2008 MERCEDES-BENZ C300 Esp reset

37 Safety and Security
Occupant safety

Always sit as upright as possible, prop-
erly use the seat belts and use an appro-
priately sized infant restraint, toddler
restraint, or booster seat recommended
for the size and weight of the child.
Failure to follow these instructions can
result in severe injuries to you or other
occupants.
If you sell your vehicle, it is important that
you make the buyer aware of this safety
information. Be sure to give the buyer this
Operator’s Manual.
Warning!G
Accident research shows that the safest
place for children in an automobile is in the
rear seat.
There is a possibility for a side impact air
bag related injury if occupants, especially
children, are not properly seated or re-
strained when next to a front side impact air
bag and/or rear side impact air bag* which
needs to deploy rapidly in a side impact in
order to do its job.
To help avoid the possibility of injury, please
follow these guidelines:
(1) Always sit as upright as possible,
properly use the seat belts, and for all
children 12 years old and under, use an
appropriately sized infant restraint, tod-
dler restraint, or booster seat recom-
mended for the size and weight of the
child.
(2) Always wear seat belts properly.iAir bags are designed to deploy only in cer-
tain frontal impacts (front air bags), and in side
impacts (front side impact air bags, rear side im-
pact* air bags, and window curtain air bags)
which exceed preset thresholds, and in certain
rollovers (window curtain air bags). Only during
these events will they provide their supplemental
protection.
The driver and passengers should always wear
their seat belts. Otherwise it is not possible for
air bags to provide their supplemental protec-
tion.
In case of other types of impacts and impacts be-
low air bag deployment thresholds, air bags will
not deploy. The driver and passenger will then be
protected to the extent possible by a properly
fastened seat belt. A properly fastened seat belt
is also needed to provide the best possible pro-
tection in a rollover.
We caution you not to rely on the presence of the
air bags in order to avoid wearing your seat belt.
It is important to your safety and that of your pas-
sengers that you replace deployed air bags and
repair any malfunctioning air bags to make sure
the vehicle will continue to provide supplemental
crash protection for occupants.

99 Controls in detail
Mirrors
Folding exterior rear view mirrors in
and out automatically
When the corresponding function in the
control system is activated (
page 175):

The exterior rear view mirrors automat-
ically fold in as soon as the vehicle is
locked from the outside.

The exterior rear view mirrors automat-
ically fold out as soon as the vehicle is
unlocked and the driver’s or front pas-
senger door are subsequently opened.Resetting the automatic exterior rear
view mirror fold in function
You need to reset the automatic exterior
rear view mirror fold in function whenever
the battery was disconnected or dis-
charged.
Switch on the ignition.
Briefly press button1.Interior rear view mirror, antiglare
position
1Lever
Tilt the mirror to the antiglare position
by moving lever 1 towards the wind-
shield.
The interior rear view mirror is dimmed.
iThe mirrors do not fold out automatically if
they were previously folded in manually with
button1.
iIf you are driving at more than approximately
9 mph (15 km/h), you will not be able to fold the
exterior mirrors in.
iYou need to manually fold in the mirrors
once, so that the automatic fold in function will
work, see “Setting fold-in function* for exterior
rear view mirrors” (
page 175).

