2008 GEELY FC wiring

Windshield/bodywork glass/wing mirror--Fogbroom system
Fog defrost system
Position drawing
Malfunction
All demists (defrosts) do not work
Rear ventilation window Demist (defrost)
do not work
electric rear mirror defrost dose not workcomponents name
1. DEF main relay
2. DEF-IP fuse
3. DEF-m fuse
4. demist switch
5. wiring harness
1. demist wire
2. wiring harness
1. electric rear mirrorreference pages
Malfunction phenomena table
Demist (Defrost)switch
 327 
Demist wire

Windshield/bodywork glass/wing mirror--Electric rearview mirror control system
Positions
Trouble table
Trouble
rearview mirrors do not work
rearview mirrors work abnormallyComponents name
1. (accessory) fuse
2. rearview mirror switch
3. wiring harness
1. rearview mirror switch
2. wiring harnessReference page
-
332
-
332
-
 331 
Left rear view mirrorsElectric rear view mirrors
switch
Right rearview mirrors

Panel/combination instrument--combination instrument
2. Inspect output signal of vehicle speed.
(1) When vehicle run at 10km/h, inspect voltage between ter-
minal10 and terminal A1 of combination instrument assembly.
Standards: the voltage pulsates repeatedly between
0V to 5V for thirteen times.
Notes: Inspect the ignition switch “on” connects the
joint
3. Inspect speed gauge
(1) Connect a test tachometer. then startup the engine.
Notes:
zTachometer terminals polarity connects oppositely will damage interior transistors and
LEDs.
zWhen move or disassemble tachometer. do not drop on the ground or knock the surface.
(2) Compare indicted value test tachometer and combination instrument tachometer.
Standard indicted value (rmp) permitted values (rpm)
700 630-770
1,000 (900-1,100)
2,000 (1,850-2,250)
3,000 2,850-3,150
4,000 (3,800-4,200)
5,000 4,750-5,250
6,000 (5,700-6,300)
7,000 6,650-7,350
DC 13.5V, 25°C
(1) Disassemble the joint of fuel meter
(2) Turn ignition switch to ON, inspect indictor position of fuel guage.
Indictor position: F
(3) Connect short terminal1 and terminal2 of wiring harness sides. Turn ignition switch to ON, inspect
indictor position of fuel guage.
Indictor position: F
5. Inspect low fuel level indictor 4. Inspect fuel gauge
The fuel gauge has the function of sensor detection (that is
failure treatment of oil level tachometer)that is when fuel gauge
indictor is at E position, if low oil level warning light doesn”t
light, first should judge whether there have open-loop trouble of
fuel sensor or wiring harness. When sensor fails, fuel indictor
should stop at current position. But if failing time is over 20
seconds, the indictor will return to E position quickly, the in-
strument will at wire break detection. If the normal situation of
detection panel is over 20 seconds, indicator will return to normal.
A1A20
 336 

Panel/combination instrument--combination instrument
(1) Disassemble fuel meter joints or break wire, when indictor is at E, fuel indictor does not light.
(2) Jumper a 300-330
resistor from the corner of terminal1 and termianl2, turn ignition switch to ON,
indictor is at E line, the indictor light lights.
6. Inspect generator water thermometer .
(1) Disassemble joint of generator water thermometer
(2) Turn ignition switch to ON, inspect indictor position of gen-
erator water thermometer.
Indictor position: COOL
(3) Earth 2 terminal of the wiring harness side joint to inspect
indictor position of generator water thermometer.
Indictor position: HOT
1 2 3
7. Inspect untied indictor light of driver seat belt.
(1) Turn ignition switch to ON, Inspect untied indictor light of driver seat belt lights.
(2) Tie the seat belt, inspect untied indictor light seat belt lights off.
(3) Disassemble the joint of safe belt button switch, earth the terminals of wiring harness
(4) Turn ignition switch to ON, inspect untied indictor light seat belt lights on.
8. Inspect low oil pressure indictor
(1) Disassemble the joint of oil pressure switch.
(2) Turn ignition switch to ON.
(3) Earth terminals of wiring harness sides, inspect low oil pressure indictor.
Low oil pressure indictor: light
9. Inspect oil pressure switch
(1) disassemble joints of oil pressure switch,
(2) Inspect the conduction of oil pressure switch terminals and earth.
Generator extinguishes: conduction
Generator works: not conduction
10. Inspect light warning buzzer
(a) Inspect the function of light warning buzzer
Clues on: light warning buzzer works together, only key
reminding buzzer works.
(1) Front combination light switch switches to ON, extract the
key, open driver seat door, inspect light warning buzzer.
Audio buzzer: Audio for 10 seconds in the night to cut
lamp power, in the day cut the lamp instantly.
(2) When buzzer works, do any one of the followings, inspect whether buzzer stop buzzing.
z zz z
zTurn front combination switch to OFF.
z zz z
zClose driver seat door.
z zz z
zInsert the key.
Buzzer Light switch
Key warning
switch
Pull out the key
Open driver door
 337 

