2008 HUMMER H3 display

FLUID
This message displays if the brake uid is low. Check
the brake uid as soon as possible and have your
vehicle serviced by your dealer/retailer. SeeBrakes on
page 5-38for more information. Press and release
the reset stem to acknowledge the message and clear it
from the display.
FUEL CAP
This message displays if the vehicle’s fuel cap is either
off or loose. Pull over as soon as possible and check
to see if the fuel cap is secure. You may also see
the check engine light on the instrument panel cluster.
If the check engine light does come on when the
fuel cap was loose, it may take a few driving trips before
the light turns off. SeeMalfunction Indicator Lamp on
page 3-36for more information if the light still remains
on. Press and release the reset stem to acknowledge
the message and clear it from the display.
LOW FUEL
This message displays if the level of fuel in the vehicle
is low. Also check the fuel gage. SeeFuel Gage on
page 3-40for more information. Rell the fuel tank as
soon as possible.
LOW TIRE
This message displays if a low tire pressure is detected
in any of the vehicle’s tires. Press and release the reset
stem to acknowledge the message and clear it from the
display. The message appears at each ignition cycle until
the tires are inated to the correct ination pressure. See
Tires on page 5-54andInflation - Tire Pressure on
page 5-62for more information on tires and the correct
ination pressures.
OIL
This message displays when the oil pressure is low.
SeeOil Pressure Light on page 3-38andEngine Oil
on page 5-15for more information.
PARK BRK (Brake)
This message displays when the parking brake is set.
SeeParking Brake on page 2-32andBrake System
Warning Light on page 3-33for more information. The
message clears from the display after the parking brake
is released or by pressing and releasing the reset stem.
3-45

REDUCED POWER
This message displays when the vehicle’s engine power
is reduced. Reduced engine power can affect the
vehicle’s ability to accelerate. If this message is on, but
there is no reduction in performance, proceed to
your destination. The performance may be reduced the
next time the vehicle is driven. The vehicle may be
driven at a reduced speed while this message is on, but
acceleration and speed may be reduced. Anytime this
message stays on, the vehicle should be taken to
your dealer/retailer for service as soon as possible.
Press and release the reset stem to acknowledge the
message and clear it from the display.
SERV (Service) 4WD (Four-Wheel
Drive)
This message displays when there is a problem with the
transfer case control system. Check the transfer case
on your vehicle and have it serviced by your
dealer/retailer. SeeFull-Time Four-Wheel Drive on
page 2-27for more information about the transfer case.
Press and release the reset stem to acknowledge
the message and clear it from the display.
SERV (Service) TPM (Tire Pressure
Monitor)
This message displays if a part on the Tire Pressure
Monitor System (TPMS) is not working properly. The tire
pressure light also ashes and then remains on during
the same ignition cycle. SeeTire Pressure Light on
page 3-35. Several conditions may cause this message
to appear. SeeTire Pressure Monitor Operation on
page 5-65for more information. If the warning comes on
and stays on, there may be a problem with the TPMS.
See your dealer/retailer.
SERV (Service) VEH (Vehicle)
This message displays if your vehicle needs service.
Have your vehicle serviced by your dealer/retailer
as soon as possible.
3-46

SERVICE CHARG (Charge) SYS
(System)
This message displays if there is a problem with the
battery charging system. Under certain conditions, the
battery warning light may also turn on in the instrument
panel cluster. SeeCharging System Light on
page 3-32. The battery will not be charging at an
optimal rate and the vehicle will lose the ability to enter
the fuel economy mode. The vehicle is safe to drive,
however have the electrical system checked by
your dealer/retailer. Press and release the reset stem
to acknowledge the message and clear it from the
display.
SERVICE STAB (Stability) SYS
(System)
This message displays if there is a problem with the
StabiliTrak®system. Have your vehicle serviced by your
dealer/retailer. SeeStabiliTrak®System on page 4-7
for more information.
STAB (Stability) SYS (System) OFF
This message displays when the StabiliTrak®system is
turned off. SeeStabiliTrak®System on page 4-7for
more information.
TRAC (Traction) OFF
This message along with the traction off light displays
when the Traction Control System (TCS) is turned off by
pressing the TCS button. SeeTraction Off Light on
page 3-34andTraction Control System (TCS) on
page 4-5for more information.
TRACTION FAULT
This message displays if there is a problem with the
Traction Control System (TCS). Check the TCS as soon
as possible and have your vehicle serviced by your
dealer/retailer. SeeTraction Control System (TCS)
on page 4-5for more information. Press and release
the reset stem to acknowledge the message and clear it
from the display.
TURN SIGNAL
This message displays when the turn signal is on for
about 0.75 miles (1.2 km) of travel. Press and release
the reset stem to acknowledge the message and clear it
from the display.
3-47

