2008 MERCEDES-BENZ CLK350 garage door opener

Contents
Power windows .................................. 250
Opening and closing the windows 250
Synchronizing power windows ..... 252
Summer opening feature .............. 253
Convenience closing feature ........ 254
Opening and closing all side
windows with the soft top switch
(CLK cabriolet) ............................. 255
Power tilt/sliding sunroof* (Coupe)... 256
Opening and closing
the power tilt/sliding sunroof ...... 256
Synchronizing
the power tilt/sliding sunroof ...... 258
Soft top (Cabriolet) ............................ 259
Opening and closing the soft top . 259
Opening and closing the soft top
with the SmartKey ........................ 263
Luggage cover .............................. 264
Wind screen ................................. 265
Driving systems ................................. 267
Cruise control............................... 267
Parktronic system
(Parking assist)*,
CLK 63 AMG (USA),
Canada all models ........................ 271Loading .............................................. 275
Roof rack (CLK coupe only) .......... 275
Ski bag* (Canada only) ................ 276
Split rear bench seat
(CLK coupe only) .......................... 281
Loading instructions..................... 283
Cargo tie-down rings
(CLK coupe only) .......................... 284
Useful features .................................. 285
Storage compartments ................ 285
Center armrest ............................. 287
Armrest in the
rear passenger compartment ....... 287
Cup holders.................................. 288
Ashtrays ....................................... 289
Cigarette lighter ........................... 290
Power outlet in the
rear passenger compartment ....... 291
Floormats* ................................... 291
Telephone* .................................. 292
Tele Aid ........................................ 295
Garage door opener* ................... 301
Operation......................................... 307
The first 1 000 miles (1 500 km) ........ 308
Driving instructions ........................... 309
Drive sensibly – save fuel............. 309
Drinking and driving ..................... 309
Pedals .......................................... 309
Power assistance ......................... 310
Brakes.......................................... 310
Driving off .................................... 312
Parking......................................... 312
Tires ............................................. 313
Hydroplaning................................ 314
Tire traction ................................. 314
Tire speed rating .......................... 315
Winter driving instructions ........... 316
Standing water............................. 317
Passenger compartment .............. 317
Driving abroad ............................. 317
Control and operation
of radio transmitters .................... 317
Catalytic converter....................... 318
Emission control .......................... 318
Coolant temperature.................... 319

33 At a glance
Overhead control panel
Overhead control panel
CLK coupe
ItemPage
1Rear interior lighting on/off
(CLK coupe)137
2Power tilt/sliding sunroof*
(CLK coupe)256
3Right reading lamp on/off137
4Interior lighting control136
5Interior rear view mirror47,
185
6Garage door opener*301
7Hands-free microphone for
Tele Aid (emergency call
system) and telephone*292
8Left reading lamp on/off137
9Tele Aid (emergency call
system) button295

301 Controls in detail
Useful features
Stolen Vehicle Recovery services
In the event your vehicle was stolen:
Report the incident to the police.
The police will issue a numbered
incident report.
Pass this number on to the
Mercedes-Benz Response Center along
with your password issued to you when
you subscribed to the service.
The Response Center will then attempt
to covertly contact the vehicle’s
Tele Aid system. Once the vehicle is
located, the Response Center will
contact the local law enforcement and
you. The vehicle’s location will only be
provided to law enforcement.
If you have any questions, please call the
Response Center at 1-800-756-9018 (in
the USA) or 1-888-923-8367 (in Canada).
Garage door opener*
The integrated remote control is capable of
operating up to three separately controlled
devices. It provides a convenient way to re-
place up to three hand-held remote con-
trols used to operate devices such as
garage door openers, gate openers, or oth-
er devices compatible with HomeLink
® or
some other systems.
Before the integrated remote control can
be used, it must be programmed to the ga-
rage door opener, gate operator or other
device you wish to operate. See the follow-
ing instructions for programming
information.
iThe remote door unlock feature is available
if the relevant cellular phone network is avail-
able.
The SOS button will flash and the message
Connecting Call will appear in the multifunc-
tion display to indicate receipt of the door unlock
command.
Once the vehicle is unlocked, a Response Center
specialist will attempt to establish voice contact
with the vehicle occupants.
If the trunk recessed handle was pulled for more
than 20 seconds before door unlock authoriza-
tion was received by the Response Center, you
must wait 15 minutes before pulling the trunk
recessed handle again.
iWhen the anti-theft alarm stays on for more
than 30 seconds, a call is initiated automatically
to the Response Center, see “Anti-theft alarm
system” (
page 97).

