2008 MAZDA MODEL TRIBUTE HEV maintenance

5. Using the hole in the splashshield, remove the check plug
from the side of the
transmission.
If this is the first check of the
transmission fluid, it may be
necessary to remove the perforated
section of the splash shield (as
indicated on the splash shield). 6. Be sure the engine has been stopped for at least 3 minutes before performing the fluid level check.
2008 Tribute Hybrid (thv)
Owners Guide (post-2002-fmt)
USA (fus)
Maintenance and Specifications
277

7. The fluid level should be within1/4 inch (6 mm) of the plug
threads.
8. Replace the check plug.
Adjusting eCVT fluid levels
Before adding any fluid, make sure the correct type is used. The type of
fluid used is indicated in the Maintenance product specifications and
capacities section in this chapter.
Use of a non-approved fluid may cause internal transaxle
component damage.
If the fluid level is low, add fluid through the check port until the level is
correct and fluid begins to run out of the transmission. If an overfill
occurs, excess fluid should be removed by allowing the fluid to run out
of the check port.
A serious overfill condition of transmission fluid may cause
damage.
Do not use supplemental transmission fluid additives, treatments or
cleaning agents. The use of these materials may affect transmission
operation and result in damage to internal transmission components.
AIR FILTER
Refer to scheduled maintenance information for the appropriate
intervals for changing the air filter element.
When changing the air filter element, use only the Mazda air filter
element listed. Refer to Mazda part numbersin this chapter.
WARNING: To reduce the risk of vehicle damage and/or
personal burn injuries do not start your engine with the air
cleaner removed and do not remove it while the engine is
running.
2008 Tribute Hybrid (thv)
Owners Guide (post-2002-fmt)
USA (fus)
Maintenance and Specifications
278

Changing the air filter element1. Release the clamps that secure the air filter housing cover.
2. Carefully separate the two halves of the air filter housing.
3. Remove the air filter element from the air filter housing.
4. Wipe the air filter housing and cover clean to remove any dirt or debris and to ensure good sealing.
5. Install a new air filter element. Be careful not to crimp the
filter element edges between
the air filter housing and cover.
This could cause filter damage
and allow unfiltered air to enter
the engine if not properly
seated.
6. Replace the air filter housing cover and secure the clamps.
Note: Failure to use the correct air filter element may result in severe
engine damage. The customer warranty may be voided for any damage to
the engine if the correct air filter element is not used.
HIGH VOLTAGE BATTERY COOLING FILTER (REAR A/C)
MAINTENANCE
The high voltage battery has a dedicated A/C cooling system which
includes an air filter.
Refer to the scheduled maintenance information for the appropriate
intervals for air filter.
When changing the air filter element, use only the Mazda air filter
element listed. Refer to Mazda part numbersin this chapter.
2008 Tribute Hybrid(thv)
Owners Guide (post-2002-fmt)
USA (fus)
Maintenance and Specifications
279

Changing the high voltage battery air filter element1. Remove access panel located in the rear cargo area on the
driver’s side trim panel to
expose the filter cover.
2. Push the tabs (located on each side of filter cover) while pulling
gently to remove filter cover.
3. Install new filter and filter cover (note arrows indicating top side).
4. Re-install the access panel into the trim panel.
2008 Tribute Hybrid (thv)
Owners Guide (post-2002-fmt)
USA (fus)
Maintenance and Specifications
280

MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIES
ItemCapacityMazda Part Name or
equivalent Application
Brake fluid Between MIN and
MAX lines on reservoir High Performance DOT 3
Motor Vehicle Brake Fluid Brake fluid reservoir
Engine coolant 8.5 quarts (8.0L) Mazda Premium Engine
Coolant
1
Cooling systems
Motor/Electronics (M/E)
Coolant 3.7 quarts (3.5L)
Engine oil 4.5 quarts (4.25L) SAE 5W-20 Motor Oil Engine
Automatic eCVT transaxle fluid 5.3 quarts (5.0L)
2
MERCON
VATF
3
Transaxle
Rear axle fluid (4WD) 2.96 pints (1.4L)
4
API service GL-5 SAE 80W-90
5
Rear axle
Power Transfer Unit fluid (4WD)
6
12 ounces (0.35L) API service GL-5
SAE 75W-140 Synthetic Lubricant Power transfer unit
Windshield washer fluid 2.7 quarts (2.6L) Ultra-clear Windshield
Washer Concentrate Washer fluid reservoir
2008 Tribute Hybrid
(thv)
Owners Guide (post-2002-fmt)
USA (fus)
Maintenance and Specifications
281

