2008 MAZDA MODEL MX-5 MIATA POWER RETRACTABLE HARDTOP lights

Black plate (295,1)
(Cont.)Maintenance Interval Number of months or kilometers, whichever comes first
Months 39 42 45 48 51 54 57 60 63 66 69 72
×1000 km 65 70 75 80 85 90 95 100 105 110 115 120
ENGINE
Drive belts (tension) II
Engine valve clearance Audible inspect every 120,000 km, if noisy, adjust
Engine oil RRRRRRRRRRRR
Engine oil filter RRRRRRRRRRRR
COOLING SYSTEM
Cooling system II
Engine coolant FL22 type
*1Replace at first 190,000 km or 10 years; after that, every
60,000 km or 3 years
Others R R
Engine coolant level IIIIIIIIIIII
FUEL SYSTEM
Air filter CRCRCR
Fuel lines and hoses I
*2I
Hoses and tubes for emission I*2I
Fuel filter R R
IGNITION SYSTEM
Spark plugs Replace every 60,000 km
ELECTRICAL SYSTEM
Function of all lights IIIIIIIIIIII
Maintenance and Care
Scheduled Maintenance
8-13
MX-5_8X49-EA-07F_Edition5 Page295
Thursday, February 21 2008 12:51 AM
Form No.8X49-EA-07F

Black plate (319,1)
Light Bulbs
High-mount brake light
License plate lights
Trunk light Reverse lights
Rear turn signal lights
Brake lights / Taillights
Side-marker lights
Overhead light
Head lights (High beam)
Parking light
Front fog lights
Headlights (Low beam)
Front turn signal lights
Side-marker lights Some models.
Maintenance and Care
Owner Maintenance
8-37
MX-5_8X49-EA-07F_Edition5 Page319
Thursday, February 21 2008 12:52 AM
Form No.8X49-EA-07F

Black plate (323,1)
5. Disconnect the socket and bulbassembly from the electrical connector
by pressing the tab on the connector
with your finger and pulling it.
6. Install the new socket and bulbassembly in the reverse order of
removal.
NOTE
lIf the halogen bulb is accidentally touched,
it should be cleaned with rubbing alcohol
before being used.
lUse the protective cover and carton of the
replacement bulb to dispose of the old bulb
promptly out of the reach of children.
Front turn signal lights
1. If you are changing the right front turn signal light bulb, start the engine, turn
the steering wheel all the way to the
left, and turn off the engine. If you are
changing the left front turn signal light
bulb, turn the steering wheel to the
right. 2. Turn the screws counterclockwise and
remove them.
3. Turn the center section of the plastic
retainers counterclockwise and remove
them, then remove the mudguard.
Removal
Installation
4. Turn the socket and bulb assembly counterclockwise and remove it.
Maintenance and Care
Owner Maintenance
8-41
MX-5_8X49-EA-07F_Edition5 Page323
Thursday, February 21 2008 12:52 AM
Form No.8X49-EA-07F

Black plate (324,1)
5. Disconnect the bulb from the socket.
6. Install the new bulb in the reverse orderof removal.
Parking lights
1. Turn the socket and bulb assemblycounterclockwise and remove it.
2. Disconnect the bulb from the socket.
3. Install the new bulb in the reverse order of removal.
Front side-marker lights
NOTE
To replace the bulb, contact an Authorized
Mazda Dealer.
1. Slide the unit as shown in the figure toremove it.
2. Turn the socket and bulb assembly
counterclockwise and remove it.
3. Disconnect the bulb from the socket.
4. Install the new bulb in the reverse order of removal.
8-42
Maintenance and Care
Owner Maintenance
MX-5_8X49-EA-07F_Edition5 Page324
Thursday, February 21 2008 12:52 AM
Form No.8X49-EA-07F

