2008 MERCEDES-BENZ CLK350 buttons

299 Controls in detail
Useful features
Information button¡
The Information button¡ is located
below the center armrest cover.
Press and hold the ¡button (for
longer than 2 seconds).
A call to the Customer Assistance
Center will be initiated. The
¡button will flash while the call is
in progress. The message
Connecting Call will appear in the
multifunction display and the audio
system is muted.
When the connection is established, the
message
Call Connected appears in the
multifunction display. The Tele Aid system
will transmit data generating the vehicle
identification number, model, color and
location (subject to availability of cellular
and GPS signals).
A voice connection between the Customer
Assistance Center representative and the
occupants of the vehicle will be
established. Information regarding the
operation of your vehicle, the nearest Mercedes-Benz Center or Mercedes-Benz
USA products and services is available to
you.
For more details concerning the Tele Aid
system, please visit www.mbusa.com and
use your ID and password (sent to you
separately) to learn more (USA only).
iThe indicator lamp on the Information
button¡ remains illuminated in red for ap-
proximately 10 seconds during the system
self-check after switching on the ignition (togeth-
er with the SOS button and the Roadside Assis-
tance button•).
See System self-check (
page 295) when the
indicator lamp does not come on in red or stays
on longer than approximately 10 seconds.If the indicator lamp on the Information
button¡ is flashing continuously and there
was no voice connection to the Response Center
established, then the Tele Aid system could not
initiate an Information call (e.g. the relevant cel-
lular phone network is not available). The mes-
sage
Call Failed appears in the multifunction
display.
Information calls can be terminated using
thetbutton on the multifunction steering
wheel or the respective button for ending a
telephone call on the audio system or the
COMAND* head unit.
!If the indicator lamps do not start flashing
after pressing one of the buttons or remain illu-
minated (in red) at any time, the Tele Aid system
has detected a malfunction or the service is not
currently active, and may not initiate a call. Visit
an Mercedes-Benz Center and have the system
checked or contact the Response Center at
1-800-756-9018 (in the USA) or
1-888-923-8367 (in Canada) as soon as
possible.

302 Controls in detail
Useful features
Interior rear view mirror with integrated re-
mote control
1Indicator lamp
2 3 4Signal transmitter button
Needed for programming (not part of
vehicle equipment):
5Hand-held remote control of ga-
rage door opener, gate operator
or other device
6Hand-held remote control
buttonProgramming the integrated remote
control
Step 1:
Switch on the ignition (page 40).
Step 2:
If you have previously programmed a
signal transmitter button and wish to
retain its programming, proceed to
step 3.
If you are programming the integrated
remote control for the first time, press
and hold the two outer signal transmit-
ter buttons2 and4 and release
them only when indicator lamp1
Warning!G
Before programming the integrated remote
control to a garage door opener or gate
operator, make sure people and objects are
out of the way of the device to prevent po-
tential harm or damage. When programming
a garage door opener, the door moves up or
down. When programming a gate operator,
the gate opens or closes.
Do not use the integrated remote control
with any garage door opener that lacks
safety stop and reverse features as required
by U.S. federal safety standards (this
includes any garage door opener model
manufactured before April 1, 1982).
A garage door that cannot detect an object
– signaling the door to stop and reverse –
does not meet current U.S. federal safety
standards.
When programming a garage door opener,
park outside the garage.
Do not run the engine while programming
the integrated remote control. Inhalation of
exhaust gas is hazardous to your health. All
exhaust gas contains carbon monoxide
(CO), and inhaling it can cause unconscious-
ness and possible death.

303 Controls in detail
Useful features
begins to flash after approximately
20 seconds (do not hold the button for
longer than 30 seconds). This proce-
dure erases any previous settings for
all three channels and initializes the
memory.
If you later wish to program a second
and/or third hand-held transmitter to
the remaining two signal transmitter
buttons, do not repeat this step and be-
gin directly with step 3.
Step 3:
Hold the end of hand-held remote
control5 of the device you wish to
train approximately 2 to 5 inches
(5 to12 cm) away from the signal trans-
mitter button (2, 3 or4) to be pro-
grammed, while keeping indicator
lamp1 in view.
Step 4:
Using both hands, simultaneously
press hand-held remote control
button6 and the desired signal trans-mitter button (2, 3 or4). Do not
release the buttons until step 5 is com-
pleted.
Indicator lamp1 will flash, first slowly
and then rapidly.
Step 5:
After indicator lamp1 changes from a
slow to a rapidly flashing light, release
the hand-held remote control button
and the signal transmitter button.
Step 6:
Press and hold the just-trained signal
transmitter button (2, 3 or4) and
observe indicator lamp1.If indicator lamp1 stays on
constantly, programming is complete
and your device should activate when
the respective signal transmitter
button (2, 3 or4) is pressed and
released.
Step 7:
To program the remaining two signal
transmitter buttons, repeat the steps
above starting with step 3.
iIndicator lamp1 flashes immediately the
first time the signal transmitter button is pro-
grammed. If this button has already been pro-
grammed, the indicator lamp will only start
flashing after 20 seconds.iIf indicator lamp1 flashes rapidly for about
2 seconds and then turns to a constant light,
continue with programming steps 8 through 12
as your garage door opener may be equipped
with the “rolling code” feature.

304 Controls in detail
Useful features
Rolling code programming
To train a garage door opener (or other
rolling code devices) with the rolling code
feature, follow these instructions after
completing the “Programming” portion
(steps 1 through 6) of this text. (A second
person may make the following training
procedures quicker and easier.)
Step 8:
Locate “training” button on the garage
door opener motor head unit.
Exact location and color of the button
may vary by garage door opener brand.
Depending on manufacturer, the
“training” button may also be referred
to as “learn” or “smart” button. If there
is difficulty locating the transmitting
button, refer to the garage door opener
Operator’s Manual.
Step 9:
Press the “training” button on the ga-
rage door opener motor head unit.
The “training light” is activated.You have 30 seconds to initiate the
following step.
Step 10:
Return to the vehicle and firmly press,
hold for 2 seconds and release the pro-
grammed signal transmitter button
(2, 3 or4).
Step 11:
Press, hold for 2 seconds and release
same signal transmitter button a sec-
ond time to complete the training
process.Step 12:
Confirm the garage door operation by
pressing the programmed signal trans-
mitter button (2, 3 or4).
Step 13:
To program the remaining two signal
transmitter buttons, repeat the steps
above starting with step 3.
Gate operator/Canadian programming
Canadian radio-frequency laws require
transmitter signals to “time-out” (or quit)
after several seconds of transmission
which may not be long enough for the
integrated signal transmitter to pick up the
signal during programming. Similar to this
Canadian law, some U.S. gate operators
are designed to “time-out” in the same
manner.
If you live in Canada or if you are having
difficulties programming a gate operator
(regardless of where you live) by using the
programming procedures, replace step 4
with the following:
iSome garage door openers (or other rolling
code equipped devices) may require you to
press, hold for 2 seconds and release the same
signal transmitter button a third time to com-
plete the training process.

305 Controls in detail
Useful features
Step 4:
Press and hold the signal transmitter
button (2, 3 or4). Do not release
this button until it has been successful-
ly trained.
While still holding down the signal
transmitter button (2, 3 or4),
“cycle” your hand-held remote control
button6 as follows: Press and hold
button6 for 2 seconds, then release
it for 2 seconds, and again press and
hold it for 2 seconds. Repeat this se-
quence on the hand-held remote con-
trol until the frequency signal has been
learned. Upon successful training, indi-
cator lamp1 will flash slowly and then
rapidly after several seconds.
Proceed with programming step 5 and
step 6 to complete.Reprogramming a single signal trans-
mitter button
To program a device using a signal trans-
mitter button previously trained, follow
these steps:
Switch on the ignition (page 40).
Press and hold the desired signal
transmitter button (2, 3 or4).
Do not release the button.
Indicator lamp1 will begin to flash af-
ter 20 seconds. Without releasing the
signal transmitter button, proceed with
programming starting with step 3.Operation of integrated remote control
Switch on the ignition (page 40).
Select and press the appropriate
integrated signal transmitter button
(2, 3 or4) to activate the remote
controlled device.
The integrated remote control trans-
mitter continues to send the signal as
long as the button is pressed – up to
20 seconds.
Erasing the integrated remote control
memory
Switch on the ignition (page 40).
Simultaneously press and hold outer
signal transmitter buttons2 and 4,
for approximately 20 seconds, until
indicator lamp1 flashes rapidly. Do
not hold for longer than 30 seconds.
The codes of all three channels are
erased.
iUpon completion of programming the inte-
grated remote control, make sure you retain the
hand-held remote control that came with the ga-
rage door opener, gate operator or other device.
You may need it for use in other vehicles, for fu-
ture programming of an integrated remote con-
trol, or simply for continued use as a hand-held
remote control to operate the respective device
in other situations.
iIf you sell your vehicle, erase the codes of all
three channels.

