2008 GEELY MK wheel

Front Suspension SystemFront Strut Assembly4-46Section 4 Front Strut AssemblyReplacement1. Remove screen wiper arm cover
2. Remove right screen wiper
3. Remove left screen wiper
4. Remove hood and seals of vehicle neck
5. Remove upper right ventilation shield of vehicle neck
6. Remove upper left ventilation shield of vehicle neck
7. Remove the wiper linkage assembly of windscreen
8. Remove the hood of vehicle neck
(1) Remove the bolt and 2 clips, disconnect the harness
(2) Remove the hose and harness (wiper)
(3) Remove the 8 bolts of ventilation shield of vehicle neck
9. Remove the front wheel
10. Remove the brake hose
(1) Remove the bolts, brake hose and the clamp of ABS sensor
harness from the shock absorber bracket (with ABS)
(2) Remove the bolts and brake hose from the shock absorber
(without ABS)
11. Remove the front shock absorber with helical spring
(1) Remove the shock absorber from knuckle after remove the two
nuts and bolts.
(2) Remove the front shock absorber with helical spring, remove
the three bolts mounting suspension bracket
12. Fix the front shock absorber with helical spring
(1) Mount the two bolts and one bolt onto the bracket of shock
absorber underside, and fix it onto the vise
(2) Hold down the helical spring
Notice: Don't use the impact wrench which can damage the
special tool-

Front Suspension System-Front Strut Assembly4-4828. Mount the dust seals of left front suspension bracket
29. Mount the left front suspension bracket sub-assembly
30. Mount the front bracket onto the left front shock absorber nuts
(1) Hold the bracket by two bolts and a screwdriver or analogue.
Mount the new centre nut
Torque: 33N.m
Notice: DonÕt cause damage to the stud of suspension bracket.
(2) The special tool for remove
(3) Apply the multipurpose grease onto the suspension bracket
31. Mount the dust cap of left front suspension bracket
32. Mount the front stud assembly
(1) Mount the #2 suspension bracket
(2) Mount the front stud assembly by three nuts
Torque: 39N.m
(3) Mount the shock absorber onto the knuckle
(4) Film the engine oil onto the thread of two nuts
(5) Mount the two bolts and nuts
Torque: 132N.m
33. Mount the brake hose
Torque: 29N.m
34. Mount the front wheel
Torque: 103N.m
35. Mount the outside cover of vehicle neck
(1) Mount the outside cover of vehicle neck by 8 bolts
Torque: 5N.m
(2) Connect hose and harness (screen wiper)
(3) Mount the harness by bolts and two clips
36. Mount the linkage assembly of windshield wiper
37. Mount the ventilation hood of left vehicle neck
38. Mount the ventilation hood of right vehicle neck
39. Mount the engine hood and seals of vehicle neck
40. Mount the left front wiper arm
41. Mount the right front wiper arm
42. Check and adjust the front wheel alignmentMulti-purpose grease

Front Suspension System-Front Lower Swing Arm Assembly4-49Section 5 Front Lower Swing Arm AssemblyDisassemble1. Remove the front wheel
2. Remove the subassembly of the engine #1 cover
3. Remove the engine hood
4. Sling the engine assembly
5. Remove the left front suspension cross beam
Remove the two bolts and left front suspension cross beam
6. Remove the right front suspension cross beam
Remove the two bolts and right front suspension cross beam
7. Disassemble the left lower subassembly of the front suspension
arm
(1) Remove the clips and nuts
(2) Remove the suspension arm from the knuckle by special tool
8. Disassemble the front stabilizer bar
(1) Remove the nuts, three retainers and two pads (left side) when
tightening the bolts of stabilizer rod
(2) Take the same steps on the other side as above.
(3) Remove the front stabilizer rod after removing four bolts
9. Disassemble the power rack & pinion gear assembly
Disassemble the power rack & pinion gear assembly by removing
two bolts
Tips: Pull up the power rack & pinion gear assembly.

4-5217. Mount left lower front suspension subassembly
(1) Mount the lower suspension arm onto the knuckle by nuts
Torque: 98N.m
(2) Mount a new clip
Notice: Further tighten nuts for 60° if the holes are not in the
correct alignment
18. Mount the left front suspension cross beam
Mount the left front suspension cross beam with two bolts.
Torque: 47N.m
19. Mount the right front suspension cross beam
Mount the right front suspension cross beam with two bolts
Torque: 47N.m
20. Mount the front wheel
Torque: 103N.m
21. Stabilize the suspension
Stabilize the front suspension
22. Sufficiently tighten left front lower suspension arm subassembly
Tighten the lower suspension arm with two bolts
Bolt A: 88N.m
Bolt B: 132N.m
Attention: Don't rotate the nuts
23. Install engine hood.
24. Check and adjust front wheel alignmentFront Suspension System-Front Lower Swing Arm Assembly

