Getting to Know Your Canyon6
Child Restraints (LATCH)
Your vehicle is equipped with LATCH
anchors, and may have top tethers for
use with a LATCH compatible child
restraint. If your child restraint is notcompatible with the LATCH system, you
may still use it by installing the childrestraint with the safety belt system.
Automatic Door Locks
(if equipped)
For your safety, vehicles equipped with
power door locks and Remote KeylessEntry are programmed at the factory to
lock all doors automatically. The doorswill lock when all doors are closed, theignition is on and the gearshift lever ismoved out of Park on vehicles with anautomatic transmission, or when vehicle
speed is greater than 15 mph on vehi
cles with a manual transmission. Thisfeature cannot be disabled.
You can personalize the automatic
unlock features through the DriverInformation Center.
See Sections 2 and 3 of your Owner Manual.
Rear Door Security Locks
(Crew Cab models)
Crew Cab models are equipped with
rear door security locks that allow you tolock the rear doors so they cannot beopened by passengers from the inside.
The lock switch (shown above) is locat
ed on the inside edge of each rear door.
Install a comfort guide on a shoulder
belt
1. Pull the elastic cord out from between
the seatback and the interior body toremove the guide from its storageclip.
2. Slide the guide under and past the
safety belt (the elastic cord must beunder the belt).
3. Place the guide over the belt and
insert the two edges of the belt intothe slots of the guide. (Be sure thatthe belt is not twisted and that it lies
flat. The elastic cord must be underthe belt and the guide on top.)
4. Buckle, position and release the
safety belt as described in Section 1 of your Owner Manual. Make sure
the belt crosses the passenger’s
shoulder.
Storing the Child Comfort Guide
To remove and store the comfort guides,
squeeze the belt edges together so thatyou can take them out of the guides.Slide the guide back on its storage cliplocated between the interior body andthe seatback. Storing the comfort guideproperly will prevent possible rattling.
See Section 1 of your Owner Manual.
Choose a child restraint that is appropri
ate for the child’s age and size (weightand height).
See Section 1 of your Owner Manual.
Canyon 2008 A 4/3/07 12:36 PM Page 6
17
(manual transmission). The preferred
method for shifting into 4LO is to have the vehicle moving at just under 3 mph (5 km/h).
2. Press and release the 4LO button
and wait for the 4LO indicator light to stop flashing and remain illuminated before shifting the transmission into gear or releasing the clutch pedal.
Shift from 4LO to 2HI or 4HI
1.Stop the vehicle or drive at 3 mph
(5 km/h) or slower, with the transmis
sion in Neutral (automatic transmis sion) or the clutch pedal depressed
(manual transmission). The preferred method for shifting out of 4LO is to have the vehicle moving at just under 3 mph (5 km/h).
2.Press and release the 2HI or 4HI
button and wait for the 2HI or 4HI indicator light to stop flashing and remain illuminated before shifting the transmission into gear or releasing the clutch pedal.
Note: When shifting into and out of
4LO, it is normal to hear and feel positive gear feedback, typically referredto as “clunk” (noise) and seat “bump”(feel). If a shift is made with the vehiclestopped, the indicator light may remain
flashing slowly. It may be necessary toshift the transmission momentarily intoReverse and Drive (automatic transmis
sion) or Reverse and 1st (manual trans mission) and rock the vehicle slightly to
get the light to come on fully.
N(Neutral): Shift the vehicle’s transfer
case to N only when towing your vehicle.
4 (4HI): This setting engages the front
axle to provide extra traction on snowy
or icy roads and during most off road
situations. Do not drive on pavement in
four wheel drive for long periods, as it
may cause premature powertrain wear.
4 (4LO): This setting engages the
front axle and sends maximum power toall four wheels for extremely low traction
conditions. You might choose 4LO for
driving off road in sand, mud or deepsnow and climbing or descending steephills.
Indicator lights in the buttons show
which setting is currently selected.
Shift from 2HI to 4HI
• Press the 4HI button while driving at
any speed.
Shift from 4HI to 2HI
• Press the 2HI button while driving at
any speed.
Shift from 2HI or 4HI to 4LO
1. Stop the vehicle or drive at 3 mph
(5 km/h) or slower, with the transmis
sion in Neutral (automatic transmis sion) or the clutch pedal depressed
Note: The indicator lights can flash at
two speeds. Fast flashing means theconditions were not met to make thedesired shift; typically, the vehicle was
going too fast, the automatic transmis
sion was not in Neutral, or the clutchpedal was not fully depressed. Slowflashing means the shift is in progress. If the transfer case is unable to make arequested shift, the indicator light willflash slowly for 30 seconds and thenreturn to the previous setting.
Canyon 2008 A 4/3/07 12:36 PM Page 17