Panel/combination instrument--combination instrument
(b) Inspect light warning buzzer function
(1) Disassemble combination instrument.
(2) Connect battery positive wire to terminal A5 and nega-
tive to terminal A1 and A2.
(3) Connect battery positive wire to terminal A18 and nega-
tive to terminalA17,inspect buzzer.
Audio buzzer: long buzzes
(4) When buzzer works, connect battery positive wire to ter-
minal A4,inspect whether buzzer stop working.
11. Inspect key buzzer
(a) Inspect when key buzzer and light warning buzzer works
together, only key buzzer works.
(1) Insert the key, when driver seat door opens, turn ignition
switch to OFF (LOCK or ACC). inspect key buzzer works
1HZ discontinuously.
(b) inspect key buzzer function
(1) Disassemble combination instrument.
(2) Connect battery positive wire to terminal A5 and nega-
tive to terminal A1 and A2.
(3) Connect battery negative wire to terminal A17 and B8,
inspect buzzer which should work discontinuously.
(4) When buzzer works, connect battery positive wire to ter-
minal A4,inspect whether buzzer stop working.
12. Inspect brake system indictor
(a) Inspect parking brake system indictor
Key warning
switch
Key switch
1G gear
Pull out the key
Open driver door
Buzzer
B8
B1
A1A20
(1) Disassemble the joint of parking brake switch, and earth terminals of wiring harness side joints.
(2) Turn ignition switch to ON, inspect brake system indictor light lights.
(b) Inspect brake oil level indicator light
(1) Disassemble the joint of brake oil level indicator light, connect terminal of wiring harness side
joints.
(2) Turn ignition switch to ON, inspect brake system indicator light lights.
 338 

Anti-stealing and door lock--Electric door lock control system
Malfunction phenomenon
“Door locker control system” does not work
(all).
Door locking/unlocking malfunction (use
handle operation and key operation)
Door locking/unlocking malfunction (use
key)
Malfunction of key keeping protection func-
tion
Only one door locker does not workPossible malfunction part
1. DOOR fuse (panel J/B)
2. Wiring harness
1. Electric window main switch (door control switch)
2. Wiring harness
1.
Door at the side of driver assembly (door control switch)
2. Wiring harness
3. Door locker connecting rod is loosen
1. Anti-versa lock supervising switch
2. Door control light switch
3. Wiring harness
1. Door locker electric motor
2. Wiring harnessReferred page
-
-
359
-
359
-
-
359
-
-
359
-
Malfunction phenomenon table
 358 

Electric sunroof (optional)--Sunroof
Bolt
Screw cap
Electric sunroof (optional)
Sunroof
Overhaul
Hint: when assembling, please work by the sequence which is opposite with disassembling
sequence; but when it has items that need to pay special attention, it will add special specification.
1. Disassemble inner trim board of top (referring to page 390).
2. Disassemble the glass of sunroof.
(a) Use planetary wrench to disassemble planetary screw.
(b) Pull the glass upwards to disassemble it.
3. Disassemble waterproof adhesive tape of sunroof.
4. Disconnect connection of wiring harness.
5. Disassemble shell body of sunroof.
(a) Disassemble four drain hoses.
(b) Liking that shown in figure, disassemble four bolts and six screw caps, then disassemble shell body.
6. Disassemble trim sun shade of sunroof.
(a) Disassemble the screw and stopper.
(b) Disassemble trim sun shade of sunroof.
 362 

Electric sunroof (optional)--Sunroof system
Inspection for sunroof switch
(a) Check the function of switch. Disassemble front top light,
and disassemble the joint of front top light, then check the
joint at the side of switch liking that shown in figure.
Malfunction phenomenon table Position of parts
Malfunction phenomenon
Sunroof system does not work
Sunroof system works abnormallyPossible malfunction part
1. Ignition switch.
2. Control switch of sunroof.
3. 25A, 15# fuse.
4. Wiring harness
1. Control switch of sunroof.
2. Wiring harnessReference page
-
-
-
-
-
-
 365 
Terminal connected by avometer
2-4
2-5ConditionSpot contact or press
keystroke 2 for long time
Spot contact or press
keystroke 1 for long time
Regulated situa-
tion
Conduction
Conductiion
Shell body of sunroof
Motor of sunroof
Switch of sunroof