2008 DODGE NITRO lights

To Release the Steering Wheel Lock
Insert the key in the ignition and turn the wheel slightly
to the right or left to disengage the lock.
NOTE:If you turned the wheel to the right to engage
the lock, you must turn the wheel slightly to the right to
disengage it. If you turned the wheel to the left to engage
the lock, turn the wheel slightly to the left to disengage it.
SECURITY ALARM SYSTEM Ð IF EQUIPPED
This system monitors the vehicle doors, liftgate, and
ignition for unauthorized operation. When the alarm is
activated, the system provides both audible and visual
signals. The horn will sound repeatedly for three minutes
and the headlights and taillights will flash for an addi-
tional 15 minutes.
NOTE:The ªPanicº and ªSecurityº alarms are quite
different. Please take a moment to activate the ªPanicº
and the ªSecurityº modes to hear the differences in thehorn. In case one should go off in the future, you will
need to know which mode has been activated in order to
deactivate it.
To Arm the System:
Remove the keys from the ignition switch and exit the
vehicle. Lock the doors and liftgate by pressing the
power door lock switch or the Lock button on the remote
keyless entry transmitter. Close all doors. The ªVehicle
Security Alarm Indicator Lightº (located in the instru-
ment cluster) will flash rapidly for about 16 seconds to
signal that the system is arming. During this 16-second
pre-arm period, opening any door or the liftgate will
cancel the arming process. If the system arms success-
fully, the ªVehicle Security Alarm Indicator Lightº will
flash at a slower rate to indicate the alarm is set.
Manually locking the doors with the door lock plunger
(located on the inside of the doors) or the driver's door
key lock cylinder will not arm the system.
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

To Disarm the System:
Either press the Unlock button on the remote keyless
entry transmitter or insert a valid sentry key into the
ignition lock cylinder and turn the key to the ON
position.
The Security Alarm System is designed to protect your
vehicle; however, you can create conditions where the
system will give you a false alarm. If the previously
described arming sequence has occurred, the system will
arm regardless of whether you are inside or outside the
vehicle. If you remain inside the vehicle and open a door,
the alarm will sound. If this occurs, disarm the system.
Manually unlocking the doors with the door lock plunger
(located on the inside of the doors) or the driver's door
key lock cylinder will not disarm the system.
Tamper Alert
If something has triggered the alarm in your absence, the
horn will sound three times when you unlock the doors.
Check the vehicle for tampering.
ILLUMINATED ENTRY
The interior lights come on when you open any door.
They will remain on for about 30 seconds after all doors
are closed then fade to off.
The lights also will fade to off if you turn on the ignition
after you close all the doors.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19
2

REMOTE KEYLESS ENTRY
This system allows you to lock or unlock the doors and
liftgate or activate the panic alarm from distances up to
23 feet (7 meters) using your key fob. The key fob does
not need to be pointed at the vehicle to activate the
system.NOTE:²For the remote starting feature (if equipped), refer to
ªRemote Starting Systemº in this section.
²Your vehicle's key fob may have three or four buttons
depending on the optional features purchased with
your vehicle.
To Unlock the Doors and Liftgate
Press and release the ªUnlockº button on the key fob
once to unlock the driver's door, or twice to unlock all
doors and the liftgate. The parking lights will flash to
acknowledge the unlock signal. The illuminated entry
system will also turn on.
Remote Key Unlock, Driver Door/All Doors First
This feature lets you program the system to unlock either
the driver's door or all doors and the liftgate on the first
press of the ªUnlockº button on the key fob. To change
the current setting, proceed as follows:
Three Button Key Fob
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

On electronic vehicle information center (EVIC)
equipped vehicles, refer to ªRemote Key Unlock,º under
ªPersonal Settings (Customer Programmable Features),º
under ªElectronic Vehicle Information Center (EVIC)º in
Section 4 of this manual
On non-EVIC equipped vehicles, perform the following
steps:
1. Press and hold the ªLockº button on a programmed
(i.e. functional) key fob for at least 4 seconds, but not
longer than 10 seconds. Then, press and hold the ªUn-
lockº button while still holding the ªLockº button.
2. Release both buttons at the same time.
3. Test the feature from outside the vehicle by pressing
the ªLockº and ªUnlockº buttons on the key fob.
4. Repeat these steps if you want to return this feature to
its previous setting.NOTE:Pressing the ªLockº button on the key fob while
you are inside the vehicle will activate the Security
Alarm. Opening a door with the Security Alarm activated
will cause the alarm to sound. Press the ªUnlockº button
to deactivate the Security Alarm.
To Lock the Doors and Liftgate
Press and release the ªLockº button on the key fob to lock
all doors and the liftgate. If the ignition is OFF when the
doors are locked, the parking lights will flash once and
the horn will chirp once.
Sound Horn with Lock
This feature will cause the horn to chirp when the doors
are locked with the key fob. This feature can be turned on
or off. To change the current setting, proceed as follows:
²On electronic vehicle information center (EVIC)
equipped vehicles, refer to ªSound Horn with Lock,º
under ªPersonal Settings (Customer Programmable
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21
2

