2008 FIAT CROMA spare wheel

164
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
For versions with alloy rims
❒Insert the wheel on the hub and, using
the wrench provided, tighten the
bolts.
❒Lower the car and remove the jack.
❒Using the wrench provided, fully tigh-
ten the bolts in the sequence shown
in fig. 10;
❒insert the logo holder by pressing on
the exterior side.When you have finished
❒Place the spacer.
❒Fit the jack partially open in its con-
tainer C-fig. 11forcing it lightly to
prevent it from vibrating when travel-
ling.
❒Put the tools back into their places in
the container. REFITTING THE STANDARD
WHEEL
Following the procedure described previ-
ously, raise the car and remove the spare
wheel.
For versions with steel rim
Proceed as follows:
❒make sure the contact surfaces be-
tween standard wheel and hub are
clean so that the fastening bolts will
not come loose;
❒fit the standard wheel by inserting the
first bolt for two threads into the hole
closest to the inflation valve;
❒using the wrench provided, tighten the
fastening bolts;
❒lower the car and remove the jack;
❒using the wrench provided, fully tight-
en the bolts in the sequence shown
previously;
❒fit the wheel cap making the groove
(on the wheel cap) coincide with the
inflation valve.
fig. 11F0L0219mfig. 10
25
3
1
4
F0L0368m
157-192 Croma TRW GB 10-11-2008 13:15 Pagina 164

165
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
❒Stow the container C-fig. 11, com-
plete with tools in the boot.
❒Place the space-saver spare wheel B-
fig. 12in the space provided for the
purpose inside the boot and secure it
with the clamping device A-fig. 12.
fig. 12F0L0218m
QUICK TYRE REPAIR
KIT FIX & GO
automatic
The quick tyre repair kit Fix & Go auto-
matic is located in the appropriate con-
tainer in the boot .
The quick tyre repair kit includes fig. 13:
❒bottle A containing sealer and fitted
with:
– filler hose B
– sticker Cwith caution “max. 80
km/h”, to be affixed in a visible posi-
tion for the driver (instrument panel)
after repairing the tyre
❒instruction brochure (see fig. 14), to
be used for prompt and proper use of
the quick repair kit and to be then
handed to the personnel charged with
handling the treated tyre
❒compressor Dincluding gauge and con-
nections
❒a pair of protection gloves located in
the side space of the compressor
❒adapters for inflating different elements.
Hand the instruction
brochure to the personnel
charged with treating the tyre re-
paired with the kit.
WARNING
In the event of a puncture
caused by foreign bodies, it is
possible to repair tyres show-
ing damages on the track or
shoulder up to max 4 mm diameter.
fig. 13F0L0393m
157-192 Croma TRW GB 10-11-2008 13:15 Pagina 165

210
WARNING
LIGHTS AND
MESSAGES
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
CAR
MAINTENANCE
In fact, since these devices continue ab-
sorbing energy even when the ignition key
is off, they gradually run down the battery.
The total intake of these systems (facto-
ry and after-market) must be less than 0,6
mA x Ah (of the battery) as shown in the
following table:
IMPORTANT NOTES
❒As far as possible, avoid sharp brak-
ing and screech starts, etc. Be careful
not to hit the kerb, potholes or oth-
er obstacles hard. Driving for long
stretches over bumpy roads can dam-
age the tyres;
❒Periodically check that the tyres have
no cuts in the side wall, abnormal
swelling or irregular tyre wear. If any
of these occur, have the car seen to at
a Fiat Dealership;
❒Avoid overloading the car when trav-
elling: this may cause serious damage
to the wheels and tyres;
Battery Maximum
admitted
stand-by intake
70 Ah 42 mA
90 Ah (*) 54 mA
(*) Versions fitted with alarm.
WHEELS AND TYRES
Check the pressure of each tyre, includ-
ing the spare, every two weeks and before
long journeys. The pressure should be
checked with the tyre rested and cold.
For the correct tyre inflation pressure, see
“Wheels” in “Technical specifications”
section.
Incorrect pressure causes abnormal tyre
wear:
Anormal pressure: tread evenly worn.
Blow pressure: tread particularly worn
at the edges.
Chigh pressure: tread particularly worn
in the centre.
Tyres must be replaced when the tread
wears down to 1.6 mm. In any case, com-
ply with the laws in the country where the
car is being driven.
fig. 17F0L0159m
193-216 Croma TRW GB 28-05-2008 15:19 Pagina 210