302 Controls in detail
Useful features
Interior rear view mirror with integrated re-
mote control
1Indicator lamp
2 3 4Signal transmitter button
Needed for programming (not part of
vehicle equipment):
5Hand-held remote control of ga-
rage door opener, gate operator
or other device
6Hand-held remote control
buttonProgramming the integrated remote
control
Step 1:
Switch on the ignition (page 40).
Step 2:
If you have previously programmed a
signal transmitter button and wish to
retain its programming, proceed to
step 3.
If you are programming the integrated
remote control for the first time, press
and hold the two outer signal transmit-
ter buttons2 and4 and release
them only when indicator lamp1
Warning!G
Before programming the integrated remote
control to a garage door opener or gate
operator, make sure people and objects are
out of the way of the device to prevent po-
tential harm or damage. When programming
a garage door opener, the door moves up or
down. When programming a gate operator,
the gate opens or closes.
Do not use the integrated remote control
with any garage door opener that lacks
safety stop and reverse features as required
by U.S. federal safety standards (this
includes any garage door opener model
manufactured before April 1, 1982).
A garage door that cannot detect an object
– signaling the door to stop and reverse –
does not meet current U.S. federal safety
standards.
When programming a garage door opener,
park outside the garage.
Do not run the engine while programming
the integrated remote control. Inhalation of
exhaust gas is hazardous to your health. All
exhaust gas contains carbon monoxide
(CO), and inhaling it can cause unconscious-
ness and possible death.

303 Controls in detail
Useful features
begins to flash after approximately
20 seconds (do not hold the button for
longer than 30 seconds). This proce-
dure erases any previous settings for
all three channels and initializes the
memory.
If you later wish to program a second
and/or third hand-held transmitter to
the remaining two signal transmitter
buttons, do not repeat this step and be-
gin directly with step 3.
Step 3:
Hold the end of hand-held remote
control5 of the device you wish to
train approximately 2 to 5 inches
(5 to12 cm) away from the signal trans-
mitter button (2, 3 or4) to be pro-
grammed, while keeping indicator
lamp1 in view.
Step 4:
Using both hands, simultaneously
press hand-held remote control
button6 and the desired signal trans-mitter button (2, 3 or4). Do not
release the buttons until step 5 is com-
pleted.
Indicator lamp1 will flash, first slowly
and then rapidly.
Step 5:
After indicator lamp1 changes from a
slow to a rapidly flashing light, release
the hand-held remote control button
and the signal transmitter button.
Step 6:
Press and hold the just-trained signal
transmitter button (2, 3 or4) and
observe indicator lamp1.If indicator lamp1 stays on
constantly, programming is complete
and your device should activate when
the respective signal transmitter
button (2, 3 or4) is pressed and
released.
Step 7:
To program the remaining two signal
transmitter buttons, repeat the steps
above starting with step 3.
iIndicator lamp1 flashes immediately the
first time the signal transmitter button is pro-
grammed. If this button has already been pro-
grammed, the indicator lamp will only start
flashing after 20 seconds.iIf indicator lamp1 flashes rapidly for about
2 seconds and then turns to a constant light,
continue with programming steps 8 through 12
as your garage door opener may be equipped
with the “rolling code” feature.

304 Controls in detail
Useful features
Rolling code programming
To train a garage door opener (or other
rolling code devices) with the rolling code
feature, follow these instructions after
completing the “Programming” portion
(steps 1 through 6) of this text. (A second
person may make the following training
procedures quicker and easier.)
Step 8:
Locate “training” button on the garage
door opener motor head unit.
Exact location and color of the button
may vary by garage door opener brand.
Depending on manufacturer, the
“training” button may also be referred
to as “learn” or “smart” button. If there
is difficulty locating the transmitting
button, refer to the garage door opener
Operator’s Manual.
Step 9:
Press the “training” button on the ga-
rage door opener motor head unit.
The “training light” is activated.You have 30 seconds to initiate the
following step.
Step 10:
Return to the vehicle and firmly press,
hold for 2 seconds and release the pro-
grammed signal transmitter button
(2, 3 or4).
Step 11:
Press, hold for 2 seconds and release
same signal transmitter button a sec-
ond time to complete the training
process.Step 12:
Confirm the garage door operation by
pressing the programmed signal trans-
mitter button (2, 3 or4).
Step 13:
To program the remaining two signal
transmitter buttons, repeat the steps
above starting with step 3.
Gate operator/Canadian programming
Canadian radio-frequency laws require
transmitter signals to “time-out” (or quit)
after several seconds of transmission
which may not be long enough for the
integrated signal transmitter to pick up the
signal during programming. Similar to this
Canadian law, some U.S. gate operators
are designed to “time-out” in the same
manner.
If you live in Canada or if you are having
difficulties programming a gate operator
(regardless of where you live) by using the
programming procedures, replace step 4
with the following:
iSome garage door openers (or other rolling
code equipped devices) may require you to
press, hold for 2 seconds and release the same
signal transmitter button a third time to com-
plete the training process.

