2008 MERCEDES-BENZ C300 4MATIC run flat

343 Operation
Tires and wheels
Restart the Run Flat Indicator
The tire inflation pressure monitor must be
restarted in the following situations:

If you have changed the tire inflation
pressure

If you have replaced the wheels or tires

If you have installed new wheels or
tires
Using the Tire and Loading Information
placard on the driver’s door B-pillar
(
page 334) or, if available, the
supplemental tire inflation pressure
information on the inside of the fuel
filler flap (
page 322), make sure the
tire inflation pressure of all four tires is
correct.
Switch on the ignition (page 82).
Press button( or& on the
multifunction steering wheel to select
the menu
Service(page 164).
Press button $or% to select
Run Flat Indicator.
Press the button# to confirm. The
following message appears in the mul-
tifunction display:
Run Flat Indicator
Active
Menu: OK-Button
Press button#.
The following message will appear in
the multifunction display:
Restart
Run Flat Indicator?
Yes
or No
Press button $or% to select
Yes.
Press button# to confirm.
The following message will appear in
the multifunction display:
Run Flat Indicator
Restarted
After a certain “learning phase”, the
Run Flat Indicator checks the set pres-
sure values for all four tires.
Warning!G
The Run Flat Indicator can only warn you in
a reliable manner if you have set the correct
tire inflation pressures for each tire.
If an incorrect tire inflation pressure was
set, the system will monitor the pressure
according to the incorrect value.


344 Operation
Tires and wheels
If you wish to cancel activation:
Press button $or% to select
No.
Press button# to confirm.
The previous settings will not be
changed
or
Wait until the message
Run Flat Indicator?
Restart
disappears.
Checking tire pressure electronically
with the Tire Pressure Monitoring
System (TPMS), (USA only)The TPMS only functions on wheels that
are equipped with the proper electronic
sensors. It monitors the tire inflation pres-
sure, as selected by the driver, in all four
tires. A warning is issued to alert you to a
decrease in pressure in one or more of the
tires.
iThe Tire Pressure Monitoring System
(TPMS) is equipped with a combination low tire
pressure/TPMS malfunction telltale in the
instrument cluster (
page 26). Depending on
how the telltale illuminates, it indicates a low tire
pressure condition or a malfunction in the TPMS
system itself:

If the telltale illuminates continuously, one
or more of your tires is significantly underin-
flated. There is no malfunction in the TPMS.

If the telltale flashes for 60 seconds and
then stays illuminated, the TPMS system
itself is not operating properly.
iThis device complies with Part 15 of the
FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interfer-
ence, and
(2) this device must accept any interference
received, including interference that may
cause undesired operation.
Any unauthorized modification to this device
could void the user’s authority to operate the
equipment.
Warning!G
The TPMS does not indicate a warning for
wrongly selected inflation pressures. Always
adjust tire inflation pressure according to
the Tire and Loading Information placard on
the driver’s door B-pillar or, if available, the
supplemental tire pressure information on
the inside of the fuel filler flap.
The TPMS is not able to issue a warning due
to a sudden dramatic loss of pressure (e.g.
tire blowout caused by a foreign object). In
this case bring the vehicle to a halt by care-
fully applying the brakes and avoiding
abrupt steering maneuvers.


390 Practical hints
What to do if …?
Display Possible cause/consequencePossible solution
Cruise control
- - - mph
(USA only)
You have tried to switch on cruise control
below a speed of 20 mph (30 km/h).If traffic conditions allow, drive faster than 20 mph (30 km/h)
and save the speed.
Cruise control
- - - km/h
(Canada only)
The automatic transmission* is in position
P, R or N.Move the gear selector lever to positionD (page 140).
ESP® is switched off.Switch on ESP® (page 64).
The system is overheated.Wait until the system cools down.
Cruise Control and
Speedtronic
InoperativeCruise control is malfunctioning. In addition
a warning chime sounds.Have the cruise control checked at an authorized
Mercedes-Benz Center.
Check,
Tire Pressure
Then Restart
Run Flat Indicator
(Canada only)
There was a warning message about a loss
in tire inflation pressure and the Run Flat In-
dicator has not been restarted yet.Make sure the correct tire inflation pressure is set for each
tire (
page 339).
Then restart the Run Flat Indicator (page 343).
Run Flat
Indicator
Inoperative
(Canada only)
Run Flat Indicator is malfunctioning.Have the Run Flat Indicator checked at an authorized
Mercedes-Benz Center.

