2008 FIAT DUCATO wheel bolts

159
WARNING
LIGHTS AND
MESSAGES
VEHICLE
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE
VEHICLE
IN AN
EMERGENCY
IMPORTANT Never connect the negative
terminals of the two batteries directly:
sparks could ignite explosive gas released
from the battery. If the auxiliary battery is
installed on another vehicle, avoid any
metal parts on the latter and the vehicle
with the flat battery from accidentally
coming into contact.
BUMP STARTING
Never jump start the engine by pushing,
towing or driving downhill. This could
cause a flow of fuel into the catalytic con-
verter and damage it beyond repair.
IMPORTANT Remember that the brake
servo and the power steering system are
not activated until the engine is started, a
greater effort will therefore be required
to press the brake pedal or turn the steer-
ing wheel.CHANGING
A WHEEL
GENERAL INSTRUCTIONS
To chage a wheel and the use the jack and
spare wheel correctly, observe some of
the precautions listed below.
Signal that the vehicle is sta-
tionary in accordance with
the following legal requirements:
hazard warning lights, emergency
warning triangle, etc. It is advisable
for the people in the vehicle to get
out, especially if the vehicle is heavi-
ly laden, and wait until the repair is
carried out, well away from any dan-
gerous traffic. Apply the handbrake
WARNING
The spare wheel is specific
for your vehicle. Therefore,
it must not be used on vehicles of a
different model. Do not use spare
wheels of different models on your ve-
hicle. The wheel bolts are specific for
your vehicle. Do not use them on ve-
hicles of different models. Do not use
bolts of different models on your ve-
hicle.
WARNING
Repair and refit the wheel
changed as soon as possible.
Do not apply grease to the bolt
threads before assembly: the bolts
could come loose unexpectedly.
WARNING

161
WARNING
LIGHTS AND
MESSAGES
VEHICLE
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE
VEHICLE
IN AN
EMERGENCY
❒for versions with alloy wheels, remo-
ve the press-fitted hub cap;
❒loosen the bolts on the wheel to be
replaced by one turn;
❒turn the ring nut to extend the jack
partly;
❒position the jack near the lift support
closest to the wheel to be changed at
the points shown in fig. 3. For short
wheelbase versions with a retractablefootboard, the jack must be positio-
ned at the lift point shown in fig. 4ali-
gned (45°) so that it does not interfe-
re with the retractable footboard;
❒warn anybody nearby that the vehicle
is about to be lifted. They must stay
clear and not touch the vehicle until
it is back on the ground. Lift the vehi-
cle.After lifting the vehicle:
❒for all versions, when gaining access via
the vehicle’s right rear wheel arch fig.
5a, adjust the screw for the wheel re-
taining device, using the spanner pro-
vided with the extension/adaptor A-
fig. 5b;
❒introduce the wheel wrench and turn
anti-clockwise to allow the lowering
of the spare wheel.
❒continue turning anti-clockwise until
the stop point, signalled by the harde-
ning of the manoeuvre or a click from
the clutch present in the device.
fig. 4F0N0194m
fig. 6F0N0165m
The device should only be
operated by hand, without
using any type of tool other than the
crank provided like pneumatic or
electrical screwers.
WARNING
❒use the wheel dismantling spanner to
remove the wheel from the vehicle
fig. 6;
❒undo the retaining knob D - fig. 7 and
release the wheel releasing the sup-
port E.
fig. 5aF0N0390m
fig. 5b
A
F0N0391m

162
WARNING
LIGHTS AND
MESSAGES
VEHICLE
MAINTENANCE
TECHNICAL
SPECIFICATIONS
IINDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE
VEHICLE
IN AN
EMERGENCY
❒fully tighten the bolts, passing alterna-
tely from one bolt to the opposite
one, following the order illustrated in
fig. 9a.
When the operation is over:
❒take the wheel replaced, refit it on the
support E-fig. 7and tighten the knob
D-fig. 7;
❒introduce the wheel wrench on the
bolt fig. 5a-5band turn it clockwise
to allow the spare wheel to be raised
until it is resting completely on the
housing under the floor pan; Even the moving jack components (bolt
and joints) could cause injury: do not
touch them. If you come into contact with
lubricating grease, clean yourself thor-
oughly;
❒fully unscrew the bolts using the span-
ner F-fig. 8and extract the wheel;
❒fit the spare wheel, making sure that
the openings G-fig. 9aare aligned
with the pins H. When fitting the
spare wheel, ensure that the wheel
support surfaces are clean and free of
impurities that could later cause the
bolts to loosen;
❒tighten the 5 fastening bolts;
❒use the wheel removal wrench to
lower the vehicle and extract the jack;
At the end of the operation
of raising/locking the spare
wheel, the key must be extracted,
taking care not to turn it in the wrong
direction when trying to facilitate the
extraction of the actual key, to pre-
vent the attachment device from be-
ing released and the wheel assembly
not being securely retained fig. 9b.
WARNING
For vehicles with alloy wheels, proceed as
follows:
– take the kit from the tool box;
– Fit the special plate A-fig. 9con the al-
loy wheel, fastening it using the bolts B-
fig. 9cprovided using the spanner pro-
vided;
– reattach the wheel to the support turn-
ing it until the end of the slot (as illus-
trated in fig. 9d) and tighten the knob
D-fig. 9d;
fig. 8F0N0167mfig. 9aF0N0168mfig. 7F0N0370m