2008 HUMMER H3 ignition

Sunroof
To operate a power sliding sunroof, the ignition must be
on, or Retained Accessory Power (RAP) must be active.
SeeRetained Accessory Power (RAP) on page 2-20.
The switch used to
operate the sunroof is
located in the headliner.
Open/Close:Press and release the back of the switch
to fully open the sunroof. If the sunshade is in the
closed position, it automatically opens with the sunroof.
To stop the sunroof before it reaches the full open
position press and release the front or back of the switch.
An air deector raises when the sunroof is fully opened.
Press the front of the switch to close the sunroof.Vent:With the sunroof closed, press and hold the front
of the switch to vent the sunroof. To stop the sunroof
before it reaches its full vent position, release the switch.
Press and hold the back of the switch to close.
Do not keep the sunroof open for long periods of time.
Debris may collect in the tracks.
Sunshade Operation
The sunshade automatically opens with the sunroof,
but can be manually pulled shut after the sunroof
is closed.
To adjust the sunshade, push it backward or pull it
forward to the desired position. The sunshade cannot
be adjusted further than the current closed position
of the sunroof.
2-60

Hazard Warning Flashers
The hazard warning ashers let you warn the police and
others that you have a problem. The front and rear
turn signal lamps will ash on and off.
The hazard warning
asher button is located
towards the center of
the instrument panel.
Press the button to make the front and rear turn signal
lamps ash on and off. Press the button again to
turn the ashers off.While the hazard warning ashers are on, the turn
signals do not work.
The hazard warning ashers work no matter what
position the key is in, and even if the key is not in the
ignition switch.
Other Warning Devices
If you carry reective triangles, you can set one up at
the side of the road about 300 feet (100 m) behind your
vehicle.
Horn
To sound the horn, press the horn symbol on the
steering wheel pad.
3-6

Reducing Speed While Using Cruise
Control

Press and hold the set button until you reach the
desired lower speed, then release it.
To slow down in very small amounts, briey press
the set button. Each time you do this, you will go
about 1 mph (1.6 km/h) slower.
Passing Another Vehicle While Using
Cruise Control
Use the accelerator pedal to increase your speed.
When you take your foot off the pedal, your vehicle
slows down to the cruise control speed you set earlier.
Using Cruise Control on Hills
How well your cruise control works on hills depends
upon your speed, load, and the steepness of the hills.
When going up steep hills, you might want to step on the
accelerator pedal to maintain the vehicle speed.When going downhill, you might have to brake or shift
to a lower gear to keep the vehicle speed down. Of
course, applying the brake turns off the cruise control.
Many drivers nd this to be too much trouble and do not
use cruise control on steep hills.
Ending Cruise Control
To turn off the cruise control, do one of the following:
Step lightly on the brake pedal.
Move the cruise control switch to off.
Lightly tap or press the clutch, if you have a manual
transmission.
Erasing Speed Memory
When you turn off the cruise control or the ignition, the
cruise control set speed memory is erased.
3-14

To disable automatic lighting, do any of the following:
Turn the headlamp control from AUTO to off
and release the control. It will return back to
the AUTO position by itself.
Turn the headlamp control from AUTO to the
parking lamp or headlamp position.
SeeAutomatic Headlamp System on page 3-17for
more information.
Vehicles rst sold in Canada with an automatic
transmission cannot turn off automatic headlamps
unless the gear position is in PARK (P) and the
headlamp switch is turned to the Off position. Vehicles
rst sold in Canada with a manual transmission can
turn off the automatic headlamps with the headlamp
control; however, the parking lamps will remain on.
;(Parking Lamps):Turn the knob to this position to
turn on the parking lamps, together with the following:
Sidemarker Lamps
Taillamps
License Plate Lamps
Instrument Panel Lights
2(Headlamps):Turn the knob to this position to turn
on the headlamps, together with the previously listed
lamps and lights.
The headlamps can be switched from low to high beam
by pushing the turn signal/multifunction lever toward
the instrument panel.
Headlamps on Reminder
A headlamp reminder chime will sound if the following
conditions are met:
The driver door is open.
Parking lamps or headlamps are manually
turned on.
The key is either not in the ignition switch, or it is in
the LOCK position of the ignition switch.
The headlamp reminder cannot be turned off if the
conditions listed above are met.
In the automatic mode, the headlamps turn off once the
ignition is in ACC.
3-16

Daytime Running Lamps (DRL)
Daytime Running Lamps (DRL) can make it easier for
others to see the front of your vehicle during the
day. DRL can be helpful in many different driving
conditions, but they can be especially helpful in the short
periods after dawn and before sunset. Fully functional
daytime running lamps are required on all vehicles
rst sold in Canada.
The DRL system will come on when the following
conditions are met:
The ignition is on.
The exterior lamps control is in AUTO.
The transmission is not in PARK (P) if you have an
automatic transmission.
The light sensor determines it is daytime.
When the DRL are on, no other lamps are on. The
instrument panel will not be lit up either. For vehicles rst
sold in Canada, if parking lamps are manually turned
on, DRL will stay on.
When it begins to get dark, the automatic headlamp
system will switch from DRL to the headlamps.
As with any vehicle, you should turn on the regular
headlamp system when you need it.
To turn off the DRL, seeExterior Lamps on page 3-15.Vehicles rst sold in Canada cannot turn off DRL unless
certain conditions are met. SeeExterior Lamps on
page 3-15.
Automatic Headlamp System
When it is dark enough outside, the automatic headlamp
system will turn on after the transmission has been
shifted from PARK (P) to DRIVE (D). The headlamps,
taillamps, sidemarker, parking lamps, roof marker lamps,
and the instrument panel lights will turn on at normal
brightness. The radio lights will become more dim when
the headlights are off compared to when the headlights
are on.
Your vehicle has a light sensor located on the top of the
instrument panel. Be sure it is not covered, or the
system will be on whenever the ignition is on.
The system may also turn on the headlamps when
driving through a parking garage, heavy overcast
weather, or a tunnel. This is normal.
There is a delay in the transition between the daytime
and nighttime operation of the Daytime Running
Lamps (DRL) and the automatic headlamp system so
that driving under bridges or bright overhead street lights
does not affect the system. The DRL and automatic
headlamp system will only be affected when the
light sensor detects a change in lighting lasting longer
than the delay.
3-17

If you start your vehicle in a dark garage, the automatic
headlamp system will come on immediately. Once
you leave the garage, it will take about one minute for
the automatic headlamp system to change to DRL if it is
light outside. During that delay, the instrument panel
cluster may not be as bright as usual. Make sure
the instrument panel brightness control is in the full
bright position. SeeInstrument Panel Brightness
on page 3-19.
Off-Road Lamps
The off-road lamps, if the vehicle has them, provide
auxiliary lighting when the vehicle is used off road.
These lamps are not intended to be used in place of
existing vehicle lighting. The lamps are not to be used
on any public street or highway and are to be covered
when not in use. Check your state and local laws before
installing or using any auxiliary lighting. In some
states it may be necessary to remove the roof lamps
when operating the vehicle on the highway.The switches for the off-road lamps are located in the
center of the instrument panel below the climate
controls. One switch is used for the front lower-grille
mounted off-road lamps, if the vehicle has them, and the
other switch is used for the roof-mounted off-road
lamps, if the vehicle has them.
To use the lamps, remove the covers from the lamps and
press the switch to turn them on or off. An indicator light
on the switch will turn on when the lamps are on.
Notice:Turning on the off-road lamps before
removing the lamp covers could damage the
off-road lamps and the covers. Always remove the
covers before turning on the off-road lamps.
The off-road lamps remain on even after the ignition is
turned off. The off-road lamp switch must be pressed
to turn them off.Roof Mounted Off-Road
Light Switch
Lower Grille Off-Road
Light Switch
3-18