Features),º under ªElectronic Vehicle Information
Center (EVIC)º in Section 4 of this manual.
²On non-EVIC equipped vehicles, perform the follow-
ing steps:
1. Press the ªLockº button on a programmed (i.e. func-
tional) key fob for at least 4 seconds, but not longer than
10 seconds. Then, press the ªPanicº button while still
holding the ªLockº button.
2. Release both buttons at the same time.
3. Test the feature from outside the vehicle by pressing
the ªLockº button on the key fob.
4. Repeat these steps if you want to return this feature to
its previous setting.
NOTE:Pressing the ªLockº button on the key fob while
you are inside the vehicle will activate the SecurityAlarm. Opening a door with the Security Alarm activated
will cause the alarm to sound. Press the ªUnlockº button
to deactivate the Security Alarm.
Flash Lights with Lock
The feature will cause the parking lights to flash when
the doors are locked or unlocked with the key fob. This
feature can be turned on or turned off. To change the
current setting, proceed as follows:
²On electronic vehicle information center (EVIC)
equipped vehicles, refer to ªFlash Lights with Lock,º
under9Personal Settings (Customer Programmable
Features),º under ªElectronic Vehicle Information
Center (EVIC)º in Section 4 of this manual.
²On non-EVIC equipped vehicles, perform the follow-
ing steps:
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

1. Press and hold the ªUnlockº button on a programmed
(i.e. functional) key fob for at least 4 seconds, but not
longer than 10 seconds. Then, press and hold the ªLockº
button while still holding the ªUnlockº button.
2. Release both buttons at the same time.
3. Test the feature from outside the vehicle by pressing
the ªLockº and ªUnlockº buttons on the key fob.
4. Repeat these steps if you want to return this feature to
its previous setting.
NOTE:Pressing the ªLockº button on the key fob while
you are inside the vehicle will activate the Security
Alarm. Opening a door with the Security Alarm activated
will cause the alarm to sound. Press the ªUnlockº button
to deactivate the Security Alarm.Using the Panic Alarm
NOTE:The ªPanicº and ªSecurityº alarms are quite
different. Please take a moment to activate the ªPanicº
and the ªSecurityº modes to hear the differences in the
horn. In case one should go off in the future, you will
need to know which mode has been activated in order to
deactivate it.
To turn the panic alarm feature ON or OFF, press and
hold the ªPanicº button on the key fob for at least one
second and release. When the panic alarm is on, the
headlights and parking lights will flash, the horn will
pulse on and off, and the illuminated entry system will
turn on.
The panic alarm will stay on for 3 minutes unless you
turn it off by pressing the ªPanicº button a second time or
if the vehicle speed is 5 mph (8 km/h) or greater.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23
2

To remote start your vehicle, press and release the
ªRemote Startº button on the key fob twice within three
seconds. To indicate that the vehicle is about to start, the
parking lights will flash and the horn will sound briefly
(if programmed).Once the engine starts it will run for 15 minutes. To
cancel remote start, press and release the ªRemote Startº
button once.
To enter the vehicle while the engine is running during a
remote start, you must first unlock the vehicle using the
ªUnlockº button on the key fob. Once the vehicle is
unlocked, you have 60 seconds to enter the vehicle and
insert the key in the ignition and turn it to the ON
position. Otherwise, the system will cancel the remote
start and automatically turn off.
Remote start will also cancel if any of the following occur:
²If the engine stalls or RPM exceeds 2500.
²Any engine warning lamps come on.
²The hood is opened.
²The hazard switch is pressed.
²The transmission is moved out of P (Park).
Remote Start Button
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

inflation. These airborne particles may irritate the skin,
eyes, nose, or throat. If you have skin or eye irritation,
rinse the area with cool water. For nose or throat
irritation, move to fresh air. If the irritation continues,
see your doctor. If these particles settle on your
clothing, follow the garment manufacturer's instruc-
tions for cleaning.
²It is not advisable to drive your vehicle after the
airbags have deployed. If you are involved in another
collision, the airbags will not be in place to protect you.
WARNING!
Deployed airbags and seat belt pretensioners cannot
protect you in another collision. Have the airbags,
seat belt pretensioner, and seat belt retractor assem-
bly, replaced by an authorized dealer as soon as
possible. Also, have the Occupant Classification Sys-
tem serviced as well.
Enhanced Accident Response System
In the event of an impact that causes airbag deployment,
with the vehicle stopped, and the vehicle communication
network intact, and the power intact, the Enhanced
Accident Response System performs the following func-
tions:
²Cuts off fuel to the engine.
²Flashes hazard lights.
²Turns on the interior lamps which remain on as long as
the battery has power or until the ignition key is
removed.
²Unlocks the doors automatically
62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE