2008 FIAT IDEA change wheel

59
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
fig. 70F0H0071mfig. 71F0H0070mfig. 72F0H0072m
DIRECTION INDICATORS fig. 70
Push the stalk to (stable) position:
❒up (position 1): right-hand indicator
ON;
❒down (position 2): left-hand indicator
ON.
Warning light
For Dstart flashing on the
instrument panel.
Indicators are switched off automatically
when the steering wheel is straightened.
If you want the indicator to flash briefly
to show that you are about to change
lane, move the stalk up or down without
clicking into position (unstable position).
When released, the stalk will return to
its home position.“FOLLOW ME HOME”
DEVICE fig. 71
This function allows the illumination of the
space in front of the car for a preset pe-
riod of time.
Activation
With the ignition key on STOPor
removed, pull the stalk towards the
steering wheel within 2 minutes from
when the engine is turned off.
At each single movement of the stalk,
the time in which the lights stay on is
extended by 30 seconds up to maximum
210 seconds. After this time, the lights
go off automatically. AUTOMATIC LIGHT SENSORS
(dusk sensor) (where provided)
This sensor detects any changes in the
external brightness according to the
sensitivity of the set light level: the high-
er the sensitivity, the lower the amount
of external light needed to switch the
lights on. The sensitivity of the dusk sen-
sor is adjusted by means of the “Setup
menu” on the “Multifunctional Display”.
Activation
Rotate the knurled ring in position
2A
fig. 72as to cause automatic switching
on of the side/tail lights and low beam
lights simultaneously depending on the
external brightness.
036-092 idea GB 1 ed 10-07-2008 16:12 Pagina 59

109
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
IMPORTANT The front air bags and/or
side bags may be deployed if the car is sub-
ject to heavy knocks or accidents involv-
ing the underbody area, such as for ex-
ample violent shocks against steps, kerbs
or low obstacles, falling of the car in big
holes or sags in the road.
IMPORTANT When the air bag inflates
it emits a small amount of dusts. These
dusts are harmless and is not the begin-
ning of a fire; then the unfold cushion sur-
face and the car interiors can be covered
by a dusty remains: this dust can irritate
skin and eyes. In case of contact, wash
yourself using neutral soap and water.
The air bag system has a validity of 14
years as to the pyrotechnic charge, and 10
years as to the twisted contact. As this
date approaches, contact Fiat Dealership
to have it replaced.
IMPORTANT Should an accident occur in
which any of the safety devices is activat-
ed, take the car to a Fiat Dealership to
have the devices activated replaced and to
have the system checked.
All check, repair and replacement opera-
tions concerning the air bags must only be
carried out c/o Fiat Dealership.If you are having the car scrapped, have
the air bag system deactivated at a Fiat
Dealership first. If the car changes own-
ership, the new owner must be informed
of the method of use of air bags and the
above warnings and also be given this
“Owner handbook”.
IMPORTANT The triggering of preten-
sioners, front air bags and front side bags
is decided in a differentiated manner. The
failure to deploy one or more of them
does not mean that the system is not
working properly.
Never rest head, arms and
elbows on the door, on the
windows and in the window bag area
to prevent possible injuries during the
inflation phase.
WARNING
Never put head, arms and el-
bows out of the window.
WARNING
If warning light ¬does not
come on when turning the
key to MAR or if it stays on when
travelling it could indicate a failure in
restraint systems; in this case air bags
or pretensioners could not trigger in
the event of an accident, or in a re-
stricted numbers of cases they could
trigger accidentally. Stop the car and
contact Fiat Dealership to have the
system checked immediately.
WARNING
GENERAL WARNINGS
Do not cover the back rest of
front seats with trims or cov-
ers there are not set for the use of side
bags.
WARNING
Always keep your hands on
the steering wheel rim when
driving, so that if the air bag is trig-
gered, it can inflate without meeting
any obstacles which could cause seri-
ous harm to you. Do not drive with
the body bent forwards, keep the seat
back rest in the erect position and
lean your back well against it.
WARNING
093-110 idea GB 1 ed 10-07-2008 8:28 Pagina 109

