2008 MAZDA MODEL TRIBUTE power steering

•If the vehicle goes from one type of surface to another (i.e., from
concrete to gravel) there will be a change in the way the vehicle
responds to a maneuver (steering, acceleration or braking). Again,
avoid these abrupt inputs.
Sand
When driving over sand, try to keep all four wheels on the most solid
area of the trail. Avoid reducing the tire pressures but shift to a lower
gear and drive steadily through the terrain. Apply the accelerator slowly
and avoid spinning the wheels.
Avoid excessive speed because vehicle momentum can work against you
and cause the vehicle to become stuck to the point that assistance may
be required from another vehicle. Remember, you may be able to back
out the way you came if you proceed with caution.
Mud and water
NOTE:
• If you must drive through high
water, drive slowly. Traction or
brake capability may be limited.
• When driving through water,
determine the depth; avoid water
higher than the bottom of the
hubs (if possible) and proceed
slowly. If the ignition system gets wet, the vehicle may stall.
• Once through water, always try the brakes. Wet brakes do not stop the
vehicle as effectively as dry brakes. Drying can be improved by moving
your vehicle slowly while applying light pressure on the brake pedal.
Be cautious of sudden changes in vehicle speed or direction when you
are driving in mud. Even 4WD vehicles can lose traction in slick mud. As
when you are driving over sand, apply the accelerator slowly and avoid
spinning your wheels. If the vehicle does slide, steer in the direction of
the slide until you regain control of the vehicle.
After driving through mud, clean off residue stuck to rotating
driveshafts, halfshafts and tires. Excess mud on tires and rotating
driveshafts causes an imbalance that could damage drive
components.
NOTE:
If the transaxle Power Take Off unit or rear axle are submerged in water,
their fluids should be checked and changed, if necessary.
2008 Tribute (j14)
Owners Guide (post-2002-fmt)
USA (fus)
Driving
184

Descend a hill in the same gear you
would use to climb up the hill to
avoid excessive brake application
and brake overheating. Do not
descend in neutral; instead,
disengage overdrive or manually
shift to a lower gear. When
descending a steep hill, avoid
sudden hard braking as you could
lose control. When you brake hard,
the front wheels can’t turn and if
they aren’t turning, you won’t be
able to steer. The front wheels have to be turning in order to steer the
vehicle. Rapid pumping of the brake pedal will help you slow the vehicle
and still maintain steering control.
If your vehicle has anti-lock brakes, apply the brakes steadily. Do not
“pump” the brakes.
Driving on snow and ice
• 4WD vehicles have advantages over 2WD vehicles in snow and ice but
can skid like any other vehicle.
• Should you start to slide while driving on snowy or icy roads, turn the
steering wheel in the direction of the slide until you regain control.
• Avoid sudden applications of power and quick changes of direction on
snow and ice. Apply the accelerator slowly and steadily when starting
from a full stop.
• Avoid sudden braking as well. Although a 4WD vehicle may accelerate
better than a two-wheel drive vehicle in snow and ice, it won’t stop
any faster, because as in other vehicles, braking occurs at all four
wheels. Do not become overconfident as to road conditions.
• Make sure you allow sufficient distance between you and other
vehicles for stopping. Drive slower than usual and consider using one
of the lower gears. In emergency stopping situations, avoid locking of
the wheels. Use a “squeeze” technique, push on the brake pedal with a
steadily increasing force which allows the wheels to brake yet
continue to roll so that you may steer in the direction you want to
travel. If you lock the wheels, release the brake pedal and repeat the
squeeze technique. Since your vehicle is equipped with a Four Wheel
Anti-Lock Brake System (ABS), apply the brake steadily. Do not
“pump” the brakes. Refer to the Brakessection of this chapter for
additional information on the operation of the anti-lock brake system.
2008 Tribute (j14)
Owners Guide (post-2002-fmt)
USA (fus)
Driving
186

Fuse/Relay Location Fuse Amp
Rating Passenger Compartment Fuse
Panel Description
16 15A Not used (spare)
17 20A All lock motor feeds, Liftgate release, Liftglass release
18 20A Heated seat
19 25A Rear wiper
20 15A Datalink
21 15A Fog lamps
22 15A Park lamps
23 15A High beam headlamps
24 20A Horn relay
25 10A Demand lamps
26 10A Instrument panel cluster
27 20A Ignition switch
28 5A Radio
29 5A Instrument panel cluster
30 5A Overdrive cancel
31 10A Not used (spare)
32 10A Restraints control module
33 10A Speed control switch
34 5A Speed control deactivate switch, ABS
35 10A Four wheel drive, EPAS (steering)
36 5A PATS transceiver
37 10A Climate control
38 20A
Subwoofer/Amp (Audiophile radio)
39 20A Radio
40 20A Front power point
41 15A Driver/passenger door lock switches
42 10A Not used (spare)
43 10A Rear wiper logic, Heated seats relay
2008 Tribute (j14)
Owners Guide (post-2002-fmt)
USA (fus)
Roadside Emergencies
192

