2008 Lancia Delta ESP

CARE AND MAINTENANCE203
5
REGULAR INSPECTIONS
Every 1,000 km or before long journeys, check and top
up if required:
engine coolant fluid level;
brake fluid level;
windscreen washer fluid level;
tyre pressure and condition;
operation of lights (headlights, direction indicators,
hazard lights, etc.);
operation of the windscreen wiper/washer system, po-
sition and wear of windscreen/rearscreen wiper blades;
Every 3,000 km check the following and top-up, if re-
quired: engine oil level.
You are recommended to use FL Selenia products, de-
signed and produced specifically for Lancia cars (see table
“Capacities” in chapter “6”).
DEMANDING USE OF THE CAR
If you use the vehicle mainly under one of the following
especially heavy conditions:
trailer or caravan towing;
dusty roads;
repetitive short distances (less than 7-8 km) with ex-
ternal temperatures below zero;
frequently idling the engine or long distances at low
speed driving (e.g. door-to-door deliveries) or long term
inactivity;
urban routes;

208CARE AND MAINTENANCE
ENGINE OIL A-fig. 1-2-3
Check the oil level a few minutes (about 5) after the en-
gine has stopped, with the car parked on level ground. The
oil level should be between the MIN and MAX marks on
the dipstick. The range between the MIN and MAX lev-
els corresponds to approximately 1 litre of oil.
If the oil level is near or under the MIN line, add oil
through the filler to reach the MAX line.
The oil level should never exceed the MAX line.Engine oil consumption
The maximum engine oil consumption is usually 400
grams every 1000 km. When the car is new, the engine
needs to be run in, therefore the engine oil consumption
can only be considered stabilised after the first 5,000 -
6,000 km.
IMPORTANT The oil consumption depends on driving
style and the conditions under which the car is used.
IMPORTANT After adding or changing the oil, let the en-
gine turn over for a few seconds and wait a few minutes
after turning it off before you check the level.

TECHNICAL DATA227
6
CHASSIS MARKING fig. 3
This is printed on the passenger compartment floor pan-
el near the front right seat. Move flap A forwards to ac-
cess it.
The chassis marking includes:
vehicle type (ZAR 844000);
chassis manufacturing serial number.BODYWORK PAINT IDENTIFICATION PLATE
fig. 4
This plate is applied inside the bonnet and shows the fol-
lowing data:
A Paint manufacturer.
B Colour name.
C Lancia colour code.
D Respray and touch up code.
ENGINE MARKING
The engine marking is stamped on the cylinder block and
includes the model and the chassis number.
fig. 3L0E0118mfig. 4L0E0119m

198A1000
Otto
4 in line
72 x 84
1368
9,8
± 0,2
110
150
5500
206 (*)
21
2250/3000 (*)
NGK IKR9F8
Unleaded petrol
95 RON (Specification EN228)
198A4000
Otto
4 in line
72 x 84
1368
9,8
± 0,2
88
120
5000
206
21
1750
NGK IKR9F8
Unleaded petrol
95 RON (Specification EN228)
TECHNICAL DATA229
6
ENGINE
INTRODUCTION 1.4 Turbo Jet 120 HP 1.4 Turbo Jet 150 HP
Engine code
Cycle
Number and layout of cylinders
Piston bore and stroke mm
Total displacement cm3
Compression ratio
Maximum power (EEC) kW
HP
corresponding ratio rpm
Maximum torque (EEC) Nm
kgm
corresponding ratio rpm
Spark plugs
Fuel
(*) With SPORT function activated (where required)

844A1000
Diesel
4 in line
82 x 90.4
1910
16.5
± 0.4
139,5
190
4000
400
41
2000
Diesel fuel for
motor vehicles
(Specification EN590)
198A5000
844A2000 ()
Diesel
4 in line
83 x 90.4
1956
16.5
± 0.4
121,3/120 (
)
165/163 ()
4000
360
36.7
1750
Diesel fuel for
motor vehicles
(Specification EN590)
230TECHNICAL DATA
198A2000
955A4000 ()
Diesel
4 in line
79.5 x 80.5
1598
16.5
± 0.4
88/85 (
)
120/115 ()
4000
300
31
1500
Diesel fuel for
motor vehicles
(Specification EN590)
() For versions/markets where applicable
INTRODUCTION 1.6 Multijet 1.9 Twin Turbo Multijet 2.0 Multijet
Engine code
Cycle
Number and layout of cylinders
Piston bore and stroke mm
Total displacement cm3
Compression ratio
Maximum power (EEC) kW
HP
corresponding ratio rpm
Maximum torque (EEC) Nm
kgm
corresponding ratio rpm
Fuel

