2008 Lancia Delta tow

88GETTING TO KNOW YOUR CAR
Electric window system initialisation
The safety system must be re-initialised after disconnect-
ing the battery or if the relevant protection fuse is blown.
Initialisation procedure:
fully close the window to be initialised manually;
after the window has reached the upper end of travel,
hold the up button pressed for at least one second.
IMPORTANT Where provided, following the disconnec-
tion of the power supply (replacing or disconnecting the
battery or replacing the protection fuse for the electric win-
dows control units), the automatic setting for the electric
windows must be reset.The reset operation should be carried out with the doors
closed according to the following procedure:
1. completely lower the driver-side window and keep the
button pressed for at least 3 seconds once the end of
travel position has been reached;
2. completely raise the driver-side window and keep the
button pressed for at least 3 seconds once the end of
travel position has been reached;
3. repeat stages 1 and 2 for the passenger-side window
4. check that the initialisation has taken place correctly
by checking the automatic operation of the windows.
IMPORTANT With central locking on, operating the in-
ternal handle of one of the doors will unlock all the doors.
If there is no power (blown fuse, battery disconnected,
etc.) the doors can still be locked manually. As in this case
the automatic window opening function is not available,
to open or close the door with the window closed, apply
pressure to the window towards the vehicle interior, to aid
the passage of the window against the trim.

94GETTING TO KNOW YOUR CAR
fig. 62L0E0220m
DOUBLE LOAD COMPARTMENT
(MAGIC BACK BOX) (where applicable)
In addition to reclining seats the car can also be equipped
with an adjustable load platform with two different heights
in order to even the load and adjust the luggage com-
partment capacity.
Keeping the load platform in the upper position makes it
possible for the space created underneath to be used as
another compartment that can be used to store more frag-
ile or smaller objects.
To access the compartment under the load compartment,
lift up shelf A holding it with your hands and put the de-
sired objects inside.
IMPORTANT Movements of the load platform may take
place if it is in a central position in relation to the lugga-
ge compartment.To place shelf A at the level of the floor
(fully lowered) fig. 63:
always turn the elements C - Fig. 62 so that they are
always turn the elements C - Fig. 62 so that they are
in a vertical position against the seat backrest;
grip the handle B and lift up shelf A by around 45°
(point 1);
pull the shelf in a horizontal direction towards itself
until the end of travel position (point 2);
push the shelf downwards gently until point 3 is rea-
ched (fully lowered);
accompany the shelf to the “fully lowered” position
(point 4).
To move shelf A from the fully lowered position to
the highest position Fig. 64:
pull handle B from point 1 and raise shelf A by around
45°;
pull the shelf upwards to point 2 and leave it resting
on the side supports D;
pull the shelf towards itself as far as point 3 (fully
forwards);
let the shelf fall at point 4 in the "fully raised" position.
To extract the spare wheel:
pull the load shelf upwards using handle B;
lift up the load compartment carpet;
extract the tape and hook for the carpet and attach it
to the boot upper seal.

GETTING TO KNOW YOUR CAR119
1
Detection distances
Central operating range 140 cm
Side operating range 60 cm
If several obstacles are detected by the sensors, only the
nearest one is considered.
FAILURE INDICATIONS
Any faults in the parking sensor system are indicated,
when reverse gear is engaged, by the
èwarning light on
the instrument panel lighting up and a dedicated message
appearing on the multifunctional display.
OPERATION WITH TRAILER
Parking sensor operation is deactivated automatically
when the trailer electric cable plug is fitted into the car
tow hook socket.
The sensors are automatically reactivated when the trail-
er cable plug is disconnected.
The sensor must be clean of mud, dirt, snow
or ice in order for the system to work. Be
careful not to scratch or damage the sensors
while cleaning them. Avoid using dry, rough or hard
cloths. Clean the sensors with clean water with the
addition of car shampoo if necessary. In washing
stations, clean the sensors quickly, keeping the
steam jet/high pressure washing nozzles at least 10
cm away from the sensors.
GENERAL WARNINGS
During parking manoeuvres, pay the utmost attention
to any obstacles that could be located above or below
the sensors.
Under certain circumstances objects located close to
the car are not detected and could therefore cause dam-
age to the car or be damaged themselves.
The following conditions may influence the performance
of the parking sensor system:
reduced sensor sensitivity and reduced parking aid sys-
tem performance could be caused by the presence of
the following on the sensor: ice, snow, mud, multiple
layers of paint

SAFETY127
2
The rear seat belts must be used as shown in the diagram
in fig. 2.
IMPORTANT After putting the seats back in their travel
position, restore the seat belt position to make them ready
for use.
IMPORTANT If the rear seat is being moved and this cau-
ses the middle seat belt to lock temporarily, normal con-
ditions can be restored by simply moving the seat towards
the back of the car.
fig. 2L0E0062m
S.B.R. SYSTEM
The car is provided with the S.B.R. (Seat Belt Reminder)
system, which warns the driver and the front passenger
if the seat belt is not buckled, as follows:
warning light
tinuously for the first 6 seconds;
warning light
mittently for the next 96 seconds.
To deactivate the system permanently, contact a Lancia
Dealership.
The S.B.R. system be reactivated using the set-up menu.

