2008 MERCEDES-BENZ CLK550 trunk

436 Practical hints
Opening/closing in an emergency (Cabriolet)
You and your assistant should each
take one of the straps by the handle.
With a strong, simultaneous tug on the
loops, pull soft top compartment cover
upward and out to the rear.9Soft top compartment cover
One person should stand on the left
side of the vehicle and the other on the
right side.
Pulling the cover back in one smooth
motion, lift soft top compartment
cover9 into a vertical position until it
stops.
Warning!G
In the next step, you and your assistant
should each take hold of the soft top com-
partment cover as shown in the illustration.
Both of you should use your free hand to
support yourselves on the edge of the trunk
lid as shown in the illustration.
If either you or your helper assume a differ-
ent position, one or both of you could be
trapped or injured.
!Make sure the soft top storage compart-
ment hinges do not fold down during this proce-
dure. Otherwise your vehicle could be damaged.


437 Practical hints
Opening/closing in an emergency (Cabriolet)
aEdge of soft top
From left and right sides, reach into
soft top compartment underneath
edge of soft topa.bWindshield frameLift soft top out of soft top compart-
ment and pull it forward to windshield
frameb.cOpening
dLockingTake off protective cap on the inner
side of the soft top.
Insert hex wrench into soft top locking
mechanism screw.
Turn the soft top locking mechanism
screw with hex wrench clockwise in di-
rection of arrowc as far as it will go.
The clasp will open and the soft top will
engage audibly.
Warning!G
Do not place your hands near the upper
windshield area, trunk lid, or between soft
top roof panels and hinges while the soft top
is being raised and locked. Serious personal
injury may occur.


439 Practical hints
Opening/closing in an emergency (Cabriolet)
You and your assistant should press
soft top compartment cover f for-
ward and down with the palms of your
hands until it snaps into place in the
guide. Place your hands on the areas
indicated by the arrows.
At the same time, gently press material
tensioning framee down with the
palms of your hands.
hLocking
Insert hex wrench into soft top locking
mechanism screw.
Turn the soft top locking mechanism
screw with hex wrench counterclock-
wise in direction of arrowh as far as it
will go.
The soft top is locked onto the wind-
shield frame.
Have the soft top operation checked at
an authorized Mercedes-Benz Center
as soon as possible.
Warning!G
Position hands as indicated by arrows so
that when you press soft top compartment
coverf forward and lower material ten-
sioning framee, your hands cannot be-
come trapped.
!Make sure you turn the hex wrench counter-
clockwise as far as it will go. Otherwise the soft
top may not lock properly.
!If, after completing the soft top emergency
operation, the trunk cannot be opened using the
remote trunk lid release switch in the driver’s
door, theŠ button on the SmartKey, or the
trunk lid release handle in the license plate re-
cess, press the soft top compartment cover
down again as described above.
Do not open the trunk with the emergency key,
as this could otherwise damage the trunk lid and
the soft top compartment cover.

448 Practical hints
Replacing bulbs
Reinsert bulb holder4 w i t h t h e b u l b i n
the lamp and turn clockwise.
Align housing cover2 and turn it
clockwise.
Front turn signal lamp bulb
Turn bulb socket1 counterclockwise
and remove it.
Press gently onto the bulb and turn
counterclockwise out of bulb
socket1.
Press the new bulb gently into bulb
socket1 and turn clockwise until it
engages.
Place bulb socket1 back into the
lamp and turn it clockwise.
Parking and standing lamp bulb
Turn housing cover2 counterclock-
wise and remove it.
Pull out bulb socket5 with the bulb.
Pull the bulb out of the bulb socket5.
Press the new bulb into bulb socket5.
Press bulb socket5 back into the
lamp.
Align housing cover2 and turn it
clockwise.
Additional turn signal lamps
The additional turn signal lamps in the ex-
terior rear view mirrors have LEDs.
If a malfunction occurs or LEDs fail to func-
tion, the entire turn signal unit must be re-
placed. Have the additional turn signal unit
replaced at an authorized Mercedes-Benz
Center.
Front side marker lamp
Since replacing the side marker lamp bulbs
is a technically highly demanding process,
we recommend you have the side marker
lamp bulbs replaced at an authorized
Mercedes-Benz Center.
Replacing bulbs for rear lamps
Before you start to replace a bulb for a rear
lamp, do the following first:
Turn the exterior lamp switch to
positionM (
page 129).
Tail lamp unit
Open trunk lid.
Swing the trim panel covering the
corresponding rear lights to the side.
1Connector
2Tab
Disconnect electrical connector1.