Maintenance Item Maintenance Interval (Number of months or km (miles),
whichever comes first)
Months 6 12 18 24 30 36 42 48 54 60 66 72
x 1000 Miles 7.5 15 22.5 30 37.5 45 52.5 60 67.6 75 82.5 90
(x 1000 Km) (12) (24) (36) (48) (60) (72) (84) (96)
(108) (120) (132) (144)
CHASSIS and BODY
Brake lines, hoses and connections I I I
Disc brakes IIIIII
Drum brakes I I I
Tire (rotation),
check wheel lug nut torque*3 Rotate every 7,500 miles (12,000 km)
Tire inflation and wear IIIIIIIIIIII
Steering operation and linkages I I I
Power steering fluid level IIIIIIIIIIII
Manual transaxle fluid Replace every 100,000 miles (160,000 km)
Automatic transaxle fluid Replace every 150,000 miles (240,000 km)
Rear differential fluid
(4WD only) *2 Replace every 150,000 miles (240,000 km)
Transfer case fluid
(4WD only) Replace every 150,000 miles (240,000 km)
Front and rear suspension ball
joints III
Driveshaft dust boots I I I
Bolts and nuts on chassis and body I I I
Exhaust system heat shields I I I
All locks and hinges L L L L L L L L L L L L
Washer fluid level IIIIIIIIIIII
*1 According to state and federal regulations, failure to perform maintenance on these
items will not void your emissions warranties. However, Mazda recommends that all
maintenance services be performed at the recommended time or miles (kilometers)
period to ensure long-term reliability. Refer to Fuel filterin theMaintenance and
Specifications chapter for fuel filter replacement requirements.
*2 If this component has been submerged in water, the oil should be changed.
*3 The wheel lug nuts must be retightened to the proper specifications at 500 miles
(800 km) of new vehicle operation, at any wheel change, or at any other time the
wheel lug nuts have been loosened. Refer to Wheel Lug Nut Torque Specificationin
the Tires, Wheels and Loading chapter for the proper lug nut torque specification.
2008 Tribute(j14)
Owners Guide (post-2002-fmt)
USA (fus)
Maintenance and Specifications
234

Maintenance Item Maintenance Interval (Number of months or km (miles),
whichever comes first)
Months 4 8 12 16 20 24 28 32 36 40 44 48
x 1000 miles 5 10 15 20 25 30 35 40 45 50 55 60
(x 1000 Km) (8) (16)
(24)(32) (40) (48) (56) (64) (72) (80) (88) (96)
ELECTRICAL SYSTEM
Function of all lights I I I IIIIIIIII
CHASSIS and BODY
Brake lines, hoses and connections I I
Brake fluid level I I I IIIIIIIII
Disc brakes I I I I
Drum brakes I I
Tire (rotation),
check wheel lug nut torque *4 Rotate every 5,000 miles (8,000 km)
Tire inflation pressure and tire wearIIIIIIIIIIII
Steering operation and linkages I I
Power steering fluid level I I I IIIIIIIII
Manual transaxle oil Replace every 100,000 miles (160,000 km)
Automatic transaxle fluid Replace every 30,000 miles (48,000 km)
Rear differential
fluid (4WD only) *3 Replace every 100,000 miles (160,000 km)
Transfer case fluid
(4WD only) *3 Replace every 30,000 miles (48,000 km)
Front and rear suspension ball
joints II
Driveshaft dust boots I I
Bolts and nuts on chassis and body I I I I
Exhaust system heat shields I I
All locks and hinges L L L LLLLLLLLL
Washer fluid level I I I IIIIIIIII
*1 According to state and federal regulations, failure to perform maintenance on these
items will not void your emissions warranties. However, Mazda recommends that all
maintenance services be performed at the recommended time or miles (kilometers)
period to ensure long-term reliability. Refer to Fuel filterin theMaintenance and
Specifications chapter for fuel filter replacement requirements.
2008 Tribute(j14)
Owners Guide (post-2002-fmt)
USA (fus)
Maintenance and Specifications
236