306 Controls in detail
Useful features
Programming tips
If you are having difficulty programming
the integrated remote control, here are
some helpful tips:

Check the frequency of hand-held re-
mote control5 (typically located on
the reverse side of the remote). The in-
tegrated remote control is compatible
with radio-frequency devices operating
between 280-390 MHz.

Put a new battery in hand-held remote
control5. This will increase the likeli-
hood of the hand-held remote control
sending a faster and more accurate sig-
nal to the integrated remote control.

While performing step 3, hold
hand-held remote control5 at differ-
ent lengths and angles from the signal
transmitter button (2, 3 or4) you
are programming. Attempt varying an-
gles at the distance of 2 to 5 in
(5 to 12 cm) away or the same angle at
varying distances.

If another hand-held remote control is
available for the same device, try the
programming steps again using that
other hand-held remote control. Make
sure new batteries are in the hand-held
remote control before beginning the
procedure.

Straighten the antenna wire from the
garage door opener assembly. This
may help improve transmitting and/or
receiving signals.
iCertain types of garage door openers are in-
compatible with the integrated remote control. If
you should experience further difficulties with
programming the integrated remote control,
contact an authorized Mercedes-Benz Center, or
call Mercedes-Benz Customer Assistance
Center (in the USA only) at
1-800-FOR-MERCedes, or Customer Service (in
Canada) at 1-800-387-0100.
iUSA only:
This device complies with Part 15 of the
FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interfer-
ence, and
(2) this device must accept any interference
received, including interference that may
cause undesired operation.
Any unauthorized modification to this device
could void the user’s authority to operate the
equipment.
iCanada only:
This device complies with RSS-210 of Industry
Canada. Operation is subject to the following
two conditions:
(1) This device may not cause interference, and
(2) this device must accept any interference
received, including interference that may
cause undesired operation of the device.
Any unauthorized modification to this device
could void the user’s authority to operate the
equipment.

504 Index
G
Garage door opener 33, 301
Gasoline see Fuel
GAWR 358
Gear range
Automatic transmission 177
Limiting 177
Shifting into optimal 180, 182
Gear selector lever 51, 172
Cleaning 375
Gearshift pattern 172
Lock 52
Message in display 400
Position 173, 174
Position indicator 29, 141
Shifting procedure 173
Unlocking in an emergency 429
Gear selector lever one-touch gearshifting
Automatic transmission 179
Global locking/unlocking
see Key, SmartKey or KEYLESS-GO*
Glove box 285
Gloves 422
Good visibility 185
Gross Axle Weight Rating see GAWR
Gross Vehicle Weight Rating see GVWRGross Vehicle Weight see GVW
GVW 358
GVWR 359
H
Halogen headlamp see Headlamps
Hands-free microphone 33
Hard plastic trim items, cleaning 375
Hazard warning flasher 135
Head restraints 43, 120
Active head restraints 81
Front seat 120
Power seat, Adjusting 43
Rear seat 120, 123
Rear seat, Folding back 121
Rear seat, Lowering 123
Rear seat, Placing upright 122
Rear seat, Raising 123
Rear seat, Removing/installing 122
Headlamp
cleaning system* 185, 330, 496
Headlamp delayed shut-off see
Delayed shut-off, Exterior lampsHeadlamps
Automatic headlamp mode 130
Cleaning lenses 372
Daytime running lamp mode 131
Halogen 446
High beam see High beam flasher
High beam see High beam headlamps
Light sensor 411
Locator lighting 132
Low beam headlamps 130
Low beam see Low beam headlamps
Manual headlamp mode 130
Messages in display 411–415
Night security illumination 132
Replacing bulbs 444, 446
Switch 55, 129
Headliner and shelf below rear window,
Cleaning and care of 375
Head-thorax air bag 71
Heated seats* 125
High beam flasher 55, 133
Replacing bulbs (Bi-Xenon*) 444
Replacing bulbs (Halogen) 444