ItemCapacityMazda Part Name or
equivalent Application
Fuel tank 15 gallons (56.8L) — All
1Add the coolant type originally equipped in your vehicle. Refer to Adding engine coolantin this
chapter.2Indicates only approximate dry-fill capacity.3Using any transmission fluid other than those that meet the recommended specification may cause
internal transaxle damage. Do not use MERCON CVT (blue) ATF. This vehicle uses only
MERCON V ATF.4Fill to 1/4 inch to 9/16 inch (6mm to 14mm) below bottom of fill hole.54WD vehicles exposed for prolonged periods to temperatures less than -40° C (-40° F) should
change out the rear axle fluid to SAE 75W-140 axle lubricant.6The Power Transfer Unit is lubricated for life with synthetic lube. Lubricant levels are not to be
checked or changed unless a leak is suspected or repair required. Replace Power Transfer Unit
lubricant with specified synthetic lubricant anytime the unit is submerged in water.
2008 Tribute Hybrid (thv)
Owners Guide (post-2002-fmt)
USA (fus)
Maintenance and Specifications
282

ENGINE DATA
Engine2.3L I4 engine
Cubic inches 140
Required fuel 87 octane
Firing order 1-3-4-2
Ignition system Coil on plug
Spark plug gap 0.049–0.053 inch (1.25–1.35mm)
Compression ratio 12.3:1
Engine drivebelt routing
• 2.3L I4 Engine
HIGH VOLTAGE BATTERY DATA
High Voltage Battery
Battery chemistry Nickel Metal Hydride
Nominal Voltage 330 Volts
Capacity 6 Amp-hours
2008 Tribute Hybrid (thv)
Owners Guide (post-2002-fmt)
USA (fus)
Maintenance and Specifications
283

IDENTIFYING YOUR VEHICLE
Safety Compliance Certification Label
The National Highway Traffic Safety
Administration Regulations require
that a Safety Compliance
Certification Label be affixed to a
vehicle and prescribe where the
Safety Compliance Certification
Label may be located. The Safety
Compliance Certification Label is
located on the structure (B-Pillar)
by the trailing edge of the driver’s
door or the edge of the driver’s
door.
Vehicle identification number (VIN)
The vehicle identification number is
located on the driver side
instrument panel.
Please note that in the graphic,
XXXX is representative of your
vehicle identification number.
MFD. BY FORD MOTOR CO. IN U.S.A.
EXT PNT:XX RC: XXDSO:
WB BRK INT TR TP/PS R AXLE TR SPR XXXXX
XXX X XX X XX X XX \
XXX
XXXXXXXXXXXXX XXX XXXX-XXXXXXX-XX
THIS VEHICLE CONFORMS TO ALL APPLICABLE FEDERAL MOTOR
VEHICLE SAFETY AND THEFT PREVENTION STANDARDS IN
EFFECT ON THE DATE OF MANUFACTURE SHOWN ABOVE.
VIN: XXXXXXXXXXXXXXXXX XXXXX
TYPE: XXX XXXXX
DATE: XX/XX GVWR:XXXXXLB/ XXXXXKG
FRONT GAWR: XXXXL REAR GAWR: XXXXLB
AT XXX kPa/XX PSI COLD AT XXX kPa/XX PSI COLD XXXXKG
WITH
XXXX/XXXXXXX TIRES
XXXX.XX RIMSXXXXKG
WITH
XXXX/XXXXXXX TIRES
XXXX.XX RIMS
FOR MAZDA MOTOR CORPORATION
XXXXXXXXXXXXXXXXX
2008 Tribute Hybrid(thv)
Owners Guide (post-2002-fmt)
USA (fus)
Maintenance and Specifications
284