120
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
SNOW TYRES
Use snow tyres of the same size as the
normal tyres provided with the car.
Fiat Dealership will be happy to provide
advice concerning the most suitable type
of tyre for the customer’s requirements.
For the type of tyre to be used, inflation
pressures and the specifications of snow
tyres, follow the instructions given in para-
graph “Wheels” in section “Technical
specifications”.
The winter features of these tyres are re-
duced considerably when the tread depth
is below 4 mm. In this case, they should
be replaced.
Due to the snow tyre features, under nor-
mal conditions of use or on long motor-
way journeys, the performance of these
tyres is lower than that of normal tyres. It
is therefore necessary to limit their use to
the purposes for which they are certified.IMPORTANT When snow tyres are used
with a max speed index below the one
that can be reached by the car (increased
by 5%), place a notice in the passenger
compartment, plainly in the driver’s view
which states the max permissible speed of
the snow tyres (as per EC Directive).
All four tyres should be the same (brand
and track) to ensure greater safety when
driving and braking and better driveabili-
ty.
Remember that it is inappropriate to
change the direction of rotation of tyres.The max speed for snow
tyres with “T” marking is 190
km/h. The Road Traffic Code speed
limits must however be always strict-
ly observed.
WARNING
111-122 idea GB 1 ed 10-07-2008 8:29 Pagina 120

126
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
LOW ENGINE OIL
PRESSURE (red)
EXHAUSTED OIL (red)
(Multijet versions
with DPF)
Low engine oil pressure
When the ignition key is moved to MAR,
the warning light turns on and should go
out as soon as the engine is started.
The display will show the dedicated mes-
sage.
v
Exhausted oil
The warning light turns on and flashes
along with the message on the display
when the system detects that the engine
oil is exhausted.
After the first indication, at each engine
start-up, the warning light
vcontin-
ues to flash for about 60 seconds and then
every 2 hours until the oil is changed.“DUALDRIVE”
ELECTRIC POWER
STEERING FAILURE
(red)
When the ignition key is moved to MAR,
the warning light turns on and should go
off after a few seconds.
If the warning light stays on, the electric
steering system provides no assistance and
the effort on the steering wheel is in-
creased, although steering is still possible.
In this case, go to a Fiat Dealership.
The display will show the dedicated mes-
sage.
g
INCOMPLETE DOOR
LOCKING (red)
On certain versions the warn-
ing light turns on when one or
more doors or the tailgate are not prop-
erly closed.
The display will show the dedicated mes-
sage.
A buzzer is triggered when doors/tailgate
are open and the car is moving.
´
SEAT BELTS NOT
FASTENED (red)
(where provided)
The warning light on the display
lights up when the car is moving and the
driver’s seat belt is not correctly fastened.
The warning light flashes, and a buzzer is
triggered, if the driver’s seat belt is not
correctly fastened. The buzzer of the
S.B.R. (Seat Belt Reminder) system can be
disabled by the Fiat Dealership only. The
system can be enabled from the “setup”
menu.
elling (on certain versions together
with the message on the display) stop
the engine immediately and contact
Fiat Dealership.
WARNING
If the warning light vflashes, promptly contact
Fiat Dealership in order to have the
oil changed and the warning light on
the instrument panel turned off.
WARNING
123-132 idea GB 1 ed 10-07-2008 8:29 Pagina 126

135
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
fig. 2F0H0718m
IMPORTANT Do not directly connect the
two negative terminals: sparks could ignite
the flammable gas from the battery. If the
other battery is fitted in a vehicle, prevent
accidental contacts between the metal
parts of the two vehicles.Do not carry out this proce-
dure if you lack experience;
if it is not done correctly it can cause
very intense electrical discharges. In
addition, the fluid contained in the
battery is poisonous and corrosive.
Avoid contact with skin and eyes. You
are also advised not to put naked
flames or lighted cigarettes near the
battery and not to cause sparks.
WARNING
Under no circumstances
should a battery charger be
used to start the engine: it
could damage the electronic
systems and in particular the ignition
and injection control units.BUMP STARTING
Never bump start the engine (bu push-
ing, towing, or coasting downhill) as this
could cause fuel to flow into the catalytic
exhaust system and damage it beyond re-
pair.
IMPORTANT Remember that until the
engine has started the brake booster and
electrical power steering systems will not
work and a greater effort will therefore
be required to press the brake pedal or
turn the steering wheel.
Alert other drivers that the
car is stationary in compli-
ance with local regulations: hazard
warning lights, warning triangle etc.
Any passengers on board should leave
the car, especially if it is heavily laden.
Passengers should stay away from on-
coming traffic while the wheel is be-
ing changed on. If the wheel is being
changed on a steep or badly surfaced
road, place the wedges or other suit-
able material under the wheel to stop
the car.
WARNING
133-160 idea GB 1 ed 10-07-2008 8:30 Pagina 135