211
WARNING
LIGHTS AND
MESSAGES
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
CAR
MAINTENANCE
❒If a tyre is punctured, stop immediate-
ly and change it to avoid damage to the
tyre, the rim, suspensions and steering
system;
❒Tyres age even if they are not used
much. Cracks in the tread rubber are
a sign of ageing. In any case, if the tyres
have been on the car for over 6 years,
they should be checked by specialised
personnel, to see if they can still be
used. Also remember to check the
space-saver spare wheel;
❒In the case of replacement, always fit
new tyres, avoiding those of dubious
origin;
❒If a tyre is changed, also change the in-
flation valve;
❒To allow even wear between the front
and rear tyres, it is advisable to change
them over every 10-15 thousand kilo-
metres, keeping them on the same
side of the car so as to not reverse the
direction of rotation.
Remember that road holding
depends also on the correct
tyre inflating pressure.
WARNING
Do not cross switch the
tyres, moving them from the
right of the car to the left and vice
versa.
WARNING
If the pressure is too low the
tyre overheats and this can
cause it serious damage.
WARNING
Never submit alloy rims to
repainting treatments re-
quiring to use temperatures exceed-
ing 150°C since the mechanical prop-
erties of the wheels could be im-
paired.
WARNING
RUBBER HOSES
As far as the brake system and fuel rubber
hoses are concerned, carefully follow the
“Service schedule” in this section.
Indeed ozone, high temperatures and pro-
longed lack of fluid in the system may
cause hardening and cracking of the hoses,
with possible leaks. Careful control is
therefore necessary.
193-216 Croma TRW GB 28-05-2008 15:19 Pagina 211

SPACE-SAVER SPARE WHEEL
Pressed steel rim. Tubeless tyre.
WHEEL GEOMETRY
In order to guarantee the correct regula-
tion and stability of the vehicle, please con-
tact the Fiat Assistance Network.
UNDERSTANDING TYRE
MARKING fig. 4
Example: 205/55 R 16 91 V
205 = Nominal width (S, distance be-
tween sidewalls in mm).
55 = Percentage height/width ratio (H/
S).
R = Radial tyre.
16 = Rim diameter in inches (Ø).
91 = Load rating (capacity).
V = Maximum speed rating.WHEELS
RIMS AND TYRES
Pressed steel or alloy rims. Tubeless tyres
with radial carcass. The homologated tyres
are listed in the Log book.
IMPORTANT In the event of discrepan-
cies between the information provided on
this “Owner handbook” and the “Log
book”, consider the specifications shown
in the log book only.
Attaining to the prescribed size, to ensure
safety of the car in movement, it must be
fitted with tyres of the same make and
type on all wheels.
IMPORTANT Do not use inner tubes
with Tubeless tyres.
225
WARNING
LIGHTS AND
MESSAGES
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
fig. 4F0L0162m
217-242 Croma TRW GB 10-11-2008 13:16 Pagina 225

