
Downloaded from www.Manualslib.com manuals search engine 199Electrical Accessories
SymptomsCausesSolutions
Image is blurred and distortedThe disc is copy protected
The player is compatible with the copy
system, so if the disc is copy protected, it
may not be able to play, and is not a problem
with the player
PBC function has no effect
when playing a VCD discThe disc contains no PBC functionUse discs that support the PBC function
Repeat function and album/
time search are unavailablePBC is set to onTurn off the PBC function
SymptomsCausesSolutions
Cannot play MP3
Disc is scratched or dirty Clean the disc with soft cloth
Laser head is dirtyClean the laser head with a laser head
cleaning disc
The disc is not supported by this playerPlease use discs supported by this player
The read side of the disc is inserted
upside-down
Insert the disc into the player with its label
side up
The sound is not smooth when
playing MP3
The disc is too dirty or scratchedClean or replace the disc
Partial content is damagedReplace the disc
Bad record conditionRe-record the disc
Name of MP3 file is not
displayed normallyIrregular file nameDo not use Chinese names
MP3 playing faults and solution

Downloaded from www.Manualslib.com manuals search engine GWFLORID Maintenance Manual218
detection but also during the diagnostic detection cycle. However, if a short circuit on the power supply causes
a malfunction, and the low-end transistor is opened while malfunctioned, the low-end transistor can only be
detected when starting up detection, as to avoid faulty execution.
(b) Ignition voltage is provided by a pressure increase converter.
(c) Acceleration sensor performs self-detection when starting up detection.
(d) Allowed offset range of the acceleration sensor during a diagnostic cycle.
(e) Microcontroller includes AD converter, ROM, RAM, etc.
(f) Security sensor status.
Caution: There is a short-circuiting bar inside the squib circuit connector. When the connector is not
connected, the short circuit happens between the squib circuit's terminal (+) and terminal (-), as to
avoid faulty deployment caused by static electricity. When the connector is bad and the short-circuiting
bar is connected, the fault symptom may not be eliminated.
4. Clear the trouble code
When the X-431 diagnostic instrument receives the "Clear the trouble code" order sent through the serial inter-
face, the trouble code inside the ECU will be cleared. However, if an internal trouble code is recorded or has a
collision record, it will not carry out this order.
(a) Malfunction status display.
When the working voltage is supplied to the SRS-ECU through a battery, the SRS-ECU will light the warning
lamp to inspect the light bulbs. During the initialization stage, the warning lamp will remain on for 6-7 s, and
in order to inform the driver that the system has a malfunction, the warning lamp will continue to remain on
after the working voltage is supplied. If the history trouble code’s quantity is less than 16, the warning lamp
will remain lit for 6-7 s after turning the ignition on and then turn off automatically. If the history trouble code’s
quantity is 16 and the current malfunction appears, it will be recorded and the first history malfunction record
will be automatically removed.
(b) Malfunction indicator.
When the system has malfunctioned, the warning lamp will be always on.
A displayed or history malfunction can only be reset by service personnel. A SRS-ECU internal malfunction or
malfunction’s "collision record" cannot be reset. In this situation, the SRS-ECU mus\
t be replaced.
(c) Microcontroller - independent warning lamp is lit.
The controller has a self-diagnosis function. If the inner controller malfunctions, the warning lamp will always
be on.
(d) If the airbag warning lamp is always on, please inspect it according to the following steps.
The first step of inspecting any of the malfunctions is to detect the malfunction’s position with a scanner. Then
carry out the inspection using the corresponding part’s inspection method. If the scanning result is an internal
malfunction or having to do with airbag execution, the SRS-ECU can be di\
rectly replaced.

