2008 FIAT DOBLO Ac unit

6GETTING TO KNOW YOUR VEHICLE
SYMBOLS
Special coloured labels have been at-
tached near or actually on some of the
components of your Fiat Doblò. These
labels bear symbols that remind you of
the precautions to be taken as regards
that particular component.
Plate A-fig. 1summarising the sym-
bols used can be found under the bon-
net.
THE FIAT CODE
SYSTEM
To further protect your vehicle from
theft, it has been fitted with an engine
immobilising system (Fiat CODE sys-
tem) which is automatically activated
when the ignition key is removed.
An electronic device, in fact, is fitted
in each ignition key grip. The device
transmits a radio-frequency signal
when the engine is started through a
special aerial built into the ignition
switch. The modulate signal, which
changes each time the engine is start-
ed, is the password by means of which
the control unit recognises the key
and enables to start the engine.KEYS fig. 2
The following keys are provided with
the vehicle:
– two keys Awhen the vehicle is not
equipped with remote control;
– key Aand key Bwhen the vehicle
is equipped with door lock remote
control.
– Key Ais the key that is used nor-
mally. It will:
– start the engine;
– lock/unlock front doors;
G G
E E
T T
T T
I I
N N
G G
T T
O O
K K
N N
O O
W W
Y Y
O O
U U
R R
V V
E E
H H
I I
C C C
L L
E E
fig. 1
F0A0001b
fig. 2
F0A0700b
001-105 Doblo GB 16-12-2008 14:22 Pagina 6

7GETTING TO KNOW YOUR VEHICLE
– lock/unlock the rear doors or the
tailgate;
– lock/unlock the side doors, Cargo
versions only;
– deactivate the passenger’s airbag.
The key B, with a built-in remote
control, has the same functions as key
Ain vehicles with door lock remote
control.
The CODE card fig. 3is also sup-
plied with the keys and bears the fol-
lowing:
a- the electronic code to be used for
emergency starting (see “Emergency
start-up” in section “In an emer-
gency”);b- the mechanical key code to be
given to the Fiat Dealershipwhen
ordering duplicate keys.
Keep the CODE card in a safe place.
Make sure you have the electronic
code of the CODE card with you at all
times in the event you have to per-
form an emergency start-up.
OPERATION
Each time the ignition key is turned
to STOP, or PARK, the protection
system will automatically immobilise
the engine.
When the key is turned to MARto
start the engine:
1)if the code is recognised the ¢
(Y) warning light on the instrument
panel will flash briefly; this means the
protection system has recognised the
key code and deactivates the immo-
biliser, turn the key to AVV, and the
engine will start.
2)If the warning light ¢(Y) stays
on, the code was not recognised. In
this case, turn the key to STOPand
then back to MAR. If the engine re-mains immobilised, try with the oth-
er key provided.
If you are still unable to start the en-
gine, use the emergency starting pro-
cedure (see “In an emergency”) and
take your vehicle to the nearest Fiat
Dealership.
When the vehicle is travelling and the
key is at MAR:
1)if the warning light ¢(Y) comes
on while the vehicle is moving, this
means that the system is running a self-
test (e.g. due to a voltage drop).
2)if the warning light ¢(Y) flash-
es, the vehicle is not protected by the
engine immobiliser. Contact a Fiat
Dealershipimmediately and get them
to store the codes of all the keys in the
memory.
IMPORTANT The electronic com-
ponents inside the key may be dam-
aged if the key is subjected to sharp
knocks.
IMPORTANTEach key provided
with the vehicle has its own code, dif-
ferent from all the others, which must
be stored in the memory of the sys-
tem control unit.
fig. 3
F0A0003b
001-105 Doblo GB 16-12-2008 14:22 Pagina 7