Audio System(s)
Determine which radio your vehicle has and then read
the pages following to familiarize yourself with its
features.
{CAUTION:
This system provides you with far greater
access to audio stations and song listings.
Giving extended attention to entertainment
tasks while driving can cause a crash and you
or others can be injured or killed. Always keep
your eyes on the road and your mind on the
drive — avoid engaging in extended searching
while driving.
Keeping your mind on the drive is important for safe
driving. SeeDefensive Driving on page 4-2. Here
are some ways in which you can help avoid distraction
while driving.
While your vehicle is parked:
Familiarize yourself with all of its controls.
Familiarize yourself with its operation.
Set up your audio system by presetting your
favorite radio stations, setting the tone, and
adjusting the speakers. Then, when driving
conditions permit, you can tune to your favorite
radio stations using the presets and steering wheel
controls if the vehicle has them.
Notice:Before adding any sound equipment to
your vehicle, such as an audio system, CD player,
CB radio, mobile telephone, or two-way radio, make
sure that it can be added by checking with your
dealer/retailer. Also, check federal rules covering
mobile radio and telephone units. If sound
equipment can be added, it is very important to do
it properly. Added sound equipment may interfere
with the operation of your vehicle’s engine, radio,
or other systems, and even damage them. Your
vehicle’s systems may interfere with the operation
of sound equipment that has been added.
Your vehicle has a feature called Retained Accessory
Power (RAP). With RAP, the audio system can be
played even after the ignition is turned off. SeeRetained
Accessory Power (RAP) on page 2-20for more
information.
Setting the Time
Press and hold H until the correct hour and AM or PM
displays. Press and hold M until the correct minute
displays. The time can be set with the ignition on or off.
3-48

Playing the Radio
P
(Power/Volume):Press to turn the system on
and off.
Turn clockwise or counterclockwise to increase or to
decrease the volume.
DISP (Display):Press to switch the display between
the radio station frequency and the time. When the
ignition is turned off, press to display the time.
For XM™ (if equipped), press the DISP button while in
XM™ mode to retrieve four different categories of
information related to the current song or channel: Artist,
Song Title, Category or PTY (program type), Channel
Number/Channel Name.
To change the default on the display, press the DISP
button until you see the desired display, then hold
this knob for two seconds. The radio produces one beep
and the selected display becomes the default.
AUTO VOL (Automatic Volume):With automatic
volume, the audio system adjusts automatically to make
up for road and wind noise as you drive.
Set the volume at the desired level. Press to select
LOW, MEDIUM, or HIGH. Each higher setting allows for
more volume compensation at faster vehicle speeds.
Then as you drive, automatic volume increases
the volume, as necessary, to overcome noise at anyspeed. The volume level should always sound the same
to you as you drive. NONE displays if the radio cannot
determine the vehicle speed. To turn automatic
volume off, press until AVOL OFF displays.
Finding a Station
BAND:Press to switch between FM1, FM2, AM, or
XM1 or XM2 (if equipped). The selection displays.
e(Tune):Turn to select radio stations.
tSEEKu:Press and release the arrows to go to
the next or to the previous station and stay there.
To scan stations, press and hold either arrow for more
than two seconds. SCN or SCAN displays and the
radio produces one beep. The radio goes to a station,
plays for a few seconds, then goes to the next
station. Press either arrow again or one of the
pushbuttons to stop scanning presets.
To scan preset stations, press and hold either arrow for
more than four seconds. PSC or PSCN displays and
the radio produces two beeps. The radio goes to
a preset station, plays for a few seconds, then goes to
the next preset station. Press either arrow again or
one of the pushbuttons to stop scanning presets.
The radio only seeks and scans stations with a strong
signal that are in the selected band.
3-50

