2008 FIAT FIORINO lock

133
SAFETY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARDAND CONTROLS
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
❒If at least 1.8 bar pressure is read, re-
store proper pressure (with engine
running and handbrake on) and restart.
❒Drive with the utmost care to the near-
est Fiat Dealership.FOR CHECKING AND
RESTORING PRESSURE ONLY
The compressor may also be used for
restoring pressure only. Release the quick
coupling and connect directly to the tyre
valve fig. 20; in this way, the cylinder will
not be connected to the compressor and
no sealant will be injected. CYLINDER REPLACEMENT
PROCEDURE
To replace the cylinder proceed as fol-
lows:
❒disconnect connection B-fig. 21;
❒turn the cylinder anticlockwise to raise
and replace it;
❒fit the new cylinder and turn it clock-
wise;
❒plug connection Binto the cylinder and
fit the transparent tube Ainto the
proper space.
Stop the vehicle if the pres-
sure has dropped below 1.8
bars. The automatic Fix & Go fast re-
pair kit cannot work properly be-
cause the tyre is excessively damaged.
Go to a Fiat Dealership.
WARNING
Remember to inform the
workshop that the tyre has
been treated with a fast repair kit.
Give the instruction booklet to the
tyre repair workshop personnel.
WARNING
fig. 20F0T192mfig. 21F0T0132m
123-154 Fiorino GB 2ed 8-02-2008 15:27 Pagina 133

135
SAFETY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARDAND CONTROLS
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
BULB TYPES fig. 22
Various types of bulbs are fitted to your
vehicle.
A All glass bulb: clipped into place. Pull
to extract.
B Bayonet bulbs: to remove this type
of bulb from its holder, press the bulb
and turn it anticlockwise.
fig. 22FF0T0022m
C Cylindrical bulbs: release from the
contacts to extract.
D Halogen bulbs: release the fastening
clip from the corresponding seat to re-
move the bulb.
E Halogen bulbs: release the fastening
clip from the corresponding seat to re-
move the bulb.
123-154 Fiorino GB 2ed 8-02-2008 15:27 Pagina 135

137
SAFETY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARDAND CONTROLS
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
IF AN EXTERIOR
LIGHT BURNS OUT
For the type of bulb and power rating, see
“When needing to change a bulb”.
FRONT LIGHT CLUSTERS fig. 23
The front light clusters contain sidelight,
dipped beam, main beam and direction in-
dicator bulbs.
The bulbs are arranged inside the light
cluster as follows:
Aside/taillights and main/low beam lights;
Bdirection indicators.SIDE/TAILLIGHTS
To change the bulb, proceed as follows:
❒remove the protection lid A-fig. 23;
❒turn the bulb holder anticlockwise A-
fig. 24and pull it out;❒remove the bulb Band replace it;
❒install the new bulb: fit the bulb back
in position A-fig. 24and put the pro-
tection lid A-fig. 23back.
fig. 23F0T0093mfig. 24F0T0094m
123-154 Fiorino GB 2ed 8-02-2008 15:27 Pagina 137

138
SAFETY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARDAND CONTROLS
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
DIPPED BEAM HEADLIGHTS/
MAIN BEAM HEADLIGHTS
To change the bulb (double filament), pro-
ceed as follows:
❒remove the protection lid A-fig. 23;
❒release the bulb stop clip as shown by
the arrows fig. 23;
❒remove the bulb A-fig. 25from con-
nector Band replace it;
❒fit the new bulb on the connector B.
Then, make sure that the profile of the
metal part matches the grooves on the
headlight bulb support;
❒close the bulb stop clip and reinstall the
protection lid A-fig. 23;DIRECTION INDICATORS
Front indicators
To change the bulb, proceed as follows:
❒turn the protection lid B-fig. 23anti-
clockwise;
❒remove the bulb A-fig. 26and replace
it;
❒reinstall the protection lid B.
fig. 25F0T0095mfig. 26F0T0096m
123-154 Fiorino GB 2ed 8-02-2008 15:27 Pagina 138

139
SAFETY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARDAND CONTROLS
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
Side indicators
To change the bulb, proceed as follows:
❒push the lens A-fig. 27to compress
the internal catch B-fig. 28. Then, pull
the unit outwards;
❒turn the bulb holder C anticlockwise,
remove the snap-fitted bulb Dand re-
place it;
fig. 27F0T0097mfig. 28F0T0098m
❒refit the bulb holder Cin the lens by
turning it clockwise;
❒refit the unit making sure the catch
clicks into place B.FOG LIGHTS (where provided)
IMPORTANT To replace the front fog
lights you must contact the Fiat Dealership.
123-154 Fiorino GB 2ed 8-02-2008 15:27 Pagina 139

141
SAFETY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARDAND CONTROLS
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
3rdSTOP LIGHTS fig. 33
To replace the 3
rdstop lights you must
contact the Fiat Dealership.
fig. 33F0T0103mfig. 34F0T0104mfig. 35F0T0105m
PLATE LIGHTS
To replace the bulbs A-fig. 34proceed as
follows:
❒pull the tongues indicated by the arrows
and remove the bulb holders;
❒turn the bulb holder B-fig. 35clock-
wise and take the bulb Cout.
123-154 Fiorino GB 2ed 8-02-2008 15:27 Pagina 141

142
SAFETY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARDAND CONTROLS
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
IF THE INTERIOR
LIGHT BURNS OUT
For the type of bulb and power rating, see
“When needing to change a bulb”.
FRONT CEILING LIGHT
Front ceiling light with
movable lens
To replace the bulbs proceed as follows:
❒remove the ceiling light A-fig. 36lev-
ering in the points shown by the ar-
rows;
❒open the lid B-fig. 37as indicated;❒replace bulb C-fig. 38releasing it from
the side contacts. Then, insert the new
bulb making sure it is correctly clamped
between the contacts;
❒close the lid and secure the ceiling light
in its housing locking it properly.
fig. 36F0T0106mfig. 37F0T0023m
fig. 38F0T0024m
123-154 Fiorino GB 2ed 8-02-2008 15:27 Pagina 142

143
SAFETY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARDAND CONTROLS
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
Ceiling light with spot lights
(where provided)
To replace the bulbs proceed as follows:
❒work in the points shown by the ar-
rows and remove light A-fig. 39;
❒open the protection door B-fig. 40;
❒replace bulbs Cafter releasing them
from the side contacts; make sure that
new bulbs are correctly clamped be-
tween contacts;
❒close the door B-fig. 40and secure the
ceiling light A-fig. 39in its housing lock-
ing it properly.REAR CEILING LIGHT
Cargo versions
To change the bulb, proceed as follows:
❒remove the ceiling light A-fig. 41lev-
ering in the points shown by the ar-
rows;
❒open the lid B-fig. 42as indicated;
fig. 39F0T0143mfig. 40F0T0144mfig. 41F0T0107m
fig. 42F0T0023m
123-154 Fiorino GB 2ed 8-02-2008 15:27 Pagina 143