140
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
IF A TYRE IS
PUNCTURED
GENERAL INSTRUCTIONS
Wheel changing and correct use of the
jack and space-saver spare wheel call for
some precautions as listed below.
WARNING If the car is equipped with
“Kit for tyre quick repair Fix & Go”, see
the instructions contained in the follow-
ing chapter.
The space-saver spare wheel
is specific to the vehicle: do
not use it on other models and do not
use spare wheels designed for other
models on your car. The space-saver
spare wheel must only be used in the
event of an emergency, and then on-
ly for as little as possible and at no
more than 80 km/h. The space-saver
spare wheel is fitted with an orange
sticker giving the main instructions for
its use and limitations. The sticker
must never be removed or covered.
Do not fit the hub cap to the spare
wheel. The sticker gives the following
information in four languages: C
AU-TION! FOR TEMPORARY USE ONLY! 80KM/H MAX! REPLACE BY NORMAL WHEEL
AS SOON AS POSSIBLE. DO NOT COVER THIS
LABEL IN USE.
WARNING
When driving with a space-
saver spare wheel fitted, the
driving performance of your car may
change. Avoid accelerating or brak-
ing suddenly, steering abruptly or fast
cornering. The lifespan of a space-
saver spare wheel is approximately
3000 km, after which it will need to
be replaced with another spare wheel
of the same type. Never fit a standard
tyre on the space-saver spare wheel
rim. Have the wheel replaced and re-
fitted as soon as possible. Never use
two or more spare wheels at the same
time. Do not lubricate the bolt
threads before fitting them back: they
could come loose.
WARNING
133-160 idea GB 1 ed 10-07-2008 8:30 Pagina 140

141
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
The jack should only be used
to change a wheel on the car
for which it was designed. It should
not be put to other uses or employed
to raise other models of cars. Under
no circumstances should it be used
when carrying out repairs under the
car. An incorrectly positioned jack
may cause the car to fall. Do not use
the jack to lift loads exceeding that
indicated on the label attached to the
jack itself. Do not fit snow chains on
a space-saver spare wheel. If a front
wheel (drive wheel) is punctured and
you require snow chains to proceed,
take a standard wheel from the rear
axle and fit the space-saver spare
wheel in its place. Having fitted two
standard wheels on the front drive
axle you can use snow chains, thus
solving the emergency situation.
WARNING
Fasten the wheel cap cor-
rectly to prevent the wheel
from coming free in motion. Never
tamper with the inflation valve. Nev-
er place tools between the rim and
tyre. Check the tyre and space-saver
spare wheel pressure regularly. The
tyre inflation pressure is shown in the
“Technical specifications” chapter.
WARNINGPlease note:
❒the jack cannot be repaired. If it breaks
it must be replaced with a new jack;
❒no tool other than its cranking device
may be fitted on the jack.
To change a wheel proceed as follows:
❒Stop the car in a position that is not
dangerous for oncoming traffic where
you can change the wheel safely. The
ground should be flat and adequately
firm;
❒Turn the engine off and pull up the
handbrake;
❒Engage first gear or reverse;
❒Lift the luggage compartment panel
mat;
❒Loosen the fastener A-fig. 11;
❒Take the tool bag Band go to the
wheel to be replaced;
❒Take the space-saver spare wheel C;
❒If the car is fitted with alloy rims, re-
move the wheel hub with the screw-
driver provided levering in the groove
E-fig. 12, as shown in the figure;
133-160 idea GB 1 ed 10-07-2008 8:30 Pagina 141

142
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
❒Loosen the bolts on the wheel to be
replaced by about one turn with the
wrench provided E-fig. 12; if the car
is fitted with alloy rims, shake the car
to facilitate removing this rim from the
wheel hub;
❒Operate the device F-fig. 12and ex-
tend the jack until groove Gon the
jack fits correctly into ridge Hon the
body near sign I(at about 60 cm from
the front wheel centre or 80 cm from
the rear wheel centre);
fig. 12F0H0750m
❒Warn anybody nearby that the car is
about to be lifted. They must stay clear
and not touch the vehicle until it is
back on the ground;
❒Fit the handle L-fig. 14to operate the
jack and lift the car until the wheel to
be changed is several centimetres off
the ground;
❒For versions with wheel cap, remove
the wheel cap after unloosing the
three fastening bolts and finally un-
loose the fourth bolt and extract the
wheel.
❒Make sure the contact surfaces be-
tween spare wheel and hub are clean
so that the fastening bolts will not
come loose;
fig. 13F0H0751m
❒Fit the spare wheel making the holes
M-fig. 15coincide with the respective
centring pins N;
❒Using the wrench provided, fully tight-
en the four fastening bolts;
❒Turn the jack handle L-fig. 14to low-
er the car and remove the jack;
❒Use the wrench provided to fasten the
bolts completely in a criss-cross fash-
ion as shown in the figure.fig. 11F0H0161m
133-160 idea GB 1 ed 10-07-2008 8:30 Pagina 142