Section 6 Front Stabilizer Bar and Link Rod AssemblyDisassemble1. Remove the front wheel
2. Remove the front stabilizer bar bolts
(1) Remove two nuts, five retainers, four pads and stabilizer bolts when fixing bolts
(2) Take the same steps on other side as above.
3. Remove the front stabilizer bar
Remove four bolts and #1 front stabilizer bar bracket.
4. Mount the front stabilizer bar
Mount the stabilizer bar, two bushings, bracket and four bolts.
Torque: 37N.m
Notice:
Make the groove toward the vehicle rear
Tip:
Keep the bushing outside the paint line
5. Mount the front stabilizer bolts
(1) Mount the front stabilizer bolts, four pads and five retainers
Torque: 18N.m
(2) Take the same operations on other side as above process
6. Mount the front wheel
Torque: 103N.m4-53Installation markFront Suspension System-Front Stabilizer Bar and Link Rod Assembly

I. Rear suspension structure description This model uses strut independent rear suspension with stabilizer bar.
Rear suspension consists of the parallel front and rear double transverse arms, trailing rod, rear stabilizer bar
and rear strut assembly. The shock absorber and cone coil spring are arranged eccentrically.
See the table below for the major technical parameters of the rear suspensionII. Symptom Table Use the table below to help you find the cause of the problem. The numbers indicate the priority of the likely
cause of the problem. Check each part in order. If necessary, replace these parts.Suspected Area
1. Tires (Worn or improperly inflated)
2. Wheel alignment (Incorrect)
3. Hub bearing (Worn or damaged)
4. Suspension parts (Worn or damaged)
1. Vehicle (Overloaded)
2. Spring (Stiffness small)
3. Shock absorber (Worn)
1. Tire (Worn or improperly inflated)
2. Wheel (not within specification)
3. Shock absorber (Worn)
1. Tire (Worn or improperly inflated)
2. Wheel alignment (Incorrect)
3. Shock absorber (Worn)
4. Wheel (not within specification)
1. Tire (Worn or improperly inflated)
2. Wheel alignment (Incorrect)
3. Shock absorber (Worn)
4. Suspension parts (Worn or damaged)Symptom
Off track
Body descent
Sways
Rear wheel shimmy
Abnormal tire wearRear Suspension System-Rear Suspension System4-55Item
Shock absorber operating cylinder diameter /mm
Shock absorber piston rod diameter/mm
Shock absorber stroke /mm
Camber
Toe in/mm
Remark: Wheel alignment parameter is at free loadParameter
38
12.4
250
-0°56' ± 45'
3 ± 3

Check1. Check the tire
2. Measure the vehicle height
Notice:
Adjust the vehicle height to specified value before check the
wheel alignment
3. Check the rear toe-inSection 2 Rear Wheel AlignmentRear Suspension System-Rear Wheel Alignment4-56A+B: 0°19' ± 19' (0.31 ± 0.31°)
C+D: 3.0 ± 3.0mmToe in
( assembly ) Check and replace the related suspension parts if the toe in out of spec.
4. Check the camber
(1) Mount the camber-caster-kingpin measuring device, place the vehicle on the wheel position device
(2) Check camber
Check the damage and performance decline of suspension parts and replace if necessary, if measurement out
of spec.-0°56' ± 45' (-0.93° ± 0.75°)
45' (0.75°) or smallerCamber
Left-right deviationFront

Section 3 LH/RH Rear Suspension Coil SpringReplacement1. Remove rear wheel
2. Remove the wire of the wheel speed sensor(with ABS)
(1) Remove the connector of wheel speed sensor.
(2) Remove bolts and wheel speed sensor from rear axle
frame.
Notes:
Remove the right sensor wire by using same process as left.
3. Remove the load-sensing valve bracket (without ABS)
Remove two nuts and load-sensing valve bracket from the axle
bracket
4. Remove the proportioning valve and rear right brake tube
(1) Remove the proportioning valve and rear right brake tube by
the special tool
(2) Remove the clips
Notes: Don't reuse the clips
5. Remove the proportioning valve and rear left brake tube
Notes: use the same operations of the proportioning valve and
rear right brake tube to remove #3 rear brake tube.
6. Remove right parking brake cable assembly
Remove nuts and right parking brake cable assembly
assembly from rear axle frame
7. Remove left parking brake cable assembly
8. Loose the rear axle assembly
Loose two 2 boltsRear Suspension System-LH/RH Rear Suspension Coil Spring4-57