26GETTING TO KNOW YOUR VEHICLE
WARNING LIGHT TEST
fig. 40
The following warning lights are test-
ed:
– handbrake on/low brake fluid lev-
el;
– ABS and EBD system (where pro-
vided);
This tests are carried out automati-
cally when turning the ignition key to
MARand during normal operation
when a fault is found. At the end of the
initial check, the display will show fail-
ures, if any (through one or more
warning lights) by the wording “LEd
Error” flashing for about 10 seconds.DIGITAL DISPLAY
“STANDARD” SCREEN fig. 38
The standard screen shows the fol-
lowing indications:
A- Headlight aiming position display
(with dipped beam headlights on).
B- Clock (always displayed, also with
key removed and front doors closed).
C- Odometer (km or miles cov-
ered).CONTROL BUTTONS fig. 39
A- Clock.
CLOCK fig. 39
To adjust the clock press button A.
The clock will advance by one unit
each time the button is pressed. Press
the button and hold it down for a few
seconds to rapidly advance the time
automatically. When the clock draws
near to the correct time, release the
button and complete the regulation
manually.
fig. 39
F0A0229b
fig. 40
F0A0503b
fig. 38
F0A0502b
001-105 Doblo GB 16-12-2008 14:22 Pagina 26

27GETTING TO KNOW YOUR VEHICLE
MULTIFUNCTION
DISPLAY
STANDARD SCREEN fig. 41
The standard screen shows the fol-
lowing indications:
A- Headlight aiming position display
(with dipped beam headlights on).
B- Clock.
C- Odometer (km or miles cov-
ered).
Note With ignition key removed,
when opening one of the front doors
the display comes on showing the
clock and km/mi covered for a few
seconds.CLOCK fig. 42
To adjust the clock press button A
to increase minutes and button Bto
decrease minutes. The clock will ad-
vance by one unit each time the but-
ton is pressed. Press the button and
hold it down for a few seconds to
rapidly advance the time automatical-
ly. When the clock draws near to the
correct time, release the button and
complete the regulation manually.WARNING LIGHT TEST
fig. 43
The following warning lights are test-
ed:
– handbrake on/low brake fluid lev-
el;
– ABS and EBD system (where pro-
vided);
This tests are carried out automati-
cally when turning the ignition key to
MARand during normal operation
when a fault is found. At the end of the
initial check, the display will show fail-
ures, if any (through one or more
warning lights) by the wording LEd Err
flashing for about 10 seconds.
fig. 41
F0A0331b
fig. 42
F0A0340b
fig. 43
F0A0333b
001-105 Doblo GB 16-12-2008 14:22 Pagina 27

30GETTING TO KNOW YOUR VEHICLE
Day
Year
MODE
briefly
press but-
ton
Month
Deutsch
Português
English
Español
Français
Italiano
Nederland
Polski Example:
LANG. SERVICEEXIT MENUTRIP B
SET TIME
CLOCK MODE
SET DATE
AUTOCLOSE
DIST. UNIT
CONS.
TEMP. UNIT BUTTON VOL.
BUZZER VOL.SPEED
BEEP
Example:
+
– +
–
– +
+
–
–
+
+–
––
++++
–––
++
– –+ +
–MODE
briefly
press
button
Briefly press buttonMODEto start surfing from the
standard screen. To surf the menu use buttons +or –.
NoteFor safety reasons, when the vehicle is running,
it is possible to access only the reduced menu (for set-
ting the “Speed Beep”). When the vehicle is stationary
access to the whole menu is enabled. On vehicles
equipped with Connect Nav+ many functions are dis-
played on the navigator display.
F0A0505g
Türkçe
001-105 Doblo GB 16-12-2008 14:22 Pagina 30

