2008 MAZDA MODEL B-SERIES bulb

3. Install the electrical connector into the plastic base until it snaps,
locking it into position.
4. Turn the headlamps on and make sure they work properly. If the
headlamp was correctly aligned before you changed the bulb, you
should not need to align it again.
Replacing front park/turn side marker bulbs
1. Make sure headlamp switch is in
OFF position, then open the
hood.
2. Remove the screw from lamp
assembly.
3. Disengage lamp assembly by
pulling it straight forward. It has
a snap fit.
4. Rotate bulb socket
counterclockwise and remove
from lamp assembly.
5. Carefully pull bulb straight out
of socket and push in the new
bulb.
6. Install the bulb socket in lamp
assembly by turning clockwise.
7. Align the lamp on the vehicle
and push to snap in place.
8. Install the screw on lamp assembly.
2008 B-Series(mbs)
Owners Guide (post-2002-fmt)
USA(fus)
Lights
49

Replacing stop lamp/tail lamp/sidemarker lamp/turn lamp/backup
lamp bulbs
These bulbs are located in the same
portion of the tail lamp assembly,
one just below the other. Follow the
same steps to replace either bulb:
1. Open the tailgate to expose the
lamp assemblies.
2. Remove the four screws and the
lamp assembly from vehicle.
3. Rotate the bulb socket
counterclockwise and remove
from lamp assembly.
4. Carefully pull the bulb straight
out of the socket and push in
the new bulb.
5. Install the bulb socket in lamp
assembly by turning clockwise.
6. Install the lamp assembly and
secure with four screws.
2008 B-Series(mbs)
Owners Guide (post-2002-fmt)
USA(fus)
Lights
50

Replacing fog lamp bulbs
WARNING: Handling Halogen Bulbs: When a halogen bulb
breaks, it is dangerous. These bulbs contain pressurized gas. If
one is broken, it will explode and serious injuries could be
caused by the flying glass. If the glass portion of the bulb is
touched with bare hands, body oil could cause the bulb to
overheat and explode when lit. Never touch the glass portion of
the bulb with your bare hands and always wear eye protection
when handling or working around halogen bulbs.
WARNING: Children and Halogen Bulbs: Playing with a halogen
bulb is dangerous. Serious injuries could be caused by dropping
a halogen bulb or breaking in some other way. Always keep
halogen bulbs out of the reach of children.
NOTE: If the bulb is accidentally touched, it should be cleaned with
rubbing alcohol before being used.
1. Remove the bulb socket from
the fog lamp by turning
counterclockwise.
2. Disconnect the electrical
connector from the fog lamp
bulb.
3. Connect the electrical connector to the new fog lamp bulb.
4. Install the bulb socket in the fog lamp turning clockwise.
Replacing high-mount brake lamp
To remove the brake lamp assembly:
1. Remove the two screws and
lamp assembly from vehicle.
2. Remove the bulb socket from
lamp assembly by rotating it counterclockwise.
3. Carefully pull bulb straight out of socket and push in the new bulb.
To install the brake lamp assembly:
1. Install the bulb socket into the lamp assembly by rotating clockwise.
2. Install the lamp assembly on the vehicle and secure with two screws.
2008 B-Series(mbs)
Owners Guide (post-2002-fmt)
USA(fus)
Lights
51

Replacing license plate lamp bulbs
The license plate bulbs are located
behind the rear bumper. To change
the license plate lamp bulbs:
1. Reach behind the rear bumper
to locate the bulb socket.
2. Twist the socket
counterclockwise and remove.
3. Pull out the old bulb from
socket and push in the new
bulb.
4. Install the bulb socket in lamp assembly by turning it clockwise.
2008 B-Series(mbs)
Owners Guide (post-2002-fmt)
USA(fus)
Lights
52

WARNING: The flow of fuel through a fuel pump nozzle can
produce static electricity, which can cause a fire if fuel is
pumped into an ungrounded fuel container.
Use the following guidelines to avoid electrostatic charge build-up when
filling an ungrounded fuel container:
•Place approved fuel container on
the ground.
•DO NOT fill a fuel container while
it is in the vehicle (including the
cargo area/pickup bed).
•Keep the fuel pump nozzle in contact with the fuel container while
filling.
•DO NOT use a device that would hold the fuel pump handle in the fill
position.
Fuel Filler Cap
Your fuel tank filler cap has an indexed design with a 1/4 turn on/off
feature.
When fueling your vehicle:
1. Turn the engine off.
2. Carefully turn the filler cap counterclockwise 1/4 of a turn to remove
it.
3. Pull to remove the cap from the fuel filler pipe.
4. To install the cap, align the tabs on the cap with the notches on the
filler pipe.
5. Turn the filler cap clockwise 1/4 of a turn until it clicks at least once.
The
comes on when the ignition is turned to the ON position to
ensure your bulb is working. When this light turns on, check the fuel
filler cap. Continuing to operate the vehicle with
on, can activate
the
indicator. When the fuel filler cap is properly re-installed, the
light(s) will turn off after one or two driving cycles with the fuel filler
cap properly installed. A driving cycle consists of a cold engine start-up
followed by mixed city/highway driving.It may take a long period of
time for the system to detect an improperly installed fuel filler
cap.
2008 B-Series(mbs)
Owners Guide (post-2002-fmt)
USA(fus)
Maintenance and Specifications
242

