2008 MERCEDES-BENZ C300 Controls in detail

106 Controls in detail
Fastening the seat belts
1Seat belt outlet
2Latch plate
3Release button
4Buckle
Pull the seat belt smoothly from the
seat belt outlet1.
Place the shoulder portion of the seat
belt across the top of your shoulder
and the lap portion across your hips.
Push latch plate2 into buckle4 until
it clicks.
If necessary, adjust the seat belt to the
correct height (
page 107).
If necessary, tighten the lap portion to
a snug fit by pulling shoulder portion
up.
To release the seat belt, press release
button3 and guide latch plate2
back to seat belt outlet1.
Proper use of seat belts

Do not twist the seat belt when fasten-
ing.

Adjust seat belt so that the shoulder
portion is located as close as possible
to the middle of the shoulder (it should
not touch the neck). Never pass the
shoulder portion of the seat belt under
your arm.

Position the lap belt as low as possible
on your hips (over hip joint) and not
across the abdomen.

Place the seat backrest in a nearly up-
right position.

Never use a seat belt for more than one
person at a time.

Do not fasten a seat belt around a per-
son and another object at the same
time. When using a seat belt to secure
infant restraints or toddler restraints or
children in booster seats, always follow
the child seat manufacturer’s instruc-
tions.
Warning!G
Read and observe the additional warning no-
tices printed in the “Safety and Security”
section.

107 Controls in detail
Fastening the seat belts

Check your seat belt during travel to
make sure it is properly positioned.

Make sure the seat belt is always fitted
snugly. Take special care of this when
wearing loose clothing.For more information, see “Seat belts”
(
page 46).
Seat belt height adjustment
You can adjust the height of the seat belt
for the driver’s and front passenger seat.
1Release button
Raising: Slide the seat belt height ad-
juster upward.
The seat belt height adjuster engages
in different positions.
Lowering: Press and hold release
button1.
Slide the seat belt height adjuster
downward.
Release button1 and make sure the
seat belt height adjuster engages into
place.
Warning!G
Do not pass seat belts over sharp edges.
They could tear.
Do not allow the seat belt to get caught in
the door or in the seat adjustment mecha-
nism. This could damage the seat belt.
Never attempt to make modifications to
seat belts. This could impair the effective-
ness of the seat belts.
Do not bleach or dye seat belts as this may
severely weaken them. In a crash, they may
not be able to provide adequate protection.
Damaged seat belts or seat belts that were
highly stressed in an accident must be re-
placed. Contact an authorized
Mercedes-Benz Center.

108 Controls in detail
Lighting
Exterior lamp switch
Low beam headlamps
The low beam headlamps can be switched
on and off with the exterior lamp switch us-
ing the manual headlamp mode.
Switching on: Turn the exterior lamp
switch to positionB.
The green indicator lampC in the
exterior lamp switch comes on.
iIf you drive in countries where vehicles drive
on the other side of the road than the country in
which the vehicle is registered, you must have
the headlamps modified for symmetrical low
beams. Relevant information can be obtained at
your authorized Mercedes-Benz Center.1‚Standing lamps, left (turn left two
stops)
2ˆStanding lamps, right (turn left
one stop)
3MOff
Daytime running lamp mode
(
page 110)
4*Automatic headlamp mode
Daytime running lamp mode
(
page 110)
5CParking lamps (also side marker
lamps, tail lamps, license plate
lamps, instrument panel lamps)
6BLow beam headlamps or high
beam headlamps
7‡Front fog lamps
8†Rear fog lamp
iIf you hear a warning signal you have
forgotten to switch off the low beam headlamps
or the parking lamps before opening the driver’s
door.
In addition the message
Switch Off Lights
appears in the multifunction display.
Switch off the low beam headlamps or the park-
ing lamps.
If the message
Switch Off Lights or Re-
move Key
appears in the multifunction display
remove the SmartKey from the starter switch or
switch off the automatic headlamp mode.
!Failure to switch off the exterior lamps when
leaving the vehicle may result in a discharged
battery.

