartKey with KEYLESS-GO* 52
Steering wheel 28
Adjustment 44
Buttons 28
Cleaning 340
Steering wheel gearshift control one-touch
gearshifting*
Automatic transmission 177
Stolen Vehicle Recovery services 262
Storage compartments 32, 243
Center armrest 243
Cup holder 246
Glove box 243
Parcel net in front passenger
footwell 245
Rear armrest 244
Rear center console 244
Ruffled storage bags 245
Under seat 244