Readiness for Inspection/Maintenance (I/M) testing
Some state/provincial and local governments may have
Inspection/Maintenance (I/M) programs to inspect the emission control
equipment on your vehicle. Failure to pass this inspection could prevent
you from getting a vehicle registration. Your vehicle may not pass the I/M
test if the
indicator is on or not working properly (bulb is burned
out), or if the OBD-II system has determined that some of the emission
control systems have not been properly checked. In this case, the vehicle
is considered not ready for I/M testing.
If the
indicator is on or the bulb does not work, the vehicle may
need to be serviced. Refer to the On board diagnostics (OBD-II)
description in this chapter.
If the vehicle’s engine or transmission has just been serviced, or the
battery has recently run down or been replaced, the OBD-II system may
indicate that the vehicle is not ready for I/M testing. To determine if the
vehicle is ready for I/M testing, turn the ignition key to the ON position
for 15 seconds without cranking the engine. If the
indicator blinks
eight times, it means that the vehicle is not ready for I/M testing; if
the
indicator stays on solid, it means that the vehicle is ready for
I/M testing.
The OBD-II system is designed to check the emission control system
during normal driving. A complete check may take several days. If the
vehicle is not ready for I/M testing, the following driving cycle consisting
of mixed city and highway driving may be performed:
15 minutes of steady driving on an expressway/highway followed by 20
minutes of stop-and-go driving with at least four 30-second idle periods.
Allow the vehicle to sit for at least eight hours without starting the
engine. Then, start the engine and complete the above driving cycle. The
engine must warm up to its normal operating temperature. Once started,
do not turn off the engine until the above driving cycle is complete. If
the vehicle is still not ready for I/M testing, the above driving cycle will
have to be repeated.
2008 B-Series(mbs)
Owners Guide (post-2002-fmt)
USA(fus)
Maintenance and Specifications
250

A
ABS (see Brakes) .....................151
Air cleaner filter ...............257, 259
Airbag supplemental restraint
system ..........................................86
and child safety seats ..............89
description ................................86
disposal ......................................91
driver airbag ........................86, 89
indicator light ...........................90
operation .............................86, 89
passenger airbag .................86, 89
Ambulance packages ....................7
Antifreeze
(see Engine coolant) ................234
Anti-lock brake system
(see Brakes) ......................151–152
Anti-theft system ........................66
Audio system
(see Radio) ......................19, 21, 27
Automatic transmission ............156
driving an automatic
overdrive .................................157
fluid, specification ..................259
Auxiliary input jack (Line in) ....32
Auxiliary power point .................54
Axle
lubricant specifications ..........259
traction lok ..............................155
B
Battery .......................................232
acid, treating emergencies .....232
jumping a disabled battery ....189
maintenance-free ....................232
servicing ..................................232Belt-Minder...............................82
Booster seats ...............................95
Brakes ........................................151
anti-lock ...........................151–152
anti-lock brake system (ABS)
warning light ...........................153
fluid, checking and adding ....252
fluid, specifications .................259
lubricant specifications ..........259
parking ....................................153
shift interlock ..........................156
Break-in period .............................5
Bulbs ............................................46
C
Cargo cage ...................................60
Cell phone warning ...................267
Changing a tire .........................179
Child safety restraints ................95
child seat belts .........................95
Child safety seats ........................99
attaching with tether straps ..102
in front seat ............................100
in rear seat ..............................100
tether anchorage hardware ...102
Child safety seats - booster
seats .............................................95
Chimes (warning) .......................17
Cleaning your vehicle
engine compartment ..............207
instrument panel ....................210
interior .....................................210
Mazda car care products .......211
plastic parts ............................209
washing ....................................206
waxing .....................................206
wheels ......................................207
2008 B-Series(mbs)
Owners Guide (post-2002-fmt)
USA(fus)
Index
268

octane rating ...................243, 263
quality ......................................244
running out of fuel .................244
safety information relating to
automotive fuels .....................240
Fuel pump shut-off switch .......168
Fuses ..................................169–170
G
Gas cap (see Fuel cap) ............242
Gas mileage
(see Fuel economy) .................245
Gauges .........................................17
H
Hazard flashers .........................168
Headlamps ...................................42
aiming ........................................44
bulb specifications ....................46
daytime running lights .............43
flash to pass ..............................43
high beam .................................42
replacing bulbs .........................47
turning on and off ....................42
Heating
heating and air conditioning
system .................................39–40
Hood ..........................................221
I
Ignition ...............................146, 263
Infant seats (see Safety seats) ..99
Inspection/maintenance (I/M)
testing ........................................250
Instrument panel
cleaning ...................................210cluster ........................................12
lighting up panel and
interior .......................................43
location of components ............12
J
Jack ............................................179
positioning ...............................179
storage .....................179, 182–183
Jump-starting your vehicle ......189
K
Keys .......................................62, 67
positions of the ignition .........146
L
Lamps
bulb replacement
specifications chart ..................46
daytime running light ...............43
fog lamps ...................................42
headlamps .................................42
headlamps, flash to pass ..........43
instrument panel, dimming .....43
interior lamps .....................46–47
replacing bulbs .........................47
Lane change indicator
(see Turn signal) ........................45
Lights, warning and indicator ....12
anti-lock brakes (ABS) ..........153
Load limits .................................129
Loading instructions .................135
Locks
doors ..........................................62
Lubricant specifications ...........259
Lug nuts ....................................187
M
Manual transmission .................159
2008 B-Series(mbs)
Owners Guide (post-2002-fmt)
USA(fus)
Index
270