2008 FIAT DUCATO 250 brake

3
READY TO START
MANUAL MODE
IMPORTANT For correct use of the sys-
tem, it is advisable to use your right foot
only to operate the pedal.
❒Press the brake pedal.
❒Start the engine.
❒Push the gear lever towards + (shift up)
fig. 1to engage first gear (if starting
from Nor Rsimply move the lever to
the central position) or R fig. 2to en-
gage reverse.
❒Release the brake pedal and press the
accelerator pedal.
❒When driving, push the gear lever to-
wards (+)fig. 1to engage a higher gear
or towards (–)fig. 1to engage a low-
er gear.
COMFORT-MATIC
GEARBOX
Your vehicle is equipped with an elec-
tronically controlled manual gearbox
known as the “COMFORT-MATIC” that
is able to operate in two modes: MAN-
UALand AUTO.
The gearbox consists of a conventional
manual transmission equipped with a lever
A-fig. 1, to which has been added an elec-
tronically-controlled hydraulic device that
controls the clutch and gear shifts auto-
matically.
fig. 1F0N0350m
fig. 2F0N0351m
604.39.084 Ducato MTA Confort GB 31-03-2008 16:10 Pagina 3

4
AUTOMATIC MODE
IMPORTANT For correct use of the sys-
tem, it is advisable to use your right foot
only to operate the pedal.
❒Press the brake pedal.
❒Start the engine.
❒Push the gear lever to A/M fig. 3, to
engage automatic mode +(higher gear)
fig. 1to engage the first gear, if start-
ing from Nor Rmove the lever to cen-
tral position R fig. 2to engage reverse.
❒Release the brake pedal and press the
accelerator pedal.
OPERATING MODE
The gearbox can operate in two operat-
ing modes:
❒the first is manual (MANUAL), where
the driver decides directly when to shift
gear;
❒the second fully automatic (AUTO),
where the system decides when to shift
gear. This mode allows you to use the
UPfunction (steep road function),
which allows you to shift gears at high-
er speeds to allow you to drive up very
steep roads easily with any load. To en-
gage this function, press the UPbut-
ton - fig. 4between the controls on the
dashboard. Select the gear and the op-
erating mode MANUALor AUTO)
by operating the control lever at any
speed.
fig. 3F0N0352mfig. 4F0N0353m
CONTROL LEVER
Control lever A-fig. 1, on the central
tunnel is a floating multistable lever, i.e. it
can take up three stable positions and
three unstable positions.
The three stable positions correspond to
neutral N-fig. 2, reverse R-fig. 2and the
central position between the unstable po-
sitions (–) and (+)fig. 1.
The unstable positions, i.e. positions left
by the lever as soon as it is released, are
upshift request (+), downshift request (–)
and automatic mode request (A/M)
fig. 3.
604.39.084 Ducato MTA Confort GB 31-03-2008 16:10 Pagina 4

5
The system is returned to manual mode
by returning the lever to A/Mposition.
With the vehicle at a standstill and the key
out, the lever may be moved with/without
the brake pedal pressed. The system does
not carry out any action after the lever has
been shifted and remains in the gear
stored before the key was removed.
IMPORTANT With the engine running, a
buzzer sounds to indicate errors between
the lever position and the gear effectively
engaged until the inconsistency is resolved.MANUAL OPERATION
(MANUAL)
In this operating mode, the driver is re-
sponsible for choosing the best gear ra-
tio to engage, depending on vehicle ser-
vice conditions.
Proceed as follows to shift gear:
❒shift the lever to (+) position fig. 1to
engage a higher gear;
or
❒shift the lever to (–) position fig. 1to
engage a lower gear.
The accelerator pedal need not be re-
leased during the gear change.
The system will not allow the gear change
if the gear shift request could impair cor-
rect operation of the engine and gearbox.
In this case, the system will notify the dri-
ver that it is not possible to change gear
by displaying a dedicated message on the
reconfigurable multifunction display (see
“Warning lights and messages” paragraph),
accompanied by a buzzer.
The system will shift down through the
gears automatically when the engine is
idling (e.g. during deceleration).Avoid keeping your hand on
the lever when you are not re-
questing a gear shift or an
Auto/Manual mode change.
AUTOMATIC OPERATION
(AUTO)
to engage/release automatic mode (AU-
TO) press the lever to A/M positionfig.
3; activation is indicated by the message
AUTO fig. 5and the gear engaged ap-
pearing on the reconfigurable multifunc-
tion display.
fig. 5F0N0354m
604.39.084 Ducato MTA Confort GB 31-03-2008 16:10 Pagina 5

7
When the UPfunction is activated the
(green) warning light
0in the instru-
ment panel comes on together with a con-
firmation message in the reconfigurable
multifunction display.
IMPORTANT If the display does not show
the gear engaged after 10 seconds with the
ignition key on MAR, turn the ignition to
STOP, wait for the display to turn off and
then repeat the manoeuvre. If the prob-
lem persists, contact the Fiat Dealer-
ship.ENGINE STARTING
The system permits engine start-up with
a gear engaged and also with the gearbox
in neutral (N); the brake pedal must al-
ways be pressed with the gear engaged.
It is advisable to place the gear lever in
neutral (N) before starting the engine.
After start-up:
❒the gearbox automatically engages neu-
tral (N)
❒the lever remains in the same position
as the last time the engine was turned
off
❒the reconfigurable multifunction display
shows the message (N) and an acoustic
signal indicates any inconsistency be-
tween lever position and the gear en-
gaged
❒the gears that may be engaged are 1st,
2ndor reverse (R), with the brake ped-
al pressed.IMPORTANT If start-up is requested with
the gearbox is a position other than Nand
without the brake pedal pressed, the re-
configurable multifunction display shows a
dedicated message see “Warning lights
and messages”). In this case, repeat the
start-up manoeuvre, pressing the brake
pedal.
IMPORTANT If start-up is requested with
the gearbox faulty, run the “Delayed start-
up” procedure (see also associated mes-
sages): hold the key on AVVposition for
at least 7 seconds with the brake depressed
and the engine will start. The system will
remain in recovery mode (maximum speed
permitted: 3
rd, Auto mode not available).
If the engine does not start, contact a Fiat
dealership.
IMPORTANT When the driver’s door is
opened, the system activates the auto-
matic part to prepare it for subsequent en-
gine start-up.
If the engine does not start
with the gear engaged, a po-
tentially hazardous situation
because the gearbox has au-
tomatically shifted to neutral is indi-
cated by a buzzer.
fig. 6F0N0354m
604.39.084 Ducato MTA Confort GB 31-03-2008 16:10 Pagina 7

8
DRIVING OFF IN THE VEHICLE
Driving off in the vehicle, take-off, is per-
mitted in 1
stgear, 2nd gear (recommend-
ed on road surfaces with poor grip) and
reverse (R).
To engage 1
stgear
❒press the brake pedal;
❒with the lever in (N) or (R) shift the
lever to central position;
❒with the lever already in central posi-
tion, move the lever toward +(higher
gear) fig. 1;
❒release the brake pedal and press the
accelerator pedal.To engage 2
ndgear
❒press the brake pedal;
❒with the lever in (N) or (R) fig. 2
move the lever to central position and
then towards +(higher gear) fig. 1;
❒with the lever already in central posi-
tion, move the lever twice toward +
(higher gear) fig. 1;
❒release the brake pedal and press the
accelerator pedal.
To engage reverse (R)
❒press the brake pedal;
IMPORTANT If the vehicle is moving, the
request is accepted and carried out if the
vehicle speed is less than 3 km/h within 1.5
seconds of the request: if the request is
not implemented, the system will maintain
the gear engaged or if vehicle speed drops
below 10 km/h it will put the gearbox in
neutral (N) and the manoeuvre must then
be repeated.
❒Shift the lever to (R) fig. 2;
❒release the brake pedal and press the
accelerator pedal.BUZZER WARNINGS
For safety reasons, a buzzer warning
sounds when the vehicle is parked with
the gearbox in neutral (N) (the warning
sounds when the ignition key is turned to
STOP).
With the vehicle at a standstill, engine run-
ning and (1), (2) or (R) gear engaged, the
system turns on the buzzer and automat-
ically shifts the gearbox to neutral (N)
when:
❒the accelerator and/or brake pedals are
not operated for at least 3 minutes;
❒the brake pedal is pressed for longer
than 10 minutes;
❒the driver’s door is opened and the ac-
celerator and brake are not operated
for at least 1.5 seconds;
❒a fault has been detected in the gear-
box.
604.39.084 Ducato MTA Confort GB 31-03-2008 16:10 Pagina 8

9
PARKING THE VEHICLE
To park safely, it is essential to engage 1
st
gear or reverse (R) gear with your foot
on the brake pedal. If parking on a slope,
operate the brake pedal. It is also essen-
tial to wait until the gear engaged disap-
pears from the reconfigurable multifunc-
tion display before releasing the brake
pedal.
IMPORTANT NEVERleave your vehicle
with the gearbox in neutral (N).GENERAL WARNINGS❒With the vehicle at a standstill and a
gear engaged, keep the brake pedal
pressed until you decide to set off.
Then release the brake and accelerate
gradually;
❒when parked for long periods with the
engine running, it is advisable to keep
the gearbox in (N);
❒to safeguard clutch efficiency, do not
use the accelerator to keep the vehi-
cle at a standstill (e.g.: parking on a hill);
the clutch could be damaged by over-
heating. Use the brake pedal instead
and operate the accelerator only when
you are ready to set off;
❒use second gear only when you need
more control of take-off during ma-
noeuvres on surfaces with low grip;
❒if, with reverse (R) engaged, you need
to engage first speed or vice versa, on-
ly change gear when the vehicle has
come to a stop and the brake pedal is
pressed;;
❒although very inadvisable, if the vehi-
cle is unexpectedly allowed to roll
downhill with the gearbox in neutral
(N) the system will automatically en-
gage the gear best suited to vehicle
speed when a gear shift is requested to
allow drive to be correctly transmitted
to the wheels;
❒If necessary, with the engine off, it is pos-
sible to engage 1st, Ror Nwith the key
in MARposition and the brake pressed.
In this case, gear shifts must be made al-
lowing at least 5 minutes to elapse be-
tween one gear shift and the next to
safeguard the operation of the hydraulic
system and the pump in particular;
❒during hill st arts, accelerate gradually
but fully immediately after releasing the
handbrake or brake pedal to allow the
engine to increase its rpm to a greater
extent and overcome higher gradients
with more torque.
604.39.084 Ducato MTA Confort GB 31-03-2008 16:10 Pagina 9

11
AUTOMATIC MODE
NOT AVAILABLE
The message appears on the reconfig-
urable multifunction display when it is not
possible to select AUTOmode with the
engine running.CLUTCH OVERHEATING
The message appears on the reconfig-
urable multifunction display together with
a buzzer when the clutch overheats.
In this situation, limit take-off and gear
shifts or if necessary park (turning off the
engine) until conditions are optimum.PRESS BRAKE PEDAL -
DELAYED START-UP
The reconfigurable multifunction display
shows these messages alternately and in
sequence together with an warning buzzer
when the system does not recognise the
brake pedal to be operational during a
starting attempt.
In this situation, keep the key on AVVfor
at least 7 seconds with the brake pressed:
the engine start. The system will be in re-
covery mode (maximum speed permitted:
3
rd).
IMPORTANT Messages are displayed on-
ly if start-up takes place in a gear other
than neutral (N). Contact a Fiat Dealership if
the message remains on the
reconfigurable multifunction
display.
If the message still appears on
the reconfigurable multifunc-
tion display, contact a Fiat
Dealership.
To safeguard clutch efficien-
cy, do not use the accelerator
to keep the vehicle at a stand-
still (e.g.: parking on a hill);
the clutch could be damaged by over-
heating. Use the brake pedal instead
and operate the accelerator only when
you are ready to set off;
Contact a Fiat Dealership if
the messages remain on the
reconfigurable multifunction
display.
604.39.084 Ducato MTA Confort GB 31-03-2008 16:10 Pagina 11

12
GEAR NOT AVAILABLE
This message appears on the reconfig-
urable multifunction display together with
a warning buzzer in the following cases:
❒when it is not possible to change gear
due to a fault in the system;
or
❒when, due a fault in the system, is is on-
ly possible to engage 1st(1), 2nd(2), 3rd
(3) or reverse (R).MANOEUVRE NOT PERMITTED
The message appears on the reconfig-
urable multifunction display together with
a warning buzzer when the system will not
accept a gear change via the control lever
because certain conditions required for
acceptance of the gear change are missing.
PRESS BRAKE PEDAL
AND REPEAT MANOEUVRE
The message appears on the reconfig-
urable multifunction display accompanied,
in some cases, by a warning buzzer for
safety reasons if you attempt to change
gear with the vehicle parked without pre-
viously pressing the brake pedal.PLACE GEAR LEVER IN N
(neutral)
This message appears on the reconfig-
urable multifunction display together with
a warning buzzer when the system asks
the driver to perform the manoeuvre.
When the gearbox is shifted to (N) the
message on the display should go off.
Contact a Fiat Dealership if
the message remains on the
reconfigurable multifunction
display.Contact a Fiat Dealership if
the message remains on the
reconfigurable multifunction
display.
Contact a Fiat Dealership if
the message remains on the
reconfigurable multifunction
display.
604.39.084 Ducato MTA Confort GB 31-03-2008 16:10 Pagina 12