113 Controls in detail
Lighting
Switching on corner-illuminating front
fog lamps
Switch on the left or right turn signal
(
page 108), depending on whether
you are turning left or right.
The respective corner-illuminating
front fog lamp comes on and illumi-
nates the area in the direction into
which you are turning.
or
Turn steering wheel in desired
direction.
The corner-illuminating front fog lamp
on the side of your steering direction
comes on.Switching off the corner-illuminating
lamps
The combination switch for the turn signal
resets automatically after major steering
wheel movements. This will switch off the
corner-illuminating lamps if they were acti-
vated by switching on the left or right turn
signal.
If the turn signal should stay on after mak-
ing the turn, the turn signal and corner-illu-
minating lamp can be switched off by
returning the combination switch to its
original position.
iIf you have switched on the turn signal for
one side but turn the steering wheel in the
opposite direction, the corner-illuminating front
fog lamp comes on for the side indicated by the
turn signal.
The corner-illuminating front fog lamp remains lit
for a maximum of 3 minutes. Afterward, it goes
out even if the turn signal is still switched on.
iThe corner-illuminating lamps temporarily
come on both sides of the vehicle if you turn the
steering wheel in one direction and then in the
other direction shortly thereafter.
iThe corner-illuminating lamps will come on
automatically depending on the steering angle,
even if you did not switch on either turn signal. If
the corner-illuminating lamps came on automat-
ically, they will also go out automatically depend-
ing on the steering angle.
iWhen you shift the transmission in reverse
gear, the corner-illuminating lamp opposite to
your steering direction comes on.
The turn signal has no influence on the
corner-illuminating lamp on the outside of the
curve.
iThe corner-illuminating lamp may remain lit
for a short time. The corner-illuminating lamp
comes on for no more than 20 seconds with the
vehicle standing still. It is then switched off even
if the turn signal is still switched on or you have
turned the steering wheel to full lock.

131 Controls in detail
Driving and parking
Automatic transmission*
Depress the brake pedal.
The gear selector lever can now be
used.
Release the parking brake by pulling on
release handle1.
The indicator lamp; (USA only)
or3 (Canada only) in the instru-
ment cluster goes out.
Shift automatic transmission toD orR.
Release the brake pedal.
Carefully depress the accelerator
pedal.
After a cold start, the automatic transmis-
sion shifts at a higher engine revolution.
This allows the catalytic converter to reach
its operating temperature earlier.
For more information, see “Driving instruc-
tions” (
page 311).
Turn signals
Combination switch
1Turn signals, right
2Turn signals, left
Press the combination switch in the
direction of arrow1 or2.
The corresponding turn signal indicator
lampL orK in the instrument
cluster flashes (
page 26).
The combination switch resets automati-
cally after major steering wheel move-
ments.
Warning!G
It is dangerous to shift the gear selector le-
ver out of P or N if the engine speed is high-
er than idle speed. If your foot is not firmly
on the brake pedal, the vehicle could accel-
erate quickly forward or in reverse. You
could lose control of the vehicle and hit
someone or something. Only shift into gear
when the engine is idling normally and when
your right foot is firmly on the brake pedal.
iShifting from gear positionP to positionR,
N, or D is only possible with the brake pedal de-
pressed. Without the brake pedal depressed, the
gear selector lever can be moved, but the park-
ing pawl remains engaged, not allowing shifting
to occur.
iWait for the gear selection process to com-
plete before setting the vehicle in motion.
!Shift the automatic transmission toP orR
only when the vehicle is stopped in order to avoid
damaging the transmission.

172 Controls in detail
Control system
Depending on the previous status, the
daytime running lamps feature will be
Enabled orDisabled.
With
Daytime Running Lamps mode En-
abled
selected and the exterior lamp
switch at position M or *, the low
beam headlamps are switched on when
the engine is running.
In low ambient light conditions the follow-
ing lamps will switch on additionally:

Parking lamps

Tail lamps

License plate lamps

Side marker lamps
also illuminates the instrument cluster.
For more information on the daytime run-
ning lamp mode (
page 110).Setting locator lighting
Press % or $ to select the
Lights submenu.
Press #.
Press % or $ to select the Sur-
round Lighting
feature.
Press #.
The current setting
Enabled
or
Disabled is shown.
Press # again if you would like to
change the current status.
Depending on the previous status, the
locator lighting feature will be
Enabled
or
Disabled.
With the locator lighting feature activated
and the exterior lamp switch in
positionU, the following lamps will
switch on during darkness when the vehi-
cle is unlocked with the SmartKey:

Parking lamps

Tail lamps

License plate lamps

Side marker lamps

Front fog lamps
also illuminates the instrument cluster.
iIf you turn the exterior lamp switch to anoth-
er position, the corresponding lamp(s) will
switch on.
iMake sure the light switch is set toB
or* when you switch off the daytime running
lamps while driving at night.
iFor safety reasons, resetting the Lights
submenu to factory settings (
page 165) while
driving will not deactivate the daytime running
lamp mode.
The following message appears in the
multifunction display:
Lighting - Cannot be completely reset
to factory settings while driving.