Black plate (325,1)
Brake lights/Taillights, Rear turn signal
lights, Reverse lights
1. Pull the center section of the plasticretainers and remove them, then
remove the trunk end trim.
Removal
Installation
2. On the side the bulb is to be replaced, pull the center section of the plastic
retainers and remove them, then
remove the trunk side trim.
Removal
Installation
3. Turn the socket and bulb assembly counterclockwise and remove it. 4. Disconnect the bulb from the socket.
Brake lights/Taillights
Rear turn signal lights
Reverse lights
5. Install the new bulb in the reverse order of removal.
High-mount brake light
Due to the complexity and difficulty of
the procedure, the LED bulbs should be
replaced by an Authorized Mazda Dealer.
License plate lights
Due to the complexity and difficulty of
the procedure, the bulbs should be
replaced by an Authorized Mazda Dealer.
Maintenance and Care
Owner Maintenance
8-43
MX-5_8X49-EA-07F_Edition5 Page325
Thursday, February 21 2008 12:52 AM
Form No.8X49-EA-07F

Black plate (327,1)
Fuses
Your vehicle's electrical system is
protected by fuses.
If any lights, accessories, or controls don't
work, inspect the appropriate circuit
protector. If a fuse has blown, the inside
element will be melted.
If the same fuse blows again, avoid using
that system and consult an Authorized
Mazda Dealer as soon as possible.
qFuse Replacement
Replacing the fuses on the vehicle's left
side
If the electrical system does not work,
first inspect the fuses on the vehicle's left
side.
1. Turn off the ignition switch and other
switches.
2. Remove the cover.
3. Pull the fuse straight out with the fuse puller provided on the inside of the
engine compartment fuse block cover.
Fuse puller
Fuse block cover
4. Inspect the fuse and replace it if it'sblown.
Normal Blown
5. Insert a new fuse of the same amperage
rating, and make sure it fits tightly. If it
does not fit tightly, have an expert
install it. We recommend an
Authorized Mazda Dealer.
If you have no spare fuses, borrow one
of the same rating from a circuit not
essential to vehicle operation, such as
the MIRROR or CIGAR circuit.
CAUTION
Always replace a fuse with one of the
same rating. Otherwise you may
damage the electric system.
Maintenance and Care
Owner Maintenance
8-45
MX-5_8X49-EA-07F_Edition5 Page327
Thursday, February 21 2008 12:52 AM
Form No.8X49-EA-07F

Black plate (328,1)
Replacing the fuses under the hood
If the headlights or other electrical
components do not work and the fuses in
the cabin are normal, inspect the fuse
block under the hood. If a fuse is blown, it
must be replaced. Follow these steps:
1. Turn off the ignition switch and allother switches.
2. Remove the fuse block cover.
3. If any fuse but the MAIN fuse is blown, replace it with a new one of the
same amperage rating .
Normal
Blown
WARNING
Do not replace the main fuse by
yourself. Have an Authorized Mazda
Dealer perform the replacement:
Replacing the fuse by yourself is
dangerous because the MAIN fuse is
a high current fuse. Incorrect
replacement could cause an electrical
shock or a short circuit resulting in a
fire.
8-46
Maintenance and Care
Owner Maintenance
MX-5_8X49-EA-07F_Edition5 Page328
Thursday, February 21 2008 12:52 AM
Form No.8X49-EA-07F

Black plate (329,1)
qFuse Panel Description
Fuse block (Engine compartment)
DESCRIPTION FUSE
RATING PROTECTED COMPONENT
1 FAN 30 A Cooling fan
2 FAN 7.5 A Cooling fan
3 DEFOG 20 A Rear window defroster
4 H/CLEAN ――
5 ROOM 15 A Overhead lights, Luggage compartment light, For protection of
various circuits
6 IG KEY2 15 A For protection of various circuits
7 HEATER 40 A Air conditioner
í
8 ABS 30 A ABS
9 FOG 15 A Front fog lightsí
10R.FOG ――
11 RHT L 30 A Power retractable hardtop (LH)í
12 RHT R 30 A Power retractable hardtop (RH)í
13MAG 7.5 A Air conditionerí
14ST 20 A Starter
15 TAIL 15 A Taillights, Parking lights, License plate lights, illuminations
16 ABS 40 A ABS
Maintenance and Care
Owner Maintenance
8-47íSome models.
MX-5_8X49-EA-07F_Edition5 Page329
Thursday, February 21 2008 12:52 AM
Form No.8X49-EA-07F