391 Practical hints
What to do if …?
Display Possible cause/consequencePossible solution
Check
Tire Pressure Soon
(Canada only)
The Run Flat Indicator indicates that the
pressure is too low in one or more tires.Carefully bring the vehicle to a halt, avoiding abrupt steering
and braking maneuvers. Observe the traffic situation around
you.
Check and adjust the tire inflation pressure as required
(
page 339).
If necessary, change the wheel (page 440).
Restart the Run Flat Indicator after adjusting the tire inflation
pressure values (
page 343).
Warning!G
Do not drive with a flat tire. A flat tire affects
the ability to steer or brake the vehicle. You
may lose control of the vehicle. Continued
driving with a flat tire will cause excessive
heat build-up and possibly a fire.

441 Practical hints
Flat tire
Mounting the Minispare wheel
Preparing the vehicle
Prepare the vehicle as described
(
page 440).
Take vehicle tool kit tray and vehicle
jack out of trunk (
page 420).
Take the Minispare wheel from the
wheel well under the trunk floor
(
page 422).Lifting the vehicle
Warning!G
When jacking up the vehicle, only use the
jack which has been specifically approved
by Mercedes-Benz for your vehicle.
The jack is designed exclusively for jacking
up the vehicle at the jack take-up brackets
built into both sides of the vehicle. Make
sure the jack arm is fully seated in the jack
take-up bracket.
The jack is intended only for lifting the
vehicle briefly for wheel changes. It is not
suited for performing maintenance work
under the vehicle. To help avoid personal
injury, use the jack only to lift the vehicle
during a wheel change.
Never get beneath the vehicle while it is sup-
ported by the jack. Keep hands and feet
away from the area under the lifted vehicle.
Always lower the vehicle onto sufficient
capacity jackstands before working under
the vehicle.
Always firmly set the parking brake and
block wheels with wheel chocks or other
sizeable objects before raising vehicle with
jack. Do not release the parking brake while
the vehicle is raised.
Make sure that the ground on which the
vehicle is standing and where you place the
jack is solid, level and not slippery. If neces-
sary, use a large underlay. On slippery
surfaces, such as tiled floors, you should
use a non-slip underlay, for example a
rubber mat.
Do not use wooden blocks or similar objects
to support the jack. Otherwise the jack may
not be able to achieve its load-bearing
capacity if it is not at its full height.
Be certain that the jack is always vertical
(plumb line) when in use, especially on hills.
Always try to use the jack on level surface.
Never start the engine when the vehicle is
raised.
Also observe the notes on the jack.

445 Practical hints
Flat tire
Guide the Minispare wheel onto the
wheel hub and push it on.
Insert wheel bolts and tighten them
slightly.
Lowering the vehicle
Lower vehicle by turning crank
counterclockwise until vehicle is
resting fully on its own weight.
Remove the jack.1 - 5 Wheel bolts
6 Wheel wrench
Tighten the five wheel bolts evenly,
following the diagonal sequence
illustrated (1 to 5), until all bolts are
tight. Observe a tightening torque of
96 lb-ft (130 Nm).
Before storing the jack, it should be fully
collapsed, with handle folded in (storage
position).
Store the jack and the other vehicle
tools in the designated storage space
underneath the trunk floor
(
page 420).
Warning!G
Have the tightening torque checked after
changing a wheel. The wheels could come
loose if they are not tightened to a torque of
96 lb-ft (130 Nm).
iVehicles with TPMS (USA only):
Do not activate the tire inflation pressure
monitor (
page 344) until a full size wheel/tire
with functioning sensor has been placed back
into service on the vehicle.

453 Practical hints
Towing the vehicle
Towing the vehicle
Mercedes-Benz recommends that the
vehicle be transported with all wheels off
the ground using flatbed or appropriate
wheel lift/dolly equipment. This method is
preferable to other types of towing.When circumstances do not permit the
recommended towing methods, the
vehicle may be towed with all wheels on
the ground or front wheels raised (except
vehicles with 4MATIC) only so far as neces-
sary to have the vehicle moved to a safe
location where the recommended towing
methods can be employed.
When towing the vehicle with all wheels on
the ground or the front axle raised (not per-
missible for vehicles with 4MATIC), the ve-
hicle may be towed only for distances up to
30 miles (50 km) and at a speed not to ex-
ceed 30 mph (50 km/h).
!Vehicles with automatic transmission*
and/or 4MATIC:
Do not tow-start the vehicle.
!Use flatbed or wheel lift/dolly equipment
with SmartKey or SmartKey with KEYLESS-GO*
(Canada only) in starter switch turned to
position0.
Do not tow with sling-type equipment. Towing
with sling-type equipment over bumpy roads will
damage radiator and supports.
To prevent damage during transport, do not tie
down vehicle by its chassis or suspension parts.
Switch off the ESP
® (page 63) and the auto-
matic central locking (
page 173).
!Vehicles with 4MATIC:
Do not tow with one axle raised. Doing so could
damage the transfer case, which is not covered
by the Mercedes-Benz Limited Warranty.
All wheels must be on or off the ground. Observe
instructions for towing the vehicle with all
wheels on the ground.
Warning!G
If circumstances require towing the vehicle
with all wheels on the ground, always tow
with a tow bar if:

the engine will not run

there is a malfunction in the brake
system

there is a malfunction in the power
supply or in the vehicle’s electrical
system
This is necessary to adequately control the
towed vehicle.
Prior to towing the vehicle with all wheels on
the ground, make sure the SmartKey or
SmartKey with KEYLESS-GO* (Canada only)
is in starter switch position2.

492 Index
Dual-zone automatic climate control
Maximum cooling MAX COOL 256
Dual-zone automatic climate control see
Climate control system
E
Easy-entry/exit feature*
(Canada only) 95, 174
EBP 61
Electrical fuses see Fuses
Electrical outlet
Glove box 293
Rear passenger compartment 293
Electrical system, Technical Data 473
Electronic Brake Proportioning see EBP
Electronic Stability Program see ESP
®
Electronic traction system 63
Emergency call system 295
Emergency calls, Tele Aid* 296
Emergency operation (Limp-Home
Mode) 146Emergency operations
Gear selector lever*, Unlocking 426
Locking the vehicle 424
Releasing from inside 271
Remote door lock* 302
Remote door unlock* 301
Unlocking the trunk 425
Unlocking the vehicle 424
Emergency tensioning device see ETD
Emergency, In case of
Battery, Jump starting 451
First aid kit 420
Flat tire 440
Fuses 456
Instrument cluster, Indicator
lamps 374–383
Roadside Assistance 12
Roadside Assistance* (Tele
Aid*) 299
Towing the vehicle 453
Emission control 320
Emission control information label 463
Emission control system warranties 10Engine
Adding engine oil 328
Belt layout 464
Cleaning 366
Compartment 325
Coolant 329, 478, 484
Malfunction indicator lamp 27, 378
Number 462, 463
Oil 327, 476, 480
Residual heat and ventilation 266
Starting 127
Technical data 465
Turning off 134
Engine coolant see Coolant
Engine oil 327
Adding 328
Additives 480
Checking level (Dipstick) 327
Consumption 327
Dipstick 327
Filler neck 327, 328
Recommended engine oils and oil
filters 476