2008 MERCEDES-BENZ CLK63AMG rear view mirror

127 Controls in detail
Memory function
Memory function
Prior to operating the vehicle, the driver
should check and adjust the seat height,
seat position fore and aft, and seat back-
rest angle if necessary, to ensure adequate
control, reach and comfort. The head
restraint should also be adjusted for
proper height. See also the section on
air bags (
page 65) for proper seat
positioning.
In addition, adjust the steering wheel to
ensure adequate control, reach, operation
and comfort. Both the interior and exterior
rear view mirrors should be adjusted for
adequate rear vision.
Fasten seat belts. Infants and small chil-
dren should be seated in a properly se-
cured restraint system that complies with
U.S. Federal Motor Vehicle Safety
Standards 213 and 225 and
Canadian Motor Vehicle Safety Standards
213 and 210.2.With the memory function you can store up
to three different configuration.
Each stored position on the driver’s side
includes the following settings:

Seat position

Steering wheel position

Exterior rear view mirror position

Multicontour seat*: previously saved
settingEach stored position on the passenger side
includes the following setting:

Seat position
Warning!G
Do not activate the memory function while
driving. Activating the memory function
while driving could cause the driver to lose
control of the vehicle.

128 Controls in detail
Memory function
The memory button and memory position
switch are located on the door.
1Memory button
2Memory position switch
Switch on the ignition (page 40).
or
Open the respective door and insert
the SmartKey in the starter switch.
Storing positions into memory
Adjust the seats, steering wheel and
exterior rear view mirrors to the
desired position (
page 42).
Turn memory position switch2 to the
desired memory position.
Press memory button1.
Release memory button1 and press
memory position switch2 within
3 seconds.
All settings are stored to the selected
position.
Recalling positions from memory
Turn memory position switch2 to the
desired memory position.
Press and hold memory position
switch2 until the seat, steering wheel
and exterior rear view mirrors have
completely moved to the stored
positions.
!Do not operate the seats using the memory
button if the seat backrest is in an excessively re-
clined position. Doing so could cause damage to
front or rear seats.
First move the seat backrest to an upright
position.
iReleasing the memory position switch stops
movement to the stored positions immediately.

185 Controls in detail
Good visibility
Good visibility
For information on the windshield wipers,
see “Windshield wipers” (
page 56).
Headlamp cleaning system*
The button is located on the left side of the
dashboard.
1Headlamp washer button
Switch on the ignition (page 40).
Press button1.
The headlamps are cleaned with a
high-pressure water jet.For information on filling up the washer
reservoir, see “Windshield washer system
and headlamp cleaning system*”
(
page 496).
Rear view mirrors
For more information on setting the rear
view mirrors, see “Mirrors” (
page 47).
Interior rear view mirror, antiglare
position
1Lever
Tilt the mirror to the antiglare position
by moving lever1 towards the wind-
shield.
The interior rear view mirror is dimmed.
iThe headlamps will automatically be
cleaned when you have

switched on the headlamps
and

operated the windshield wipers with wind-
shield washer fluid fifteen times
When you switch off the ignition, the counter
resets.

186 Controls in detail
Good visibility
Auto-dimming rear view mirrors*
The reflection brightness of the exterior
rear view mirror on the driver’s side and
the interior rear view mirror will respond
automatically to glare when

the ignition is switched on (page 40),
and

incoming light from headlamps falls on
the sensor in the interior rear view
mirror.
The rear view mirror will not react if

reverse gearR is engaged

the interior lighting is turned on
Warning!G
The auto-dimming function does not react if
incoming light is not aimed directly at sen-
sors in the interior rear view mirror.
The interior rear view mirror and the exterior
rear view mirror on the driver’s side do not
react, for example, if the rear window sun
shade* is in raised position, or if the wind
screen is installed.
Light hitting the mirror(s) at certain angles
(incident light) could blind you. As a result,
you may not be able to observe traffic con-
ditions and could cause an accident.
Warning!G
Exercise care when using the passen-
ger-side exterior rear view mirror. The mirror
surface is convex (outwardly curved surface
for a wider field of view). Objects in mirror
are closer than they appear. Check your
interior rear view mirror or glance over your
shoulder before changing lanes.

296 Controls in detail
Useful features
Emergency calls
An emergency call is initiated
automatically following an accident in
which the emergency tensioning devices
(ETDs) or air bags deploy.
An emergency call can also be initiated
manually by opening the cover next to the
interior rear view mirror labeled SOS, then
briefly pressing the button located under
the cover. See (
page 297) for
instructions on initiating an emergency call
manually.
Once the emergency call is in progress, the
indicator lamp in the SOS button will begin
to flash. The message
Connecting Call
appears in the multifunction display and
the audio system is muted. When the
connection is established, the message
Call Connected appears in the multifunc-
tion display. All information relevant to the
emergency, such as the location of the
vehicle (determined by the GPS satellite
location system), vehicle model, identifica-
tion number and color are generated.A voice connection between the Response
Center and the occupants of the vehicle
will be established automatically soon af-
ter the emergency call has been initiated.
The Response Center will attempt to
determine more precisely the nature of the
emergency provided they can speak to an
occupant of the vehicle.
The Tele Aid system is available if:

it has been activated and is
operational. Activation requires a
subscription for monitoring services,
connection and cellular air time

the relevant cellular phone network
and GPS signals are available and pass
the information on to the Response
Center
Warning!G
If the indicator lamps in the SOS button, in
the Roadside Assistance button and/or in
the Information button remain illuminated
constantly in red and/or message
Tele Aid Inoperative is displayed in the
multifunction display after the system
self-check, a malfunction in the system has
been detected.
If a malfunction is indicated as outlined
above, the system may not operate as
expected. Have the system checked at the
nearest Mercedes-Benz Center as soon as
possible.
iLocation of the vehicle on a map is only pos-
sible if the vehicle is able to receive signals from
the GPS satellite network and pass the informa-
tion on to the Response Center.

302 Controls in detail
Useful features
Interior rear view mirror with integrated re-
mote control
1Indicator lamp
2 3 4Signal transmitter button
Needed for programming (not part of
vehicle equipment):
5Hand-held remote control of ga-
rage door opener, gate operator
or other device
6Hand-held remote control
buttonProgramming the integrated remote
control
Step 1:
Switch on the ignition (page 40).
Step 2:
If you have previously programmed a
signal transmitter button and wish to
retain its programming, proceed to
step 3.
If you are programming the integrated
remote control for the first time, press
and hold the two outer signal transmit-
ter buttons2 and4 and release
them only when indicator lamp1
Warning!G
Before programming the integrated remote
control to a garage door opener or gate
operator, make sure people and objects are
out of the way of the device to prevent po-
tential harm or damage. When programming
a garage door opener, the door moves up or
down. When programming a gate operator,
the gate opens or closes.
Do not use the integrated remote control
with any garage door opener that lacks
safety stop and reverse features as required
by U.S. federal safety standards (this
includes any garage door opener model
manufactured before April 1, 1982).
A garage door that cannot detect an object
– signaling the door to stop and reverse –
does not meet current U.S. federal safety
standards.
When programming a garage door opener,
park outside the garage.
Do not run the engine while programming
the integrated remote control. Inhalation of
exhaust gas is hazardous to your health. All
exhaust gas contains carbon monoxide
(CO), and inhaling it can cause unconscious-
ness and possible death.

370 Operation
Vehicle care
Soft top (CLK cabriolet)
Frequent cleaning reduces the
dirt-repellent effect of the soft top.
Intensive cleaning with Mercedes-Benz
car-care products for convertible soft tops
can help to restore the dirt-repellent
effect. Contact an authorized
Mercedes-Benz Center for detailed
information.
Light colored soft tops should be cleaned
frequently to prevent spots and dirt from
setting in, which could stain and discolor
the soft top material permanently.
Incorrect cleaning and care, as well as
ageing, can cause the soft-top seams to
leak. Have the soft-top seams sealed at a
Mercedes-Benz Center.!Make sure the windshield wiper switch is
set to0 (
page 56). Otherwise, e.g. the rain
sensor could activate and cause the wipers to
move unintentionally. This may lead to vehicle
damage.
Due to the width of the vehicle, fold in exterior
rear view mirrors prior to running the vehicle
through an automatic car wash to prevent
damage to the mirrors.
iAfter running the vehicle through an
automatic car wash, wipe any wax off of the
windshield (
page 373). This will prevent
smears and reduce wiping noise which can be
caused by residual wax on the windshield.
When leaving the car wash, make sure the mir-
rors are folded out. Otherwise they may vibrate.
iIf the soft top is kept in the storage
compartment for a lengthy period, raise it and air
out with the windows open about every
4months.
Place a suitable cover over the soft top if you are
leaving the vehicle parked in the open for an
extended period of time.
!Remove bird droppings immediately. The
organic acid damages the material and causes
the soft top to leak.
Never use a power washer to clean the soft top,
as you may damage the soft top material.
Do not use sharp-edged instruments for the
removal of ice and snow.
Never use hot-wax when you run the vehicle
through an automatic car wash, as you may
damage the soft top material.

415 Practical hints
What to do if …?
Display symbolDisplay messagePossible cause/consequencePossible solution
. Tail Lamp
Right
Auxiliary Bulb On

The right tail lamp is malfunctioning. A
backup bulb is being used.Replace the bulb as soon as possible
(
page 448).
Left Mirror
Turn SignalThe turn signal in the left exterior rear
view mirror is malfunctioning. This mes-
sage will only appear if a critical number
of LEDs have stopped working.Contact an authorized Mercedes-Benz
Center as soon as possible.
Right Mirror
Turn SignalThe turn signal in the right exterior rear
view mirror is malfunctioning. This mes-
sage will only appear if a critical number
of LEDs have stopped working.Contact an authorized Mercedes-Benz
Center as soon as possible.
Turn Signal
Rear Left
Auxiliary Bulb On

The left rear turn signal lamp is malfunc-
tioning. A backup bulb is being used.Replace the bulb as soon as possible
(
page 448).
Turn Signal
Rear Right
Auxiliary Bulb On

The right rear turn signal lamp is malfunc-
tioning. A backup bulb is being used.Replace the bulb as soon as possible
(
page 448).