2008 MAZDA MODEL TRIBUTE warning

BRAKES
Occasional brake noise is normal. If a metal-to-metal, continuous grinding
or continuous squeal sound is present, the brake linings may be worn-out
and should be inspected by an authorized dealer. If the vehicle has
continuous vibration or shudder in the steering wheel while braking, the
vehicle should be inspected by an authorized dealer.
Refer to Brake system warning
light in the Instrument Cluster
chapter for information on the brake
system warning light.
Four-wheel anti-lock brake system (ABS)
Since your vehicle is equipped with an Anti-lock Braking System (ABS),
a noise from the hydraulic pump motor and pulsation in the pedal may
be observed during ABS braking events. Pedal pulsation coupled with
noise while braking under panic conditions or on loose gravel, bumps,
wet or snowy roads is normal and indicates proper functioning of the
vehicle’s anti-lock brake system.
NOTE: The ABS performs a self-check after you start the engine and
begin to drive away.
A brief mechanical noise may be heard during this test. This is normal. If
a malfunction is found, the ABS warning light will come on. If the vehicle
has continuous vibration or shudder in the steering wheel while braking,
the vehicle should be inspected by an authorized dealer.
The ABS operates by detecting the
onset of wheel lockup during brake
applications and compensates for
this tendency. The wheels are
prevented from locking even when
the brakes are firmly applied. The
accompanying illustration depicts
the advantage of an ABS equipped
vehicle (on bottom) to a non-ABS
equipped vehicle (on top) during hard braking with loss of front braking
traction.
WARNING: The Anti-Lock system does not decrease the time
necessary to apply the brakes or always reduce stopping
distance. Always leave enough room between your vehicle and
the vehicle in front of you to stop.
P!
BRAKE
2008 Tribute (j14)
Owners Guide (post-2002-fmt)
USA (fus)
Driving
166

Using ABS
When hard braking is required, apply continuous force on the brake
pedal; do not pump the brake pedal since this will reduce the
effectiveness of the ABS and will increase your vehicle’s stopping
distance. The ABS will be activated immediately, allowing you to retain
steering control during hard braking and on slippery surfaces. However,
the ABS does not decrease stopping distance.
ABS warning lamp
The ABS lamp in the instrument
cluster momentarily illuminates
when the ignition is turned on. If
the light does not illuminate during
start up, remains on or flashes, the
ABS may be disabled and may need to be serviced.
Even when the ABS is disabled,
normal braking is still effective. (If
your BRAKE warning lamp
illuminates with the parking brake
released, have your brake system
serviced immediately by an authorized dealer.)
Parking brake
Apply the parking brake whenever
the vehicle is parked. To set the
parking brake, press the parking
brake pedal down until the pedal
stops.
The BRAKE warning lamp in the
instrument cluster illuminates and
remains illuminated (when the
ignition is turned ON) until the
parking brake is released.
ABS
P!
BRAKE
P!
BRAKE
2008 Tribute (j14)
Owners Guide (post-2002-fmt)
USA (fus)
Driving
167

WARNING: Always set the parking brake fully and make sure
that the gearshift is securely latched in P (Park) (automatic
transmission) or in 1 (First) (manual transmission).
NOTE: The parking brake is not recommended to stop a moving vehicle.
However, if the normal brakes fail, the parking brake can be used to stop
your vehicle in an emergency. Since the parking brake applies only the
rear brakes, the vehicle’s stopping distance will increase greatly and the
handling of your vehicle will be adversely affected.
Pull the release lever to release the
brake.
Driving with the parking brake
on will cause the brakes to wear
out quickly and reduce fuel
economy.
ELECTRONIC STABILITY CONTROL (ESC) SYSTEM
The Electronic Stability Control (ESC) system provides stability
enhancement features such as Roll Stability Control (RSC), Dynamic
Stability Control (DSC) and Traction Control (TCS) for certain driving
situations. The system includes an on/off button, and a “sliding car” icon
in the instrument cluster.
Some drivers may notice a slight movement of the brake pedal when the
ESC system performs a system self-check. During ESC system operation
you may experience the following:
• A rumble, grunting, or grinding noise after startup and when driving
off
• A slight deceleration of the vehicle
• The ESC system indicator light will flash when the system is activated.
• If your foot is on the brake pedal, you will feel a vibration in the
pedal.
2008 Tribute (j14)
Owners Guide (post-2002-fmt)
USA (fus)
Driving
168

