2008 FORD MUSTANG maintenance

Changing the air filter element
1. Release the clamps that secure
the air filter housing cover.
2. Carefully separate the two halves
of the air filter housing.
3. Remove the air filter element
from the air filter housing.
4. Wipe the air filter housing and
cover clean to remove any dirt or
debris and to ensure good sealing.
5. Install a new air filter element. Be
careful not to crimp the filter
element edges between the air filter
housing and cover. This could cause
filter damage and allow unfiltered
air to enter the engine if not
properly seated.
6. Replace the air filter housing
cover and secure the clamps.
MOTORCRAFT PART NUMBERS
Component 5.4L DOHC Supercharged V8 engine
Air filter element FA-1807
Fuel filter FG-1083
Battery BXT-40-R
Oil filter FL-820S
PCV valve EV-270
Spark plugs* AGSF-22FM1
* Refer to Vehicle Emissions Control Information (VECI) decal for spark
plug gap information.
2008 05+ Mustang(197)
Supplement
USA(fus)
Maintenance and Specifications
35

REFILL CAPACITIES
Fluid Ford Part Name Capacity
Brake fluidMotorcraft High
Performance DOT 3
Motor Vehicle Brake
FluidBetween MIN and
MAX lines on reservoir
Engine oil (includes
filter change)Motorcraft 5W-50 Full
Synthetic Motor Oil6.5 quarts (6.1L)
Engine coolant
1
Motorcraft Premium
Engine Coolant
(green-colored) or
Motorcraft Premium
Gold Engine Coolant
(yellow-colored)21.1 quarts (20.0L)
Intercooler coolant
1
Motorcraft Premium
Engine Coolant
(green-colored) or
Motorcraft Premium
Gold Engine Coolant
(yellow-colored)3.96 quarts (3.75L)
(See your authorized
dealer for service)
Power steering fluidMotorcraft
MERCON
VATFBetween MIN and
MAX lines on reservoir
Rear axle lubricant
2
Motorcraft SAE
75W-140 High
Performance Synthetic
Rear Axle Lubricant4.25 pints (2.0L)
Fuel tank — 15.7 gallons (59.4L)
Transmission fluid
3MERCON
V ATF 6.35 pints (3.5L)4
Windshield washer
fluidUltra-Clear Windshield
Washer Concentrate4.0 quarts (3.8L)
1Add the coolant type originally equipped in your vehicle.2Rear axle lubricants do not need to be checked or changed unless a
leak is suspected, service is required or the axle assembly has been
submerged in water. The axle lubricant should be changed any time the
rear axle has been submerged in water, using SAE 75W-140 High
Performance rear axle lube, meeting Ford specification WSP-M2C102–A.
2008 05+ Mustang(197)
Supplement
USA(fus)
Maintenance and Specifications
36

Fill 1/4-9/16 in (6-14 mm) below bottom of fill hold. Add 4 oz. (118 ml )
of Addictive Friction Modifier C3AZ-19B546-A or equivalent meeting
Ford specification EST-M2C118-A for complete refill of Traction-Lok
axles.
3The Tremec TR-6060 6–Speed manual transmission on your Shelby
GT500 uses MERCON
V automatic transmission fluid. Ensure that the
correct MERCON
V ATF automatic transmission fluid is used as
indicated on the label on your transmission.
4Service refill capacity is determined by filling the transmission to the
bottom of the filler hole with the vehicle on a level surface.
USING THE RIGHT BULBS
Function Trade Number
Park lamp, turn lamp, side marker (front) 3156K
Luggage compartment lamp S211
Fog lamp PS24N
DRIVETRAIN
2008 05+ Mustang(197)
Supplement
USA(fus)
Maintenance and Specifications
37

Item Description
Rear axle8.8 in. solid rear axle with limited-slip
differential 3.31:1 ratio
Driveshaft2 piece steel
TransmissionTremec TR–6060 6-speed manual with integral
clutch housing
Gear ratiosGear Ratio
1st 2.97
2nd 1.78
3rd 1.30
4th 1.00
5th 0.80
6th 0.63
Reverse 2.90
ENGINE INFORMATION
Item Description
ConfigurationLongitudinally mounted, 90-degree
V8, cast-iron cylinder block and
cast aluminum cylinder heads
Bore x Stroke90.2 x 105.8 mm (3.55 x 4.165 in)
Displacement5410 cc/330 cid
Compression ratio8.4:1
Horsepower500 Horsepower @ 6000 rpm
Torque480 lb-ft torque @ 4500 rpm
Redline6000 rpm redline
6250 rpm fuel shut-off
Specific output92.6 HP per liter
ValvetrainDual overhead chain-driven cams,
roller finger followers with
hydraulic lash adjustment,
ovate-wire valve springs, four
valves per cylinder
Fuel systemSequential electronic fuel injection
2008 05+ Mustang(197)
Supplement
USA(fus)
Maintenance and Specifications
38

Item Description
Mass air sensor130.5 x 80.5 mm (3.54 in) oval
Throttle bodyTwin 60 mm (2.36 in) diameter
bore-simultaneously open
PistonsForged aluminum
CrankshaftForged steel
Connecting rodsForged steel I-beam
SuperchargerEaton model 122, Roots-type
Exhaust manifoldsCast high-silicon, molybdenum iron
Exhaust systemDual stainless steel
Engine drivebelt routing
5.4L DOHC 32V Supercharged V-8
2008 05+ Mustang(197)
Supplement
USA(fus)
Maintenance and Specifications
39

WARRANTY COVERAGE
The Shelby GT500 carries the same New Vehicle Limited Warranty as
other Ford Mustang models. This information is covered in its entirety in
the Ford Motor Company Warranty Guide.
Warranty service for the Shelby GT500 or any SVT vehicle can be
obtained at any Ford or Lincoln Mercury dealer nationwide.
SVT does not recommend modifying or racing SVT vehicles, as they are
designed and built to be driven as delivered from the factory. The Ford
Motor Company Warranty Guide discusses vehicle usage and the
installation of aftermarket parts and their effect on warranty coverage as
follows:
Repairs are not reimbursable under warranty when damage is caused by:
•misusing the vehicle, such as driving over curbs, overloading, racing,
or using the vehicle as a stationary power source.
•altering or modifying the vehicle — including the body, chassis, or
components — after the vehicle leaves Ford’s control.
•non-Ford parts installed after the vehicle leaves Ford’s control,
including, but not limited to, cellular phones, alarm systems and
automatic starting systems.
Please see the Warranty Guide for complete information.
In the event the vehicle is intended for track use, and the loss of
warranty coverage is not of concern, the following powertrain durability
modifications are recommended:
•install transmission oil cooler. Permanent damage to the transmission
will result if the vehicle is subjected to competition conditions without
installation of a transmission oil cooler.
•install rear differential cooler. Permanent damage to the rear
differential will result if the vehicle is subjected to competition
conditions without installation of a differential cooler.
Additionally, perform Multi-Point Inspection and the inspections outlined
in the 120,000 mile Normal Maintenance Schedule outlined in the
Scheduled Maintenance Guide. Refer to the Vehicle Service Manual for
removal and installation procedures. Replace with Genuine Ford and
Motorcraft service parts as needed.
These modifications will not necessarily protect your engine from
damage in competition conditions. Subjecting your vehicle to competition
conditions even with these proposed modifications will render repairs
non-reimbursable under the New Vehicle Limited Warranty.
2008 05+ Mustang(197)
Supplement
USA(fus)
A word about warranty coverage
40