198 Controls in detail
Audio system
Tuning to a station by entering the fre-
quency manually
b
Radio
Enter Frequency
The menu for manual frequency entry
appears.
or
Press buttonó, on the keypad in
audio control unit briefly.
Enter frequency with keypad:
Enter desired frequency with
buttons1to R, with the keypad
in audio control unit briefly.
The audio system tunes in to the fre-
quency entered.
Exiting menu without making an en-
try: Press button í in the center
console (
page 184).Storing stations
You can store ten AM and ten FM stations
in the memory.
Storing stations manually with keypad
Tune in desired station.
Basic menu is shown in the audio
display.
Press and hold desired station
button1 to R until a brief signal
tone sounds.
The station is stored.
iThis function is not available for Weather
Band.
iIt is not possible to enter a frequency in the
respective waveband which is outside the fre-
quency range.
iIf you select a memory preset which is al-
ready in use, it will be overwritten by the new
station.

199 Controls in detail
Audio system
Storing stations manually with station
memory menu
Tune in desired station.
Basic menu is shown in the audio
display.
Press n when the main area is active.
or
Select Presets.
The station memory display appears in the
audio display.
The dot R in front of a memory position
indicates that the currently tuned station is
stored there.
Selecting a memory position:
Slideqmr or rotate ymz.
Storing a station to a selected mem-
ory position: Press and hold n until a
brief signal tone sounds.
or
Press and hold desired station
button1 to R on keypad, until a
brief signal tone sounds.
The station is stored.
Autostore – automatic station memory
Press b button on audio control
unit repeatedly until desired waveband
has been selected.Basic menu is shown in the audio
display.
Press n when the main area is active.
or
Select Presets.
The station memory display appears in the
audio display.
Slideqmr or rotate ymz to select Au-
tostore
.
Press n.
The audio system searches for receivable
stations. A corresponding message is dis-
played. The available stations are automat-
ically stored in memory. The first received
station will be automatically played.
Canceling storage procedure:
Pressn while the “Searching” mes-
sage is being displayed.
iThis function is not available for Weather
Band. The autostore function automatically as-
signs receivable stations to the memory, sorted
according to reception quality at the moment of
performing the autostore. The stations which
were stored in the station memory manually are
completely lost in this process. If less than ten
stations are found, the remaining entries are left
empty.

205 Controls in detail
Audio system
Channel number is valid, but channel is
not included in subscription: The mes-
sage
Please call SIRIUS to subscribe
pops up (
page 202).
Press n to close the message in the
audio display.
Tuning in channels using the satellite ra-
dio channel list
b
Sat
Channel List.
The channel list appears. The dotR in
front of a list entry indicates the cur-
rently selected channel.
Select channel by rotating ymz or
slidingqmr.
Press n to confirm.Tuning in channels using satellite radio
channel presets
b
Presets.
or
Press n when the main area is select-
ed.
The preset menu appears. The dotR
in front of a preset position indicates
that this is the channel currently select-
ed and being listened to.
Select station in memory by rotating
ymz or sliding qmr.
Press n to confirm.
or
Press desired station button1 to
R, with the keypad in audio control
unit briefly.
The audio system tunes in the correspond-
ing channel as long as it is included in your
subscription and is still available.
If the channel is not included in your sub-
scription, you will see the message de-
scribed in the section “Satellite radio
service is not activated” (
page 202).
If the channel is no longer available, you
will see the message
Invalid Channel.
Closing message: Press n.iThe contents of the channel list depends on
which channels are included in your subscription
and which program category you have selected
(
page 203). If only the preview channel is acti-
vated, the channel list contains only the preview
channel.