453 Practical hints
Flat tire
Foreign objects (e.g. screws or nails)
should not be removed from the tire.
Take TIREFIT, the sticker, and the
electric air pump out of the trunk
(
page 422).
Two-part sticker
1Sticker for instrument cluster
2Sticker for wheel
Attach sticker part 1 where it will be
easily seen by the driver on the instru-
ment cluster.
Attach sticker part 2 to the damaged
tire (close to the tire valve).
Warning!G
Take care not to allow the contents of
T I R E F I T t o c o m e i n c o n t a c t w i t h h a i r , e y e s o r
clothing. TIREFIT is harmful if inhaled,
swallowed or absorbed through the skin -
causes skin, eye and respiratory irritation.
Any contact with eyes or skin should be
flushed immediately with plenty of water.
If clothing comes in contact with TIREFIT,
change clothing as soon as possible.
In case of allergic reaction or rash, consult a
physician immediately.
Warning!G
Keep TIREFIT out of reach of children.
If swallowed, rinse mouth immediately with
plenty of water and drink plenty of water.
Do not induce vomiting!
Consult a physician immediately.
Keep away from open flame or heat source.
iIf sealant has leaked out, let it dry. You can
then peel it off.
Warning!G
Observe safety instructions on air pump
label.
iYour vehicle may be equipped with either of
two versions of the electric air pump:

Version 1
The air hose with pressure gauge and the
electrical plug are located behind a flap.

Version 2
The pressure gauge is located in the pump
housing.
The following description applies to both
versions. Differences in usage are expressly
declared.

456 Practical hints
Flat tire
After attaining a tire inflation pressure
of 26 psi (1.8 bar), press0 on electric
air pump switch3 (
page 454).
The electric air pump is switched off.
Turn the SmartKey in the starter switch
to position0 (
page 38).
Vehicles with KEYLESS-GO*:
Press the KEYLESS-GO* start/stop
button (
page 40) on the gear
selector lever twice. Do not depress
brake pedal.
Detach the electric air pump.
The air hose may still be hot. Please
exercise appropriate caution.
Place the electrical air pump back in
the trunk.
Close the trunk.
Drive off immediately.
The TIREFIT sealant will distribute itself
evenly inside the tire.
After driving the vehicle for an initial
10 minutes, check the tire inflation
pressure using pressure gauge b on
the air pump.
Warning!G
If a tire inflation pressure of 26 psi (1.8 bar)
is not attained, the tire is too severely
damaged for TIREFIT to provide a reliable
tire repair.
In this case, TIREFIT cannot properly seal
the tire.
Do not drive the vehicle.
Contact the nearest Mercedes-Benz Center
or call Roadside Assistance.
Warning!G
Do not exceed vehicle speed of
50 mph (80 km/h). A TIREFIT repair is not
designed to operate at higher speeds.
The sticker must be attached on the instru-
ment cluster where it will be easily seen by
the driver.
Vehicle handling characteristics of a TIREFIT
repaired tire may change. Adapt your driving
accordingly.


458 Practical hints
Flat tire
Drive to the nearest qualified work-
shop, e.g. an authorized
Mercedes-Benz Center, to have the
damaged tire replaced.
Recommended duration of use:
A maximum of 300 miles (500 km) at
50 mph (80 km/h) or below with the
recommended tire inflation pressure.
Contact an authorized Mercedes-Benz
Center as soon as possible to obtain a
new TIREFIT kit.
Bring used TIREFIT materials to an
authorized Mercedes-Benz Center for
proper disposal.
Replace your TIREFIT container every
4 years. Replacement containers are
available at your authorized
Mercedes-Benz Center.
Mounting the Minispare wheel Preparing the vehicle
Prepare the vehicle as described
(
page 452).
Take the wheel wrench, alignment bolt,
collapsible wheel chock, and the jack
out of the trunk (
page 422).
Take the Minispare wheel and wheel
bolts out of the trunk (
page 425).
Warning!G
The dimensions of the Minispare wheel is
different from those of the road wheels. As
a result, the vehicle handling characteristics
change when driving with a Minispare wheel
mounted. Adapt your driving style
accordingly.
The Minispare wheel is for temporary use
only. When driving with a Minispare wheel
mounted, ensure proper tire pressure and
do not exceed a vehicle speed of 50 mph
(80 km/h).
Drive to the nearest Mercedes-Benz Center
as soon as possible to have the Minispare
wheel replaced with a regular road wheel.
Never operate the vehicle with more than
one Minispare wheel mounted.
Do not switch off the ESP
® when a
Minispare wheel is mounted.


461 Practical hints
Flat tire
Mounting the Minispare wheel
1Wheel bolt for light alloy rims
2Wheel bolt for Minispare wheel,
(located in trunk with Minispare wheel)Clean contact surfaces of wheel and
wheel hub.
1Alignment bolt
Guide spare wheel onto the alignment
bolt and push it on.
Insert wheel bolts and tighten them
slightly.!Wheel bolts2 must be used when mount-
ing the Minispare wheel. The use of any wheel
bolts other than wheel bolts2 for the Minispare
wheel will physically damage the vehicle’s
brakes.
!To avoid paint damage, place wheel flat
against hub and hold it there while installing first
wheel bolt.
Warning!G
Always replace wheel bolts that are
damaged or rusted.
Never apply oil or grease to wheel bolts.
Damaged wheel hub threads should be
repaired immediately. Do not continue to
drive under these circumstances! Contact
an authorized Mercedes-Benz Center or call
Roadside Assistance.
Incorrect wheel bolts or improperly tight-
ened wheel bolts can cause the wheel to
come off. This could cause an accident.
Make sure to use the correct wheel bolts.