Dome Lamp Override
E(Dome Lamp Override):You can use the dome
override button, located below the exterior lamps control,
to set the dome and footwell lamps to come on
automatically when a door is opened, or to remain off.
To turn the lamps off, press the button into the in
position. With the button in this position, the dome lamps
will remain off when the doors are open. To return the
lamps to automatic operation, press the button again
and return it to the out position. With the button in this
position, the dome lamps will come on when you
open a door.
Exit Lighting
With exit lighting, the interior lamps will come on when
you remove the key from the ignition. The lamps will not
come on if the dome override button is pressed in.
Reading Lamps
Your vehicle has reading lamps. Press the button
located next to the lamp to turn them on or off.
These lamps will not come on with the dome lamps.
Electric Power Management
The vehicle has Electric Power Management (EPM) that
estimates the battery’s temperature and state of
charge. It then adjusts the voltage for best performance
and extended life of the battery.
When the battery’s state of charge is low, the voltage is
raised slightly to quickly put the charge back in. When
the state of charge is high, the voltage is lowered slightly
to prevent overcharging. If the vehicle has a voltmeter
gage, you may see the voltage move up or down. This is
normal. If there is a problem, an alert will be displayed.
The battery can be discharged at idle if the electrical
loads are very high. This is true for all vehicles. This is
because the generator (alternator) may not be
spinning fast enough at idle to produce all the power
that is needed for very high electrical loads.
A high electrical load occurs when several of the
following loads are on: headlamps, high beams, fog
lamps, rear window defogger, climate control fan at
high speed, heated seats, engine cooling fans, trailer
loads, and loads plugged into accessory power outlets.
Battery Run-Down Protection
This feature shuts off the dome lamp if it is left on for
more than 20 minutes when the ignition is in LOCK. This
will help prevent your battery from running down.
3-20

\(Bi-Level):This mode directs air to the instrument
panel outlets, and the remaining air to the oor
outlets and the defroster and side window outlets.
Cooler air is directed to the upper outlets and warmer
air to the oor outlets.
[(Floor):This mode directs air to the oor outlets,
side window outlets, and defroster. Recirculation is
not available in this mode.
Defogging and Defrosting
Fog on the inside of windows is a result of high humidity
(moisture) condensing on the cool window glass. This
can be minimized if the climate control system is used
properly. There are two modes to clear fog or frost from
the windshield and side windows. Use the defog mode
to clear the windows of fog or moisture and warm the
passengers. Use the defrost mode to remove fog or frost
from the windshield more quickly. For best results, clear
all snow and ice from the windshield before defrosting.
/(Floor/Defog):This mode directs the air to the
windshield, the side window outlets, and to the
oor outlets. When this mode is selected, the system
runs the air conditioning system unless the outside
temperature is near freezing or below. Recirculation is
not available in this mode.
0(Defrost):This mode directs most of the air to the
windshield, and the side window outlets. When this
mode is selected, the system runs the air conditioning
system unless the outside temperature is near or below
freezing. Recirculation is not available in this mode.
Do not drive the vehicle until all the windows are clear.
Rear Window Defogger
The rear window defogger uses a warming grid to
remove fog or frost from the rear window when the key
is in the ignition and turned to ON/RUN.
=(Rear Defogger):Press the center of the right
knob on the control panel to turn the rear window
defogger on or off. First press of this button activates
the rear window defogger for 15 minutes and each
subsequent activation lasts seven and one-half minutes.
Notice:Do not use anything sharp on the inside of
the rear window. If you do, you could cut or damage
the warming grid, and the repairs would not be
covered by your warranty. Do not attach a temporary
vehicle license, tape, a decal or anything similar to
the defogger grid.
Outlet Adjustment
Use the air outlets located in the center and on the side
of your instrument panel to direct the airow.
Your vehicle has air outlets that allow you to adjust the
direction and amount of airow inside the vehicle.
3-24