•Entering a snow-free road from a snow-covered side street, or vice
versa.
• Entering a paved road from a gravel road, or vice versa.
• Driving on slick surfaces.
• Cornering while towing a heavily loaded trailer (refer to Trailer
towing in theTires, Wheels and Loading chapter.)
Roll Stability Control (RSC)
The RSC system works in conjunction with the ESC system to help
maintain roll stability of the vehicle during aggressive maneuvers by
applying brake force to one or more wheels.
During Roll Stability Control (RSC) events the “sliding car” icon in the
instrument cluster will flash momentarily.
Driving conditions that may activate ESC include:
• Emergency lane-change
• Taking a turn too fast
• Quick maneuvering to avoid an accident, pedestrian or obstacle
Electronic Stability Control (ESC) button and icon functionality
The ESC system automatically turns on each time the engine is started,
even if it was turned off when the engine was last shut down. The
“sliding car” icon which is located with the warning lights in the
instrument cluster will illuminate during bulb check at initial start-up and
then go off. This tells you that the system is normal and active. All
functions of the ESC system (RSC, DSC, and TCS) will be activated at
start up. When the system is left active, the “sliding car” icon will flash
only when any of the components of the system are affecting the
vehicle’s performance, otherwise the light will remain off. Consequently,
the “sliding car” icon will not be illuminated during most of your normal
driving.
The ESC button, located on the
center stack of the instrument
panel, allows the driver to control
certain features of the ESC system
below 25 mph (40 km/h). If the
vehicle is below 25 mph (40 km/h),
momentarily pressing the ESC button will disable RSC, DSC and Engine
Traction Control and steadily illuminate the “sliding car” icon. Pressing
and holding the ESC button for more than five seconds will further
disable the brake portion of the Traction Control feature and the “sliding
car” icon will flash momentarily and then illuminate steady.
2008 Tribute (j14)
Owners Guide (post-2002-fmt)
USA (fus)
Driving
170

If the vehicle is above 25 mph (40 km/h), momentarily pressing the ESC
button will steadily illuminate the “sliding car” icon, however, the ESC
system will remain enabled until the vehicle speed drops below 25 mph.
If the vehicle speed decreases below 25 mph (40 km/h), the system will
become deactivated, but if the vehicle speed subsequently increases to
above 25 mph (40 km/h), the system will again become active. In
general, the system will be active at all times the vehicle speed is above
25 mph (40 km/h).
In R (Reverse), ABS and the Traction Control feature will continue to
function, however ESC and RSC are disabled.
All these conditions are normal during ESC system operation. Refer to
the following table.
Electronic Stability Control Features
Button
functions “Sliding
car” icon RSC DSC Engine
Traction Control Brake
Traction Control
Default at
start-up Illuminated
during bulb check Enabled Enabled Enabled Enabled
Button
pressed
momentarily Illuminated
solid Disabled
below
25 mph
(40 km/h)
Disabled below
25 mph
(40 km/h)
Disabled below
25 mph
(40 km/h) Enabled
Button
pressed and
held more
than five
seconds Flashes
then
illuminated solid Disabled
below
25 mph
(40 km/h)
Disabled below
25 mph
(40 km/h)
Disabled below
25 mph
(40 km/h) Disabled
below
25 mph
(40 km/h)
WARNING: Do not alter or modify your vehicle’s suspension or
steering; the resulting changes to the vehicle’s handling can
adversely affect the Electronic Stability Control (ESC) system.
2008 Tribute (j14)
Owners Guide (post-2002-fmt)
USA (fus)
Driving
171