234TECHNICAL DATA
WHEELS
RIMS AND TYRES
Pressed steel or alloy rims. Tubeless radial carcass tyres.
All approved tyres are listed in the Log Book.
IMPORTANT In the event of discrepancies between the
information provided on this “Owner’s handbook” and
the “Log book”, consider the specifications shown in the
log book only.
Respect the prescribed size to ensure safety of the car in
movement. Fit tyres of the same make and type on all
wheels.
IMPORTANT Do not use inner tubes with Tubeless tyres.
SMALL SPARE WHEEL
Pressed steel rim Tubeless tyre.
WHEEL GEOMETRY
Front wheel toe-in: –1
±1 mm
Rear wheel toe-in: 2
± 2 mm
The values refer to the car in running order.READING TYRE MARKINGS fig. 5
Example: 195/55 R 16 91 V
195 = Nominal width (S, distance in mm between
sidewalls).
55 = Height/width ratio (H/S) in percentage.
R = Radial tyre.
16 = Rim diameter in inches (Ø).
91 = Load rating (capacity).
V = Maximum speed rating.
fig. 5L0E0120m

TECHNICAL DATA235
6
Load rating (capacity)
60 = 250 kg 84 = 500 kg
61 = 257 kg 85 = 515 kg
62 = 265 kg 86 = 530 kg
63 = 272 kg 87 = 545 kg
64 = 280 kg 88 = 560 kg
65 = 290 kg 89 = 580 kg
66 = 300 kg 90 = 600 kg
67 = 307 kg 91 = 615 kg
68 = 315 kg 92 = 630 kg
69 = 325 kg 93 = 650 kg
70 = 335 kg 94 = 670 kg
71 = 345 kg 95 = 690 kg
72 = 355 kg 96 = 710 kg
73 = 365 kg 97 = 730 kg
74 = 375 kg 98 = 750 kg
75 = 387 kg 99 = 775 kg
76 = 400 kg 100 = 800 kg
77 = 412 kg 101 = 825 kg
78 = 425 kg 102 = 850 kg
79 = 437 kg 103 = 875 kg
80 = 450 kg 104 = 900 kg
81 = 462 kg 105 = 925 kg
82 = 475 kg 106 = 950 kg
83 = 487 kgMaximum speed rating
Q = up to 160 km/h. H = up to 210 km/h.
R = up to 170 km/h. V = up to 240 km/h.
S = up to 180 km/h. W= up to 270 km/h.
T = up to 190 km/h. Y = up to 300 km/h.
U = up to 200 km/h.
Maximum speed rating
for snow tyres
QM + S = up to 160 km/h.
TM + S = up to 190 km/h.
HM + S = up to 210 km/h.
READING RIM MARKINGS fig. 5
Example: 6J x 15 H2 ET 31.5
6 = rim width in inches (1).
J = rim drop centre outline (side projection where the
tyre bead rests) (2).
15 = rim nominal diameter in inches (corresponds to di-
ameter of the tyre to be mounted) (3 = Ø).
H2 = shape and number of the humps (circumference re-
lief, holding into its seat the bead of the Tubeless
tyre on the rim).
ET 31.5 = wheel camber angle (distance between the
disc/rim supporting plane and the wheel rim cen-
tre line).

1410
570
1077
903
1980
1300
80
601320
570
1002
888
1890
1300
80
60
240TECHNICAL DATA
WEIGHTS
Weights (kg) 1.4 Turbo Jet 1.6 Multijet
Unladen weight (with all fluids, fuel tank filled to
90% and without optional equipment)
Carrying capacity (*) including the driver:
Maximum permitted loads (**)
– front axle:
– rear axle:
– total:
Towable loads
Maximum load on roof
Maximum load on tow hitch
(trailer with brakes):
(*) If special equipment is fitted (sunroof, tow hitch, etc.) the unladen car weight increases, thus reducing the specified carrying
capacity.
(**) Loads must not be exceeded. The driver is responsible for arranging the loads in the boot and/or on the roof so that they com-
ply with these limits.