Downloaded from www.Manualslib.com manuals search engine 223Airbags
Diagnostic procedures
StepsInspectionOperation
1
Inspect the clock spring
Warning
If not handled properly, the airbag module may deploy
and cause serious operator injury. Therefore, before
maintenance, please read the maintenance warnings
carefully.
See also airbag system maintenance warning
Are the components relating to the clock spring work-
ing normally? (The relationship between each pin is
normal, no unnecessary short or open circuit, etc.).
NormalGo to the next step
Abnormal
Replace the clock spring
See also airbag system and clock
spring removal/installation
2
Check whether the malfunction is on the driver side
airbag module or other components
Replace with a good DAB module
Install the battery's negative cable
Set the ignition switch to the "ON" position
Is the trouble code still displayed? Or can it be cleared?
Yes
Replace the driver side
airbag module
See also airbag system and
driver side airbag module
removal/installation
NoGo to the next step
3
Inspect the clock spring's wire harness connectors
Set the ignition switch to the "LOCK" position
Loosen the battery's negative cable and wait for at least
1 min
Take out the steering column housing
Loosen the clock spring connector
Is the clock spring working normally?
NormalGo to the next step
AbnormalReplace the wire harness
4
Check whether the malfunction is on the clock spring
or other components
Set the dedicated detector at 2 Ω position
Install the battery's negative cable
Set the ignition switch to the "ON" position
Is a trouble code displayed?
YesGo to the next step
No
Replace the clock spring
See also airbag system and clock
spring removal/installation
5
Check the wire harness between the clock spring and
SRS electronic control unit
Set the ignition switch to the "LOCK". position
Loosen the battery's negative cable and then wait for at
least 1 min
Take out the glove box (with the front passenger side
airbag module)
L o o s e n t h e f r o n t p a s s e n g e r s i d e a i r b a g m o d u l e
connectors
Take out the dashboard base
Loosen all the SRS airbag system unit connectors
Check the wire harness of the connectors and terminal
studs between the SRS airbag system electronic control
unit and the clock spring to determine whether they
have the following problems
• Ground
• Short connected with the power supply
• Open circuit
Is the above wire harness normal?
Normal
Replace the SRS airbag system
unit
See also SRS airbag system
SRS airbag system unit removal/
installation
AbnormalReplace the wire harness
6
Check the clock spring connector
Loosen the clock spring connector
Is the clock spring connector normal?
NormalGo to the next step
AbnormalReplace the wire harness
or connectors

Downloaded from www.Manualslib.com manuals search engine 225Airbags
Diagnostic procedures
StepsInspectionOperation
1Is the vehicle equipped with a front passenger side
airbag module?
YesGo to the next step
NoLine fault, inspect the wire harness
2
Check the front passenger side airbag module connec-
tor warning
• If not handled properly, the airbag module may deploy
and cause serious operator injury. Therefore, before
maintenance, please read the maintenance warnings
carefully.
See also airbag system maintenance warning
Set the ignition switch to the "LOCK" position
Loosen the battery's negative cable and wait for at least
1 min
Take the glove box off
Loosen the front passenger side airbag module connec-
tors
Is the front passenger side airbag module connector
normal?
Normal
[Current trouble code]
Go to the next step
[History trouble code]
Go to the next step
AbnormalReplace the wire harness
3
Check whether the malfunction is on the front passen-
ger side airbag module or the other components
Connect a good module with the front passenger side
airbag module connector's A and B terminal studs
Connect the battery's negative cable
Set the ignition switch to the "ON" position
Is a trouble code displayed?
YesGo to the next step
No
Replace the front passenger side
airbag module
See also airbag system and front
passenger side airbag module re-
moval/installation
4
Inspect the wire harness between front passenger side
airbag module and SRS airbag system electronic con-
trol unit
Set the ignition switch to the "LOCK" position
Loosen the battery's negative cable and then wait for at
least 1 min
Take the steering column housing off
Loosen the clock spring connector
Loosen the driver side and front passenger side airbag
module connectors
Take out the dashboard base
Loosen all the SRS airbag system unit connectors
Inspect the circuit between the connector terminal stubs
of SRS airbag system electronic control unit and front
passenger side airbag module, and check if it has the
following problems
• Ground
• Short connected with the power supply
• Open circuit
Is the related wire harness normal?
Normal
[Current trouble code]
Replace the SRS airbag system
unit
See also SRS airbag system
SRS airbag system unit removal/
installation
[History trouble code]
Fault diagnosis complete
AbnormalReplace related wire harness