2008 JEEP GRAND CHEROKEE automatic transmission

Autostick Operation
By placing the shift lever in the D (Drive) position the
lever can be moved from side to side. This allows the
driver to engage the AutoStick mode. Moving the shift
lever to the right (+) or the left (-) will engage the
Autostick mode. In normal driving mode (Boxed ªDº
displayed in the PRNDL), moving the shift lever to the
right (+) will engage the Autostick mode putting the
transmission in the currently engaged gear. Moving the
shift lever to the Left (-) will engage the Autostick mode
and downshift the transmission 1 gear. For example, the
transmission is in Normal Mode and is currently operat-
ing in 3rd gear, a boxed D is displayed in the PRNDL, a
push to the right will engage the Autostick mode in 3rd
and a Boxed 3 will be displayed in the PRNDL. A push to
the left (-) will engage Autostick mode and downshift to
2nd gear and a Boxed 2 will be displayed in the PRNDL.Once Autostick mode is engaged a move to the Right (+)
or left (-) will trigger a upshift (+) or trigger a downshift
(-).
NOTE:In the Autostick mode, the transmission will
only shift up and down when Left or Right (D-/D+) is
manually selected by the driver.
The transmission will not allow a downshift if the
downshift would result in a engine overspeed condition.
The transmission will always allow a upshift from 1st to
2nd gear, however 2nd - 3rd, 3rd - 4th, and 4th ± 5th
upshifts will not be allowed if the vehicle speed is to low
to maintain operation in the selected gear. The transmis-
sion will automatically downshift as the vehicle slows to
a stop.
STARTING AND OPERATING 251
5

When in the Autostick mode, as the engine RPM nears
the engine maximum speed, an ªUPSHIFTº message will
appear in the Electronic Vehicle Information Center
(EVIC) portion of your instrument cluster. This message
appears in order to alert the driver that the engine speed
is approaching it's maximum value and a upshift to the
next gear is required. In the event that the driver does not
upshift, the engine control system will automatically do it
for the driver. Refer to ªElectronic Vehicle Information
Centerº in Section 4 of this manual.
Shifting into or out of the Autostick mode can be done at
any time without taking your foot off the accelerator
pedal. When the driver wishes to engage Autostick,
simply move the shift lever to the Left or Right (D-/D+)
position while in D (Drive).
Hold the shift lever to the right for at least one second to
disengage Autostick. The transmission will now operate
automatically; shifting between the five available gears.Autostick General Information
²
You can start out in first or second gear. The system
will ignore attempts to upshift at too low of a vehicle
speed.
²The transmission will automatically downshift to first
gear when coming to a stop.
²Starting out in second gear is helpful in snowy or icy
conditions.
²Avoid using speed control when Autostick is engaged.
²The transmission will automatically shift up when
maximum engine speed is reached while Autostick is
engaged.
²Transmission shifting will be more noticeable when
Autostick is engaged.
252 STARTING AND OPERATING

Trailer Towing Weights (Maximum Trailer Weight Ratings)
The following chart provides the maximum trailer weight ratings towable for your given drivetrain.
Engine/
TransmissionGCWR (Gross Combined
Wt. Rating)Frontal Area Max. GTW (Gross
Trailer Wt.)Max. Tongue Wt.
(See Note 1)
6.1L Automatic 8,800 lbs (3 992 kg) 40 Sq. Ft. (3.72
square meters)3,500 lbs (1 587 kg) 350 lbs (159 kg)
Refer to local laws for maximum trailer towing speeds.
Note 1 ± The trailer tongue weight must be considered as
part of the combined weight of occupants and cargo, and
should never exceed the weight referenced on the Tire
and Loading Information placard. Refer to the ªTire±
Safety Informationº section in this manual.
Trailer and Tongue Weight
Always load a trailer with 60% to 65% of the weight in
the front of the trailer. This places 10% to 15% of the
Gross Trailer Weight (GTW) on the tow hitch of your
vehicle. Loads balanced over the wheels or heavier in the
rear can cause the trailer to swayseverelyside to side
which will cause loss of control of vehicle and trailer.
Failure to load trailers heavier in front is the cause of
many trailer accidents.
290 STARTING AND OPERATING

WARNING!
Do not connect trailer brakes to your vehicle's hy-
draulic brake lines. It can overload your brake sys-
tem and cause it to fail. You might not have brakes
when you need them and could have an accident.
Towing any trailer will increase your stopping dis-
tance. When towing you should allow for additional
space between your vehicle and the vehicle in front
of you. Failure to do so could result in an accident.
Towing Tips
Before setting out on a trip, practice turning, stopping
and backing the trailer in an area away from heavy
traffic.
Towing Tips Ð Automatic Transmission
The ªDº range can be selected when towing. However, if
frequent shifting occurs while in this range, the ª3º range
should be selected.
NOTE:Using the ª3º range while operating the vehicle
under heavy operating conditions will improve perfor-
mance and extend transmission life by reducing exces-
sive shifting and heat build up. This action will also
provide better engine braking.
The automatic transmission fluid and filter should be
changed if you REGULARLY tow a trailer for more than
45 minutes of continuous operation. See Schedule ªBº in
section 8 of this manual for transmission fluid change
intervals.
NOTE:Check the automatic transmission fluid level
before towing.
STARTING AND OPERATING 295
5