4(Information) (XM™ Satellite Radio Service):If the
current station has a message, the information symbol
displays. Press to see the message. The message can
display the artist, song title, call in phone numbers, etc.
If the entire message is not displayed, parts of the
message appears every three seconds. To scroll through
the message, press and release this button. A new group
of words display after every press of this button. Once the
complete message has displayed, the information symbol
disappears from the display until another new message is
received. The last message can be displayed by pressing
the
4button. You can view the last message until a new
message is received or a different station is tuned to.
When a message is not available from a station, NO
INFO displays.
1-6 (Preset Pushbuttons) (Radio with Six-Disc CD
Player):Press to play stations that are programmed on
the radio preset pushbuttons.
The radio only seeks preset stations with a strong signal
that are in the selected band.
Setting Preset Stations
Up to 30 stations (six FM1, six FM2, and six AM,
six XM1 and six XM2 (if equipped)), can be programmed
on the six numbered pushbuttons, by performing the
following steps:
1. Turn the radio on.
2. Press BAND to select FM1, FM2, AM, or
XM1 or XM2.
3. Tune in the desired station.
4. Press AUTO EQ to select the equalization.
5. Press and hold one of the six numbered
pushbuttons until a beep sounds. When that
numbered pushbutton is pressed, the station that
was set, returns and the equalization that was
selected, is stored for that pushbutton.
6. Repeat the steps for each pushbutton.
3-51

Setting the Tone (Bass/Treble)
e
(Bass/Treble):Press and release until BAS/BASS,
or TRE/TREB displays. Turn to increase or to
decrease. The display shows the bass or the treble
level. If a station is weak or has static, decrease
the treble.
To adjust the bass and the treble to the middle position,
press and hold this knob. The radio produces one beep.
To adjust all tone and speaker controls to the middle
position, press and hold when no tone or speaker control
is displayed. CEN or ALL CENTERED displays and a
beep sounds.
AUTO EQ (Automatic Equalization):Press to select
customized equalization settings designed for
country/western, jazz, talk, pop, rock, and classical.
To return the bass and treble to the manual mode, press
and release the
eknob until MANUAL displays.
For the Radio with Six-Disc CD Player, the equalization
one through seven options are included only if your
vehicle is equipped with the Bose
®system. Press the
AUTO EQ button to select equalization settings
designed for equalization one through seven.
To return the bass and treble to the manual mode, push
and release this knob until BASS and TREB displays.
Adjusting the Speakers (Balance/Fade)
e
(Balance/Fade):To adjust the balance between
the right and the left speakers, press and release until
BAL displays. Turn to move the sound toward the
right or the left speakers.
To adjust the fade between the front and the rear
speakers, press and release until FAD or FADE
displays. Turn to move the sound toward the front or the
rear speakers.
To adjust the balance and the fade to the middle
position, press this knob, then press it again and hold it
until one beep sounds.
To adjust all tone and speaker controls to the middle
position, press and hold when no tone or speaker control
is displayed. CEN or ALL CENTERED displays and a
beep sounds.
3-52

Finding a Category (CAT) Station
(XM™ Satellite Radio Service Only)
To select and nd a desired category perform the
following:
1. Press the CAT button to activate program type
select mode. A category displays.
2. Press the CAT button to select a category.
For the Radio with Six-Disc CD Player, turn the
eknob to select a category.
3. Once the desired category is displayed, press either
SEEK arrow to select and to take you to the
categories rst station.
4. To go to another station within that category and
the category is displayed, press the CAT button
once. If the category is not displayed, press the CAT
button twice to display the category and then to
go to another station.
For the Radio with Six-Disc CD Player, press
either SEEK arrow to go to another station within
that category and the category is displayed.
5. Press CAT to exit program type select mode.
If CAT times out and is no longer on the display, go
back to Step 1.If the radio cannot nd the desired program type, NONE
or NOT FOUND displays and the radio returns to the
last station you were listening to.
BAND (Alternate Frequency) (Radio with Single
CD):Alternate frequency allows the radio to switch
to a stronger station with the same category. To
turn alternate frequency on, press and hold BAND for
two seconds. AF ON displays. The radio can switch
to stations with a stronger frequency.
To turn alternate frequency off, press and hold BAND
again for two seconds. AF OFF displays. The radio does
not switch to other stations.
This function does not apply for XM™ Satellite Radio
Service.
Radio Messages
CAL ERR (Calibration Error):The audio system has
been calibrated for your vehicle from the factory. If
CAL ERR displays it means that the radio has not been
congured properly for your vehicle and it must be
returned to your dealer/retailer for service.
LOC (Locked):This message is displayed when the
THEFTLOCK
®system has locked up. Take your vehicle
to your dealer/retailer for service.
If any error occurs repeatedly or if an error cannot be
corrected, contact your dealer/retailer.
3-53