WARNING: Aggressive driving in any road conditions can cause
you to lose control of your vehicle increasing the risk of severe
personal injury or property damage. The occurrence of a
Electronic Stability Control (ESC) event is an indication that
at least some of the tires have exceeded their ability to grip the
road; this may lead to an increased risk of loss of vehicle
control, vehicle rollover, personal injury and death. If you
experience a severe road event, SLOW DOWN.
If a failure is detected in the ESC system, and the ESC button has not
been pushed, the warning indicator light in the instrument cluster will
stay on. If the warning indicator light in the instrument cluster remains
on while the engine is running, have the system serviced by an
authorized dealer immediately.
STEERING
Your vehicle is equipped with an Electric Power-Assisted Steering
(EPAS) system. There is no fluid reservoir to check or fill.
If your vehicle loses electrical power while you are driving (or if the
ignition is turned off), you can steer the vehicle manually, but it takes
more effort. Under extreme usage conditions, the steering effort may
increase. This occurs to prevent overheating and permanent damage to
your steering system. If this should occur, you will neither lose the ability
to steer the vehicle manually nor will it cause permanent damage.
Typical steering and driving maneuvers will allow the system to cool and
steering assist will return to normal.
If the steering wanders or pulls, check for:
• an improperly inflated tire
• uneven tire wear
• loose or worn suspension components
• loose or worn steering components
• improper steering alignment
A high crown in the road or high crosswinds may also make the steering
seem to wander/pull.
2008 Tribute (j14)
Owners Guide (post-2002-fmt)
USA (fus)
Driving
172

PREPARING TO DRIVE WARNING: Utility vehicles have a significantly higher rollover
rate than other types of vehicles.
WARNING:
In a rollover crash, an unbelted person is significantly
more likely to die than a person wearing a seat belt.
Utility vehicles and trucks have larger tires and increased ground
clearance, giving the vehicle a higher center of gravity than a passenger
car.
WARNING: Vehicles with a higher center of gravity such as
utility vehicles and trucks handle differently than vehicles with
a lower center of gravity. Utility vehicles and trucks are not
designed for cornering at speeds as high as passenger cars any
more than low-slung sports cars are designed to perform
satisfactorily under off-road conditions. Avoid sharp turns,
excessive speed or abrupt maneuvers in these vehicles. Failure
to drive cautiously could result in an increased risk of loss of
vehicle control, vehicle rollover, personal injury and death.
WARNING: Loaded vehicles, with a higher center of gravity,
may handle differently than unloaded vehicles. Do not overload
your vehicle and use extra precautions, such as driving at
slower speeds, avoiding abrupt steering changes and allowing
for increased stopping distance, when driving a heavily loaded
vehicle. Over loading or loading the vehicle improperly can
deteriorate handling capability and contribute to loss of vehicle
control and vehicle rollover.
AUTOMATIC TRANSMISSION OPERATION (IF EQUIPPED)
Brake-shift interlock
This vehicle is equipped with a brake-shift interlock feature that prevents
the gearshift lever from being moved from P (Park) when the ignition is
in the RUN position unless brake pedal is depressed.
If you cannot move the gearshift lever out of P (Park) with ignition in
the RUN position and the brake pedal depressed, it is possible that a
fuse has blown or the vehicle’s brakelamps are not operating properly.
Refer to Fuses and relays in theRoadside Emergencies chapter.
2008 Tribute(j14)
Owners Guide (post-2002-fmt)
USA (fus)
Driving
173

If the fuse is not blown, perform the following procedure: 1. Apply the parking brake, turn the ignition to LOCK, then remove the key.
2. Using a screwdriver or similar tool, carefully pry out the small
Brake Transmission Shift
Interlock (BTSI) cover cap
located to the right of the
gearshift lever.
3. Insert a screwdriver or similar tool straight down into the
access hole and press downward
while pulling the gearshift lever
out of the P (Park) position and
into the N (Neutral) position.
4. Remove tool and reinstall the BTSI cover cap.
5. Start the vehicle and release the parking brake.
WARNING: Do not drive your vehicle until you verify that the
brakelamps are working.
WARNING: Always set the parking brake fully and make sure
the gearshift is latched in P (Park). Turn the ignition to the
LOCK position and remove the key whenever you leave your
vehicle.
WARNING: If the parking brake is fully released, but the brake
warning lamp remains illuminated, the brakes may not be
working properly. See your authorized dealer as soon as
possible.
2008 Tribute (j14)
Owners Guide (post-2002-fmt)
USA (fus)
Driving
174