109 Controls in detail
Lighting
The following lamps switch on:

Low beam headlamps

Tail and parking lamps

License plate lamps

Side marker lamps
Switching off: Turn the exterior lamp
switch to positionM.
The green indicator lampC in the
exterior lamp switch goes out.
Automatic headlamp mode
The following lamps switch on and off au-
tomatically depending on the brightness of
the ambient light:

Low beam headlamps

Tail and parking lamps

License plate lamps

Side marker lamps
Turn the exterior lamp switch to
position*.
With the SmartKey in starter switch
position1 or the KEYLESS-GO*
start/stop button (Canada only)
pressed once, the tail and parking
lamps, the license plate lamps and the
side marker lamps will switch on and
off depending on the brightness of the
ambient light.
When the engine is running, the low
beam headlamps, the tail and parking
lamps, the license plate lamps, and the
side marker lamps will switch on and
off depending on the brightness of the
ambient light.
Warning!G
If the exterior lamp switch is set to*,
the headlamps will not be automatically
switched on under foggy conditions.
To minimize risk to you and to others,
activate headlamps by turning exterior lamp
switch to positionB when driving or
when traffic and/or ambient lighting condi-
tions require you to do so.
In low ambient lighting conditions, only
switch from position * to B with the
vehicle at a standstill in a safe location.
Switching from position* to B will
briefly switch off the headlamps. Doing so
while driving in low ambient lighting condi-
tions may result in an accident.
The automatic headlamp feature is only an
aid to the driver. The driver is responsible for
the operation of the vehicle’s lights at all
times.
iCanada only:
High beam headlamps are only available with the
exterior lamp switch in position B.

110 Controls in detail
Lighting
Daytime running lamp mode
In Canada the daytime running lamp mode
is mandatory and therefore in a constant
mode.
In the USA the daytime running lamp mode
is deactivated by default. Activate the day-
time running lamp mode using the control
system, see “Setting daytime running lamp
mode (USA only)” (
page 171).
Turn exterior lamp switch to
positionM or*.
When the engine is running, the low
beam headlamps are switched on.
In low ambient light conditions, the fol-
lowing lamps will switch on additional-
ly:

Tail and parking lamps

License plate lamps

Side marker lampsCanada only
Vehicles with automatic transmission*:
When the engine is running and you shift
from a driving position to positionN orP,
with the vehicle at a standstill the low
beam headlamps will switch off with a de-
lay of 3-minutes.
When the engine is running, and you

turn the exterior lamp switch to
positionC, the low beam head-
lamps, the tail and parking lamps, the
license plate lamp and the side marker
lamps switch on.

turn the exterior lamp switch to
positionB, the manual headlamp
mode has priority over the daytime run-
ning lamp mode.The corresponding exterior lamps
switch on (
page 108).
USA only
When the engine is running, and you turn
the exterior lamp switch to position C
orB, the manual headlamp mode has
priority over the daytime running lamp
mode.
The corresponding exterior lamps switch
on (
page 108).
iWith the daytime running lamp mode activat-
ed and the engine running, the low beam head-
lamps cannot be switched off manually.
iWith the exterior lamp switch in
positionM or *, you cannot switch on the
high beam headlamps.
The high beam flasher is available at all times.
For nighttime driving you should turn the exterior
lamp switch to positionB to permit activa-
tion of the high beam headlamps.
iWith the daytime running lamp mode
activated and the exterior lamp switch in
position M, you cannot switch on the high
beam headlamps.
The high beam flasher is available at all times.
For nighttime driving you should turn the exterior
lamp switch to positionB or * to permit
activation of the high beam headlamps.

111 Controls in detail
Lighting
Locator lighting and interior lighting
delayed shut-off
The locator lighting and night security illu-
mination are described in the “Control sys-
tem” section, see “Setting locator lighting”
(
page 172) and “Setting interior lighting
delayed shut off” (
page 173).
Fog lampsFront fog lampsTurn the exterior lamp switch to
positionC orB (
page 108).
Pull out exterior lamp switch to first
stop.
The front fog lamps are switched on.
The green indicator lamp‡ in the
exterior lamp switch comes on
(
page 108).
Push in the exterior lamp switch.
The front fog lamps are switched off.
The green indicator lamp‡ in the
exterior lamp switch goes out.Rear fog lamp (driver’s side only)
Turn the exterior lamp switch to
positionB (
page 108).
Pull out exterior lamp switch to second
stop.
The front fog lamps and the rear fog
lamp switch on.
The yellow indicator lamp† in the
exterior lamp switch comes on
(
page 108).
Push in the exterior lamp switch to first
stop.
The rear fog lamp switches off.
The yellow indicator lamp† in the
exterior lamp switch goes out.
The front fog lamps remain lit.
Warning!G
In low ambient lighting or foggy conditions,
only switch from position * to B with
the vehicle at a standstill in a safe location.
Switching from position* to B will
briefly switch off the headlamps. Doing so
while driving in low ambient lighting condi-
tions may result in an accident.
iFog lamps will operate with the parking
lamps and/or the low beam headlamps on. Fog
lamps should only be used in conjunction with
low beam headlamps. Consult your State or
Province Motor Vehicle Regulations regarding
permissible lamp operation.
iFog lamps cannot be switched on manually
with exterior lamp switch in position*. To
activate the fog lamps, turn exterior lamp switch
to positionB first.

112 Controls in detail
Lighting
Switching on high beams
Combination switch
1High beam
2High beam flasher
High beam: Turn the exterior lamp
switch to positionB (
page 108).
Push the combination switch in the di-
rection of arrow1.
The high beam indicatorA in the in-
strument cluster comes on
(
page 26).
High beam flasher: Pull the combina-
tion switch briefly in the direction of
arrow2.
Headlamp cleaning system*
The headlamps are automatically cleaned
with a high-pressure water jet when, at the
same time,

the engine is running

the headlamps are switched on

the windshield wipers have wiped the
windshield with washer fluid for the
first time.
The headlamps are cleaned every tenth
time the windshield is washed with washer
fluid.
When you switch off the headlamps or the
ignition, the automatic function is reset
and will start counting the next time from
the beginning.
For information on filling up the washer
reservoir, see “Windshield washer system
and headlamp cleaning system*”
(
page 330).Corner-illuminating front fog lamps*
(With Bi-Xenon* headlamps only)
The corner-illuminating front fog lamps
improve illumination of the area in the
direction into which you are turning.
The corner-illuminating front fog lamps will
operate with the engine running and with:

the exterior lamp switch in
positionB or* (
page 108)
or

the daytime running lamp mode acti-
vated (
page 110).
iThe corner-illuminating front fog lamps will
only come on in low ambient lighting conditions.
iIf you are driving faster than 25 mph
(40 km/h) or have the front fog lamps switched
on, the corner-illuminating front fog lamps
function is not available.

113 Controls in detail
Lighting
Switching on corner-illuminating front
fog lamps
Switch on the left or right turn signal
(
page 108), depending on whether
you are turning left or right.
The respective corner-illuminating
front fog lamp comes on and illumi-
nates the area in the direction into
which you are turning.
or
Turn steering wheel in desired
direction.
The corner-illuminating front fog lamp
on the side of your steering direction
comes on.Switching off the corner-illuminating
lamps
The combination switch for the turn signal
resets automatically after major steering
wheel movements. This will switch off the
corner-illuminating lamps if they were acti-
vated by switching on the left or right turn
signal.
If the turn signal should stay on after mak-
ing the turn, the turn signal and corner-illu-
minating lamp can be switched off by
returning the combination switch to its
original position.
iIf you have switched on the turn signal for
one side but turn the steering wheel in the
opposite direction, the corner-illuminating front
fog lamp comes on for the side indicated by the
turn signal.
The corner-illuminating front fog lamp remains lit
for a maximum of 3 minutes. Afterward, it goes
out even if the turn signal is still switched on.
iThe corner-illuminating lamps temporarily
come on both sides of the vehicle if you turn the
steering wheel in one direction and then in the
other direction shortly thereafter.
iThe corner-illuminating lamps will come on
automatically depending on the steering angle,
even if you did not switch on either turn signal. If
the corner-illuminating lamps came on automat-
ically, they will also go out automatically depend-
ing on the steering angle.
iWhen you shift the transmission in reverse
gear, the corner-illuminating lamp opposite to
your steering direction comes on.
The turn signal has no influence on the
corner-illuminating lamp on the outside of the
curve.
iThe corner-illuminating lamp may remain lit
for a short time. The corner-illuminating lamp
comes on for no more than 20 seconds with the
vehicle standing still. It is then switched off even
if the turn signal is still switched on or you have
turned the steering wheel to full lock.