2008 DODGE NITRO engine

NOTE:Magnetic materials should be kept away from
the top of the right rear quarter window. This is where
the compass sensor is located.
To Set the Variance
Start the engine, and leave the transmission in the P
(Park) position. Press and hold (approximately ten sec-
onds) the odometer/trip odometer reset button until the
current variance zone number is displayed. To change the
zone, press and release the odometer/trip odometer reset
button to increment the variance one step. Repeat as
necessary, until the desired variance is achieved.
NOTE:The factory default zone is 8. During program-
ming, the zone value will wrap around from zone 15 to
zone 1.
Compass Calibration
If the compass appears erratic, inaccurate or abnormal,
you may wish to calibrate the compass. Prior to calibrat-
ing the compass make sure the proper zone is selected.
INSTRUMENT PANEL AND CONTROLS 183
4

To Manually Calibrate the Compass
Start the engine, and leave the transmission in the P
(Park) position. Press and hold (approximately 10 sec-
onds) the odometer/trip odometer reset button until the
current variance zone number is displayed. Release the
odometer/trip odometer reset button, then press and
hold again (approximately 10 seconds), until the direc-
tion is displayed with the ªCALº indicator on continu-
ously in the display. To complete the compass calibration,
drive the vehicle in one or more complete 360 degree
circles under 5 mph (8 km/h) in an area free from power
lines, large metallic objects, until the ªCALº indicator
turns off. The compass will now function normally.ELECTRONIC VEHICLE INFORMATION CENTER
(EVIC) Ð IF EQUIPPED
The Electronic Vehicle Information Center (EVIC) fea-
tures a driver-interactive display. It is located on the
instrument cluster in the lower half of the fuel/coolant
temperature gauge.
184 INSTRUMENT PANEL AND CONTROLS

²Right Front Low Pressure (with a single chime). Refer
to ªTire Pressure Monitoring Systemº in Section 5 of
this manual.
²Right Rear Low Pressure (with a single chime). Refer
to ªTire Pressure Monitoring Systemº in Section 5 of
this manual.
²Check TPM System (with a single chime). Refer to
ªTire Pressure Monitoring Systemº in Section 5 of this
manual.
²Check Gascap (refer to ªAdding Fuelº in Section 5 of
this manual for more details)
²Oil Change Required (with a single chime).
Oil Change Required
Your vehicle is equipped with an engine oil change
indicator system. The ªOil Change Requiredº message
will flash in the EVIC display for approximately 10
seconds after a single chime has sounded to indicate the
next scheduled oil change interval. The engine oil change
indicator system is duty cycle based, which means the
engine oil change interval may fluctuate dependent upon
your personal driving style. Unless reset, this message
will continue to display each time you turn the ignition
switch to the ON/RUN position. To turn off the message
temporarily, press and release the Menu button. To reset
the oil change indicator system (after performing the
scheduled maintenance) refer to the following procedure.
1. Turn the ignition switch to the ON position (Do not
start the engine).
2. Fully depress the accelerator pedal slowly three times
within 10 seconds.
INSTRUMENT PANEL AND CONTROLS 187
4

For UConnectŸ ªVoice Recognition System (VR) Ð If
Equipped º refer to ªHands-Free Communication (UCon-
nectŸ)º in section 3 of this manual for detailed operating
instructions.
Operating Instructions - Hands Free Phone
(UConnectŸ) (If Equipped)
Refer to ªHands-Free Communication (UConnectŸ)º in
Section 3 of this manual.
Operating Instructions - Satellite Radio Mode (If
Equipped)
Refer to ªSatellite Radioº in this section.
Operating Instructions - Video Entertainment
System (VESt) (If Equipped)
Refer to separate ªVideo Entertainment System (VESt)
Guide.ºDolby
Manufactured under license from Dolby Laboratories.
9Dolby9and the double-D symbol are trademarks of
Dolby Laboratories.
Macrovision
This product incorporates copyright protection technol-
ogy that is protected by U.S. patents and other intellec-
tual property rights. Use of this copyright protection
technology must be authorized by Macrovision, and is
intended for home and other limited viewing uses only
unless otherwise authorized by Macrovision. Reverse
engineering or disassembly is prohibited
DTS
9DTS9and9DTS 2.09are trademarks of Digital Theater
Systems, Inc.
212 INSTRUMENT PANEL AND CONTROLS