STARTING UP AND DRIVING147
3
Starting the engine .......................................................................... 148
Handbrake ...................................................................................... 150
Using the manual gearbox ............................................................... 151
Reducing running costs..................................................................... 152
Towing trailers ................................................................................. 154
Snow tyres ....................................................................................... 155
Snow chains .................................................................................... 156
Storing the car ................................................................................. 156

150STARTING UP AND DRIVING
Never jump start the engine by pushing, tow-
ing or driving downhill. This could cause a
flow of fuel into the catalytic converter and
damage it beyond repair.
HOW TO WARM UP THE ENGINE AFTER
IT HAS JUST STARTED
Proceed as follows:
drive off slowly, letting the engine turn at medium
speed. Do not accelerate abruptly;
do not demand maximum performance for the first few
kilometres. Wait until the engine coolant gauge starts
moving.
STOPPING THE ENGINE
Turn the ignition key to STOP while the engine is idling.
IMPORTANT After a taxing drive, you should allow the
engine to “catch its breath” before turning it off by letting
it idle to allow the temperature in the engine compartment
to fall.
A quick burst on the accelerator before turn-
ing off the engine serves absolutely no prac-
tical purpose, it wastes fuel and is damaging
especially to turbocharged engines.
HANDBRAKE
The handbrake lever is located between the two front seats.
Pull the lever upwards to operate the handbrake.
The car should be braked after a few snaps
of the lever, if it is not, contact a Lancia Deal-
ership to have it adjusted.
When the handbrake lever is engaged and the ignition key
is on MAR, the instrument panel warning light xwill
light.
Proceed as follows to release the handbrake:
slightly lift the handbrake and press release button
A-fig. 1;
hold button A pressed and lower the lever. The x
warning light on the instrument panel will go out.
Press the brake pedal when carrying out this operation
to prevent the car from moving accidentally.

152STARTING UP AND DRIVING
To engage reverse gear R from neutral, raise ring A un-
der the knob and at the same time move the gearshift lever
to the left and then forwards.
For the 1.6 Multijet version: To engage reverse R from neu-
tral, raise ring A under the knob and at the same time
move the gearshift lever to the right and then backwards.
IMPORTANT The clutch pedal should only be used to
change gear. Do not drive with you foot resting on the
clutch pedal, even lightly. For versions / markets where
provided, the electronic clutch control could cut in by in-
terpreting the anomalous driving style as a fault.
Press the clutch pedal fully to change gears
correctly. For this reason, there must be no
obstacles on the floor under the pedals: en-
sure that rubber mats (if any) are correctly posi-
tioned, not interfering with the pedals.
Do not drive with your hand resting on the
gear lever, because this pressure, even if light,
over time can wear out the gearbox inner
components.
REDUCING RUNNING COSTS
Here are some useful tips to save fuel and minimize pol-
luting emissions of CO
2and other pollutants (nitric oxide,
unburnt hydrocarbons, fine dusts etc…).
GENERAL CONSIDERATIONS
Car maintenance
Have checks and adjustments carried out in accordance
with the “Scheduled Service Plan”.
Tyres
Check tyre pressure regularly, at least once every four
weeks: excessively low pressure will increase fuel con-
sumption because rolling resistance will be higher.
Unnecessary loads
Do not travel with an overloaded boot. Do not travel with
too much luggage stowed in the boot. The weight of the
car (especially when driving in town) and its trim great-
ly affect fuel consumption and stability.

154STARTING UP AND DRIVING
Acceleration
Sudden acceleration has a very negative effect on fuel con-
sumption and emissions: accelerate gradually.
CONDITIONS OF USE
Cold starting
Short distances and frequent cold start-ups will prevent
the engine from reaching optimal running temperature.
Consequently, both fuel consumption (from +15 to +30%
on urban cycle ) and emissions will increase.
Traffic and road conditions
Rather high fuel consumption is caused by heavy traffic,
for instance when travelling in a queue with frequent use
of low gears or in cities with many traffic lights. Moun-
tain and rough roads also have a negative effect on fuel
consumption.
Traffic hold-ups
During prolonged hold-ups (level crossings) the engine
should be switched off.TOWING TRAILERS
IMPORTANT NOTES
The car must be provided with a type-approved tow hitch
and adequate electrical system to tow caravans or trail-
ers. Installation must be performed by specialised per-
sonnel who will issue the required papers for travelling on
roads.
Install any specific and/or additional rear-view mirrors as
specified by the Highway Code.
Remember that when towing a trailer, steep hills are hard-
er to climb, braking distances increase and overtaking
takes longer depending on the overall weight of the trail-
er.
Engage a low gear when driving downhill, rather than con-
stantly using the brake.
The weight of the trailer on the car’s tow hitch will reduce
the loading capacity of the car by the same amount. Con-
sider the weight of the vehicle at full load, including ac-
cessories and luggage to make sure you do not exceed the
maximum towable weight (shown on the registration cer-
tificate).
Respect the speed limits specific for each country for ve-
hicles towing trailers. In all cases, the top speed must not
exceed 100 km/h.