*2 If the vehicle is operated under any of the following conditions, change the spark
plugs every 60,000 miles (96,000 km) or shorter.
a) Repeated short-distance driving.
b) Extended periods of idling or low-speed operation.
c) Driving for long periods in cold temperatures or extremely humid climates.
*3 If this component has been submerged in water, the oil should be changed.
*4 The wheel lug nuts must be retightened to the proper specifications at 500 miles
(800 km) of new vehicle operation, at any wheel change, or at any other time the
wheel lug nuts have been loosened. Refer to Wheel Lug Nut Torque Specificationin
the Tires, Wheels and Loading chapter for the proper lug nut torque specification.
OWNER MAINTENANCE SCHEDULE
The owner or a qualified service technician should make these vehicle
inspections at the indicated intervals to ensure safe and dependable
operation.
Bring any problem to the attention of an authorized Mazda Dealer or
qualified service technician as soon as possible.
When Refueling
• Brake and clutch fluid level
• Engine coolant level
• Engine oil level
• Washer fluid level
At Least Monthly
• Tire inflation pressures
At Least Twice a Year (For Example, Every Spring and Fall)
• Automatic transaxle fluid level
• Power steering fluid level
Retightening lug nuts
• Retighten the lug nuts to the specified torque at 500 miles (800 km)
after any wheel disturbance (tire rotation, changing a flat tire, wheel
removal, etc.).
• Refer to Wheel Lug Nut Torque Specification in theTires, Wheels
and Loading chapter for the proper lug nut torque specification.
2008 Tribute(j14)
Owners Guide (post-2002-fmt)
USA (fus)
Maintenance and Specifications
237

•NEVER decrease the coolant concentration below 40%.
• Decreased engine coolant concentrations below 40% will
decrease the corrosion protection characteristics of the engine
coolant and may cause engine damage.
• Decreased engine coolant concentrations below 40% will
decrease the freeze protection characteristics of the engine
coolant and may cause engine damage.
• Refer to the chart on the coolant container to ensure the
coolant concentration in your vehicle will provide adequate
protection at the temperatures in which you drive.
Vehicles driven year-round in non-extreme climates should use a 50/50
mixture of engine coolant and distilled water for optimum cooling system
and engine protection.
What you should know about fail-safe cooling (2.3L I4 engine only)
If the engine coolant supply is depleted, this feature allows the vehicle to
be driven temporarily before incremental component damage is incurred.
The “fail-safe” distance depends on ambient temperatures, vehicle load
and terrain.
How fail-safe cooling works
If the engine begins to overheat:
• The engine coolant temperature gauge will move to the red (hot)
area.
• The
indicator light will illuminate.
If the engine reaches a preset over-temperature condition, the engine
will automatically switch to alternating cylinder operation. Each disabled
cylinder acts as an air pump and cools the engine.
When this occurs the vehicle will still operate. However:
• The engine power will be limited.
• The air conditioning system will be disabled.
Continued operation will increase the engine temperature and the engine
will completely shut down, causing steering and braking effort to
increase.
Once the engine temperature cools, the engine can be re-started. Take
your vehicle to an authorized dealer as soon as possible to minimize
engine damage.
2008 Tribute (j14)
Owners Guide (post-2002-fmt)
USA (fus)
Maintenance and Specifications
255

Child safety seats - booster
seats ...........................................114
Cleaning your vehicle engine compartment ..............227
instrument panel ....................229
interior .....................................230
Mazda car care products .......231
plastic parts ............................228
washing ....................................226
waxing .....................................226
wheels ......................................227
wiper blades ............................229
Climate control (see Air
conditioning or Heating) ............29
Clutch fluid ..........................................267
operation while driving ..........179
recommended shift speeds ....180
Console ........................................44 overhead ....................................44
Controls power seat .................................74
steering column ........................52
Coolant checking and adding ..............250
refill capacities ................254, 271
specifications ..........................271
Cruise control .............................49
Cruise control
(see Speed control) ....................49
Customer
Assistance ..................215–216, 219
D
Daytime running lamps
(see Lamps) ................................33 Dipstick
automatic transmission
fluid ..........................................267
engine oil .................................244
Driving under special
conditions ..................178, 182, 185 sand .........................................184
snow and ice ...........................186
through water .................184, 187
E
Electronic stability control ......168
Emergencies, roadside jump-starting ..........................207
Emergency Flashers .................188
Emission control system ..........264
Engine ........................................273 cleaning ...................................227
coolant .....................................250
fail-safe cooling .......................255
idle speed control ...................248
lubrication specifications .......271
refill capacities ........................271
service points ..................240–241
starting after a collision .........189
Engine block heater .................165
Engine oil ..................................244 checking and adding ..............244
dipstick ....................................244
filter, specifications ................247
recommendations ...................247
refill capacities ........................271
specifications ..........................271
Exhaust fumes ..........................164
F
Fail safe cooling ........................255
Fluid capacities .........................271
2008 Tribute (j14)
Owners Guide (post-2002-fmt)
USA (fus)
Index
278