227
WARNING
LIGHTS AND
MESSAGES
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
VERSIONS RIMS (*) TYRES Space-saver spare wheel
Standard tyres Snow tyres Rim Tyre
1.86.5J x 16” - ET 36/41 205/55 R16 91V 205/55 R16 91 H (M+S)
6.5J x 16” - ET 36/41 215/55 R16 93W 215/55 R16 93 H (M+S) 4J 16 - 41115/70 R16 92M
7J x 17” - ET 36/41 215/50 R17 91W 215/50 R17 91 H (M+S)
2.2-2.2 a.t.6.5J x 16” - ET 36/41 205/55 R16 91V 205/55 R16 91 H (M+S)
6.5J x 16” - ET 36/41 215/55 R16 93W 215/55 R16 93 H (M+S)
7J x 17” - ET 36/41 215/50 R17 91W 215/50 R17 91 H (M+S)4J 16 - 41 115/70 R16 92M
7.5J x 18” - ET 36/41 225/45 R18 95W (Ô) 225/45 R18 95 H (M+S)
1.9 Multijet
8V6.5J x 16” - ET 36/41 205/55 R16 91V 205/55 R16 91 H (M+S)
1.9 Multijet 16V6.5J x 16” - ET 36/41 215/55 R16 93W 215/55 R16 93 H (M+S)1.9 Multijet 16Va.t.7J x 17” - ET 36/41 215/50 R17 91W 215/50 R17 91 H (M+S)4J 16 - 41 115/70 R16 92M7.5J x 18” - ET 36/41 225/45 R18 95W (Ô) 225/45 R18 95 H (M+S)
1.9 Multijet
8V6,5J x 16” - ET 36/41 205/55 R16 91V 205/55 R16 91 H (M+S) 4J 16-41115/70 R16 92Mpur-O2 (**)
2.4 Multijet 20Va.t.7J x 17” - ET 36/41 215/50 R17 95W 215/50 R17 91 H (M+S)
4J 16 - 41 115/70 R16 92M7.5J x 18” - ET 36/41 225/45 R18 95W (Ô) 225/45 R18 95 H (M+S)
(Ô) Tyres that cannot be fitted with snow chains
(*) ET 41 value referred to the rims available on the accessory line.
(**) Other size tyres are not type approved for these versions.
Note: rims with the same ET are to be used on the vehicle.
217-242 Croma TRW GB 10-11-2008 13:16 Pagina 227

228
WARNING
LIGHTS AND
MESSAGES
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
COLD TYRE INFLATION PRESSURE (bar)
Petrol versions
STANDARD TYRES Space-aver
Size Medium load Full load spare wheel
Front Rear Front Rear
205/55 R16 91V 2.4 2.4 2.7 2.6
1.8215/55 R16 93W 2.4 2.4 2.5 2.5 4.2
215/50 R17 91W 2.4 2.4 2.6 2.6
205/55 R16 91V 2.4 2.4 2.8 2.7
215/55 R16 93W 2.4 2.4 2.5 2.5
2.2
215/50 R17 91W 2.4 2.4 2.7 2.64.2
225/45 R18 95W 2.4 2.4 2.7 2.6
205/55 R16 91V 2.4 2.4 2.7 2.6
215/55 R16 93W 2.4 2.4 2.5 2.5
2.2 a.t.
215/50 R17 91W 2.4 2.4 2.6 2.54.2
225/45 R18 95W 2.4 2.4 2.6 2.5
Add +0.3 bar to the prescribed inflation pressure when the tyres are warm. Recheck pressure value with cold tyres.
With snow tyres, add +0.2 bar to the inflation pressure value prescribed for standard tyres.
If travelling at a speed higher than 160 km/h, inflate tyres at the values specified for fully laden conditions.
217-242 Croma TRW GB 10-11-2008 13:16 Pagina 228

229
WARNING
LIGHTS AND
MESSAGES
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
Multijet versions
STANDARD TYRES Space-saver
Size Medium load Full load spare wheel
Front Rear Front Rear
205/55 R16 91V 2.4 2.4 2.7 2.6
215/55 R16 93W 2.4 2.4 2.5 2.5
1.9 Multijet 8V215/50 R17 91W 2.4 2.4 2.6 2.54.2
225/45 R18 95W 2.4 2.4 2.6 2.5
205/55 R16 91V 2.4 2.4 2.8 2.7
215/55 R16 93W 2.4 2.4 2.5 2.5
1.9 Multijet 16V215/50 R17 91W 2.4 2.4 2.7 2.64.2
225/45 R18 95W 2.4 2.4 2.6 2.5
205/55 R16 91V 2.4 2.4 2.7 2.6
1.9 Multijet 16V215/55 R16 93W 2.4 2.4 2.5 2.5
a.t.
215/50 R17 91W 2.4 2.4 2.7 2.64.2
225/45 R18 95W 2.4 2.4 2.6 2.5
2.4 Multijet 20V215/50 R17 95W 2.6 2.5 2.9 2.7
4.2
a.t.
225/45 R18 95W 2.6 2.5 2.8 2.6
Add +0.3 bar to the prescribed inflation pressure when the tyres are warm. Recheck pressure value with cold tyres.
With snow tyres, add +0.2 bar to the inflation pressure value prescribed for standard tyres.
If travelling at a speed higher than 160 km/h, inflate tyres at the values specified for fully laden conditions.
217-242 Croma TRW GB 10-11-2008 13:16 Pagina 229