2008 MAZDA MODEL MX-5 MIATA clock

Black plate (270,1)
To install the nut
1. Place the key on top of the nut, and besure to hold the key square to it. If you
hold the key at an angle, you may
damage both key and nut. Don't use a
power impact wrench.
2. Place the lug wrench on top of the key, apply pressure, and turn it clockwise.
qMounting the Tire
1. Remove dirt and grime from the
mounting surfaces of the wheel and
hub, including the hub bolts, with a
cloth.
WARNING
Make sure the mounting surfaces of
the wheel, hub and lug nuts are clean
before changing or replacing tires: When changing or replacing a tire,
not removing dirt and grime from the
mounting surfaces of the wheel, hub
and hub bolts is dangerous. The lug
nuts could loosen while driving and
cause the tire to come off, resulting in
an accident.
2. Mount the tire. 3. Install the lug nuts with the beveled
edge inward; tighten them by hand.
WARNING
Do not apply oil or grease to lug nuts
and bolts and do not tighten the lug
nuts beyond the recommended
tightening torque: Applying oil or grease to lug nuts and
bolts is dangerous. The lug nuts
could loosen while driving and cause
the tire to come off, resulting in an
accident. In addition, lug nuts and
bolts could be damaged if tightened
more than necessary.
4. Turn the jack handle counterclockwise and lower the vehicle. Use the lug
wrench to tighten the nuts in the order
shown.
7-16
In Case of an Emergency
Flat Tire
MX-5_8X49-EA-07F_Edition5 Page270
Thursday, February 21 2008 12:51 AM
Form No.8X49-EA-07F

Black plate (321,1)
(Halogen bulb)
NOTE
Replacing low-beam halogen bulbs is difficult
therefore contacting an Authorized Mazda
Dealer is recommended.
1. If you are changing the right headlightbulb, start the engine, turn the steering
wheel all the way to the left, and turn
off the engine. If you are changing the
left headlight bulb, turn the steering
wheel to the right.
2. Turn the screws counterclockwise and remove them.
3. Turn the center section of the plasticretainers counterclockwise and remove
them, then remove the mudguard.
Removal
Installation
4. Disconnect the electrical connector from the bulb by pulling it to the rear.
5. Pull off the sealing cover.
6. Unhook the bulb retaining spring.
7. Swing the retaining spring out and
away to free the headlight bulb.
8. Carefully remove the socket and bulb assembly by pulling it straight back.
Maintenance and Care
Owner Maintenance
8-39
MX-5_8X49-EA-07F_Edition5 Page321
Thursday, February 21 2008 12:52 AM
Form No.8X49-EA-07F

Black plate (322,1)
9. Remove the headlight bulb from thesocket.
10. Install the new socket and bulb
assembly in the reverse order of
removal.
NOTE
lIf the halogen bulb is accidentally touched,
it should be cleaned with rubbing alcohol
before being used.
lUse the protective cover and carton for the
replacement bulb to dispose of the old bulb
promptly and out of the reach of children.
lWhen reinstalling the sealing cover, make
sure
faces up.
Front fog light bulbsí
1. If you are changing the right Front fog light bulb, start the engine, turn the
steering wheel all the way to the left,
and turn off the engine. If you are
changing the left Front fog light bulb,
turn the steering wheel to the right. 2. Turn the screws counterclockwise and
remove them.
3. Turn the center section of the plastic
retainers counterclockwise and remove
them, then remove the mudguard.
Removal
Installation
4. Turn the socket and bulb assembly counterclockwise, and carefully pull it
backward.
8-40
Maintenance and Care
íSome models.
Owner Maintenance
MX-5_8X49-EA-07F_Edition5 Page322
Thursday, February 21 2008 12:52 AM
Form No.8X49-EA-07F

Black plate (323,1)
5. Disconnect the socket and bulbassembly from the electrical connector
by pressing the tab on the connector
with your finger and pulling it.
6. Install the new socket and bulbassembly in the reverse order of
removal.
NOTE
lIf the halogen bulb is accidentally touched,
it should be cleaned with rubbing alcohol
before being used.
lUse the protective cover and carton of the
replacement bulb to dispose of the old bulb
promptly out of the reach of children.
Front turn signal lights
1. If you are changing the right front turn signal light bulb, start the engine, turn
the steering wheel all the way to the
left, and turn off the engine. If you are
changing the left front turn signal light
bulb, turn the steering wheel to the
right. 2. Turn the screws counterclockwise and
remove them.
3. Turn the center section of the plastic
retainers counterclockwise and remove
them, then remove the mudguard.
Removal
Installation
4. Turn the socket and bulb assembly counterclockwise and remove it.
Maintenance and Care
Owner Maintenance
8-41
MX-5_8X49-EA-07F_Edition5 Page323
Thursday, February 21 2008 12:52 AM
Form No.8X49-EA-07F

Black plate (324,1)
5. Disconnect the bulb from the socket.
6. Install the new bulb in the reverse orderof removal.
Parking lights
1. Turn the socket and bulb assemblycounterclockwise and remove it.
2. Disconnect the bulb from the socket.
3. Install the new bulb in the reverse order of removal.
Front side-marker lights
NOTE
To replace the bulb, contact an Authorized
Mazda Dealer.
1. Slide the unit as shown in the figure toremove it.
2. Turn the socket and bulb assembly
counterclockwise and remove it.
3. Disconnect the bulb from the socket.
4. Install the new bulb in the reverse order of removal.
8-42
Maintenance and Care
Owner Maintenance
MX-5_8X49-EA-07F_Edition5 Page324
Thursday, February 21 2008 12:52 AM
Form No.8X49-EA-07F

Black plate (325,1)
Brake lights/Taillights, Rear turn signal
lights, Reverse lights
1. Pull the center section of the plasticretainers and remove them, then
remove the trunk end trim.
Removal
Installation
2. On the side the bulb is to be replaced, pull the center section of the plastic
retainers and remove them, then
remove the trunk side trim.
Removal
Installation
3. Turn the socket and bulb assembly counterclockwise and remove it. 4. Disconnect the bulb from the socket.
Brake lights/Taillights
Rear turn signal lights
Reverse lights
5. Install the new bulb in the reverse order of removal.
High-mount brake light
Due to the complexity and difficulty of
the procedure, the LED bulbs should be
replaced by an Authorized Mazda Dealer.
License plate lights
Due to the complexity and difficulty of
the procedure, the bulbs should be
replaced by an Authorized Mazda Dealer.
Maintenance and Care
Owner Maintenance
8-43
MX-5_8X49-EA-07F_Edition5 Page325
Thursday, February 21 2008 12:52 AM
Form No.8X49-EA-07F