NPower Steering Fluid Check..............320
NBody Lubrication.....................321
NWindshield Wiper Blades................322
NWindshield Washers Ð Front And Rear.....322
NExhaust System......................323
NCooling System.......................324
NHoses And Vacuum/Vapor Harnesses.......329
NBrake System........................329
NBrake Fluid Level Check................331
NFuel System Hoses....................332
NAutomatic Transmission................333
NFront And Rear Wheel Bearings...........333NAppearance Care And Protection From
Corrosion...........................333
mFuse Panel...........................338
NInterior Fuses........................338
NUnderhood Fuses (Power Distribution
Center)............................341
NUnderhood Fuses (Integrated Power
Module)............................344
mVehicle Storage........................345
mReplacement Bulbs......................346
mBulb Replacement......................347
NHigh Intensity Discharge Headlights (HID) Ð
If Equipped.........................347
NHead Light..........................347
304 MAINTAINING YOUR VEHICLE

ONBOARD DIAGNOSTIC SYSTEM Ð OBD II
Your vehicle is equipped with a sophisticated onboard
diagnostic system called OBD II. This system monitors
the performance of the emissions, engine, and automatic
transmission control systems. When these systems are
operating properly, your vehicle will provide excellent
performance and fuel economy, as well as engine emis-
sions well within current government regulations.
If any of these systems require service, the OBD II system
will turn on the ªMalfunction Indicator Light.º It will
also store diagnostic codes and other information to
assist your service technician in making repairs. Al-
though your vehicle will usually be drivable and not
need towing, see your dealer for service as soon as
possible.CAUTION!
²Prolonged driving with the ªMalfunction Indica-
tor Lightº on could cause further damage to the
emission control system. It could also affect fuel
economy and driveability. The vehicle must be
serviced before any emissions tests can be per-
formed.
²If the ªMalfunction Indicator Lightº is flashing
while the engine is running, severe catalytic con-
verter damage and power loss will soon occur.
Immediate service is required.
MAINTAINING YOUR VEHICLE 307
7

NOTE:Use only manufacturer approved A/C System
Sealers, Stop Leak Products, Seal Conditioners, Compres-
sor Oil, or Refrigerants.
Refrigerant Recovery and Recycling
R-134a Air Conditioning Refrigerant is a hydrofluorocar-
bon (HFC) that is endorsed by the Environmental Pro-
tection Agency and is an ozone-saving product. How-
ever, the manufacturer recommends that air conditioning
service be performed by dealers or other service facilities
using recovery and recycling equipment.
Power Steering Fluid Check
The power steering system requires the use of Mopart
Hydraulic System Power Steering Fluid (P/N
05142893AA), or equivalent, which meets
DaimlerChrysler Material Standard MS-10838.
CAUTION!
Do not use Automatic Transmission Fluid (ATF) or
other types of power steering fluids when servicing
the power steering system of this vehicle. Damage to
the power steering system can result from the use of
the wrong power steering fluid.
Checking the power steering fluid level at a defined
service interval is not required. The fluid should only be
checked if a leak is suspected, abnormal noises are
apparent, and/or the system is not functioning as antici-
pated. Coordinate inspection efforts through a certified
ªDaimlerChrysler Dealership.º
320 MAINTAINING YOUR VEHICLE

Automatic Transmission
Fluid Level Check
Regular automatic transmission fluid level checks are not
required. For this reason the dipstick is omitted.
If you notice fluid loss or gear shift malfunction, have
your authorized dealer check the transmission fluid level.
CAUTION!
The fluid level is preset at the factory and does not
require adjustment under normal operating condi-
tions. If a transmission fluid leak occurs, visit your
authorized dealer immediately. Severe damage to the
transmission may occur. Your authorized dealer has
the proper tools to accurately adjust the fluid level.
Front And Rear Wheel Bearings
Front and rear wheel bearings are permanently sealed.
No regular maintenance is required for these compo-
nents.
Appearance Care And Protection From Corrosion
Protection of Body and Paint from Corrosion
Vehicle body care requirements vary according to geo-
graphic locations and usage. Chemicals that make roads
passable in snow and ice, and those that are sprayed on
trees and road surfaces during other seasons, are highly
corrosive to the metal in your vehicle.
The following maintenance recommendations will enable
you to obtain maximum benefit from the corrosion
resistance built into your vehicle.
What Causes Corrosion?
Corrosion is the result of deterioration or removal of
paint and protective coatings from your vehicle.
MAINTAINING YOUR VEHICLE 333
7