507 Index
Instrument cluster 378–387, 388
Low beam headlamp 29
Parktronic system* warning
indicators (Canada only) 273
Roll bar 385
Seat belt telltale 29
SRS 29, 65, 387
Turn signals 29
Language, Setting 158
LATCH-type child seat anchors see
Children in the vehicle
License plate lamps
Messages in display 413
Replacing bulbs 444, 449
Light alloy wheels, cleaning 374
Light sensor
Messages in display 411
Lighter see Cigarette lighter
Lighting, Exterior and interior 129
Limp-home mode 184
Load limit 360
Loading
Ski bag* (Canada only) 278
Loading see Vehicle loading
Loading the vehicle 334
Locator lighting 132, 163Lock buttons
Door handle (KEYLESS-GO*) 62, 107
Loss of keys 109
Loss of Service and
Warranty Information Booklet 477
Low beam headlamps
Indicator lamp 29
Messages in display 413
Replacing bulbs (Bi-Xenon*) 444
Replacing bulbs (Halogen) 444, 446
Switching on 55
Lubricants 489
Luggage cover 264
Folding back 276M
Maintenance 12, 364
Calling up service indicator 366
Clearing service indicator 365
Maintenance System
(U.S. vehicles) 364
Resetting service indicator 366
Service indicator 364
Service term exceeded 365
Manual headlamp mode see Headlamps
Manual shift program
Deactivating 184
Manual shift program CLK 63 AMG 182
MAXCOOL maximum cooling 207
Maximum load rating, Tires 359
Maximum loaded vehicle weight,
Tire inflation pressure 359
Maximum tire inflation pressure 359
Mechanical key 427
Memory function see Seats, Power
Menus see Control system menus
Microphone, Hands-free 33
Minispare wheel see Spare wheel

513 Index
Ski bag* (Canada only) 276
Loading 278
Luggage cover 276
Removing 280
Ski bag roller blind 276, 280
Unfolding (Cabriolet) 276
Unfolding (Coupe) 277
Unloading and folding 279
Ski bag* roller blind 276
SmartKey see Key, SmartKey
SmartKey with KEYLESS-GO*
see KEYLESS-GO*
Snow chains 363
Snow tires 362
Soft top 259
Cleaning 370
Emergency operations 432–439
Locking after raising/lowering 262
Luggage cover 264
Messages in display 420
Opening/closing 259
Opening/closing, SmartKey 263
Opening/closing,
Soft top switch 260, 261
Wind screen 265
Soft top switch 255, 260Sound system* 213, 217
Spare parts service see Parts service
Spare wheel 425
Bolts 422, 426
Mounting 458
Sizes 486
Speedometer 29, 158
SRS 64, 78
Indicator lamp 29, 65, 387
Message in display 416
Standard display, Selecting display 159
Standing lamps 447, 448
Replacing bulbs 444
Standing water, Driving through 317
Starter switch 27, 38
Positions 38
Starting difficulties, Engine 53
Starting, Engine 51
Status line, Selecting display 159
Steering column 44, 45
Steering gear oil
Message in display 417
Steering wheel 44, 45
Buttons 30
Cleaning 375
Lock 53Steering wheel gearshift control
one-touch gearshifting*
Automatic transmission 180
Stolen Vehicle Recovery services 301
Storage box 285
Storage compartments 285
Armrest, Front 287
Armrest, Rear 287
Cup holder 288
Glove box 285
Parcel net 286
Storage bags 286
Storage box 285
Storing
Tires 333
Sun visors 187
Sunroof* see Power tilt/sliding sunroof*
Sunshade* (Canada only) 188
Supplemental Restraint System see SRS
Symbols used
in this operator’s manual 15