Circulation Control
Press the mode control knob
to activate the recirculation
mode. A lamp (in the knob)
will illuminate when you are
in recirculate mode. Press the
knob again to deactivate the
system. Only use the recircu-
lation mode to temporarily
block out any outside odors,
smoke, or dust and to cool the
interior rapidly upon initial start up in very hot or humid
weather.
NOTE:Continuous use of the recirculation mode may
make the inside air stuffy and window fogging may
occur. Extended use of this mode is not recommended.
In cold or damp weather, the use of the recirculation
mode will cause windows to fog on the inside because ofmoisture build up inside the vehicle. For maximum
defogging, select the Outside Air position.
NOTE:Recirculation mode will not operate in floor, mix
or defrost modes.
Air Conditioning Operation
Press the temperature control
knob to activate the air condi-
tioning mode. A lamp will
illuminate when the Air Con-
ditioning System is engaged.
Press the knob again to deac-
tivate the system.
NOTE:The air conditioning compressor will not engage
until the engine has been running for about 10 seconds.
238 INSTRUMENT PANEL AND CONTROLS

Operating Tips
Window Fogging
Windows will fog on the inside when the humidity inside
the vehicle is high. This often occurs in mild or cool
temperatures when it's rainy or humid. In most cases,
turning on the air conditioning (pressing the snowflake
button) will clear the fog. Adjust the temperature control,
air direction, and blower speed to maintain comfort.
As the temperature gets colder it may be necessary to
direct air onto the windshield. Adjust the temperature
control and blower speed to maintain comfort. Higher
blower speeds will reduce fogging. Interior fogging on
the windshield can be quickly removed by selecting the
defrost mode.
Regular cleaning of the inside of the windows with a
non-filming cleaning solution (vinegar and water works
very well) will help prevent contaminates (cigarettesmoke, perfumes, etc.) from sticking to the windows.
Contaminates increase the rate of window fogging.Summer Operation
Air conditioned vehicles must be protected with a high
quality antifreeze coolant during summer to provide
proper corrosion protection and to raise the boiling point
of the coolant for protection against overheating. A 50 %
concentration is recommended. Refer to Fluids and
Genuine Parts in Section 7 for the proper coolant type.
When using the air conditioner in extremely heavy traffic
in hot weather especially when towing a trailer, addi-
tional engine cooling may be required. If this situation is
encountered, operate the transmission in a lower gear to
increase engine RPM, coolant flow and fan speed. When
stopped in heavy traffic, it may be necessary to shift into
N (Neutral) and depress the accelerator slightly for fast
idle operation to increase coolant flow and fan speed.
INSTRUMENT PANEL AND CONTROLS 239
4

STARTING AND OPERATING
CONTENTS
mStarting Procedures.....................245
NManual Transmission..................245
NAutomatic Transmission................245
NNormal Starting......................245
NExtreme Cold Weather (Below ±20ÉF Or
±29ÉC).............................246
NIf Engine Fails To Start.................246
NAfter Starting........................248
mEngine Block Heater Ð If Equipped.........248mManual Transmission Ð If Equipped.........249
N6-Speed Manual Transmission............249
mAutomatic Transmission..................252
NShift Lock Manual Override Ð If Equipped . . . 253
NBrake/Transmission Interlock System.......254
N4±Speed Automatic Transmission (3.7L
Engine)............................255
N5±Speed Automatic Transmission (4.0L
Engine)............................260
NGear Ranges.........................260
5

NTire Spinning........................290
NTread Wear Indicators..................291
NLife Of Tire.........................292
NReplacement Tires.....................292
NAlignment And Balance.................293
mTire Chains...........................294
mTire Rotation Recommendations............295
mTire Pressure Monitor System (TPMS) Ð
If Equipped...........................296
NBase System Ð If Equipped..............299
NPremium System Ð If Equipped..........301
NGeneral Information...................305
mFuel Requirements......................306N3.7L Engine (If Equipped)...............306
N4.0L Engine (If Equipped)...............306
NReformulated Gasoline.................307
NGasoline/Oxygenate Blends..............307
NMMT In Gasoline.....................308
NMaterials Added To Fuel................308
NFuel System Cautions..................308
NCarbon Monoxide Warnings..............309
mAdding Fuel..........................310
NFuel Filler Cap (Gas Cap)...............310
NLoose Fuel Filler Cap Message............312
mVehicle Loading........................313
NCertification Label.....................313
STARTING AND OPERATING 243
5