31GETTING TO KNOW YOUR VEHICLE
– briefly press button MODEto go
back to the menu screen or press the
button for long to go back to the stan-
dard screen without storing settings.
To cancel the setting, proceed as fol-
lows:
– briefly press button MODE: (On)
will flash on the display;
– press button –: (Off) will flash on
the display;
– briefly press button MODEto go
back to the menu screen or press the
button for long to go back to the stan-
dard screen without storing settings.
Trip B On/Off (Trip B)
Through this option it is possible to
activate (On) or deactivate (Off) the
Trip B (partial trip). Speed limit (Speed Beep)
With this function it is possible to set
the vehicle speed limit (km/h or mph),
when this limit is exceeded the driver
is immediately alerted (see section
“Warning lights and messages”).
To set the speed limit, proceed as
follows:
– briefly press button MODE: (Off)
will flash on the display;
– press button +: (On) will flash on
the display;
– briefly press button MODEand
then + or – to set the required speed
(during setting the value flashes).
NoteThe possible setting is be-
tween 30 and 250 km/h, or between
20 and 155 mph depending on the unit
set previously (see “Distance unit
(Dist. Unit)” paragraph described lat-
er. Every press on button +/ –in-
creases/decreases by 5 units. Keeping
the button +/ –pressed obtains the
automatic fast increase or decrease.
When you are near the required set-
ting complete adjustment by single
presses.For further details see paragraph
“Trip computer”.
For activation / deactivation, proceed
as follows:
– briefly press button MODE: (On)
or (Off) will flash on the display (ac-
cording to previous setting);
– press button +or –for setting;
– briefly press button MODEto go
back to the menu screen or press the
button for long to go back to the stan-
dard screen without storing settings.
Set clock (Set clock)
This function enables to set the
clock.
To set the clock (hours - minutes)
proceed as follows:
– briefly press button MODE:
“hours” will flash on the display;
001-105 Doblo GB 16-12-2008 14:22 Pagina 31

32GETTING TO KNOW YOUR VEHICLE
– press button +or –for setting;
– briefly press button MODE: “min-
utes” will flash on the display;
– press button +or –for setting.
NoteEvery press on the button +
or –increases/decreases by one unit.
Keeping the button pressed obtains
automatic fast increase/decrease.
When you are near the required set-
ting complete adjustment by single
presses.
– briefly press button MODEto go
back to the menu screen or press the
button for long to go back to the stan-
dard screen without storing settings.
Clock mode (Clck. Mode)
This function is used to set the clock
in the 12h (12 hours) or 24h (24
hours) mode.
For setting proceed as follows:
– briefly press button MODE12h or
24h will flash on the display (accord-
ing to previous setting);
– press button +or –for setting;– briefly press button MODEto go
back to the menu screen or press the
button for long to go back to the stan-
dard screen without storing settings.
Set date (Adjust Date)
This function enables to update the
date (year - month - day).
To correct the date proceed as fol-
lows:
– briefly press button MODE:
“year” will flash on the display;
– press button +or –for setting;
– briefly press button MODE:
“month” will flash on the display;
– press button +or –for setting;
– briefly press button MODE: “day”
will flash on the display;
– press button +or –for setting.NoteEvery press on the button +
or –increases/decreases by one unit.
Keeping the button pressed obtains
automatic fast increase/decrease.
When you are near the required set-
ting complete adjustment by single
presses.
– briefly press button MODEto go
back to the menu screen or press the
button for long to go back to the stan-
dard screen without storing settings.
001-105 Doblo GB 16-12-2008 14:22 Pagina 32

33GETTING TO KNOW YOUR VEHICLE
“Distance” unit (Dist. Unit)
With this function it is possible to set
the unit in km or mi.
To set the required unit proceed as
follows:
– briefly press button MODE: km or
mi will flash on the display (according
to previous setting);
– press button +or –for setting;
– briefly press button MODEto go
back to the menu screen or press the
button for long to go back to the stan-
dard screen without storing settings. Automatic door locking with
vehicle running (Autoclose)
(where provided)
When activated (On), this function
locks automatically the doors when
the vehicle speed exceeds 20 km/h.
To activate (On) or to deactivate
(Off) this function proceed as follows:
– briefly press button MODE: On or
Off will flash on the display (according
to previous setting);
– press button +or –for setting;
– briefly press button MODEto go
back to the menu screen or press the
button for long to go back to the stan-
dard screen without storing settings.“Consumption” unit (Cons.)
If the distance unit set is km (see pre-
vious paragraph) the display will enable
to set the fuel consumption unit (km/l
or l/100km).
If the distance unit set is mi (see pre-
vious paragraph) fuel consumption will
be displayed in mpg.
To set the required unit proceed as
follows:
– briefly press button MODE: km/l
or l/100km will flash on the display (ac-
cording to previous setting);
– press button +or –for setting;
– briefly press button MODEto go
back to the menu screen or press the
button for long to go back to the stan-
dard screen without storing settings.
001-105 Doblo GB 16-12-2008 14:22 Pagina 33