2008 DODGE CALIBER SRT hood release

TO OPEN AND CLOSE THE HOOD
To open the hood, two latches must be released. First pull
the hood release lever located on the left kick panel.
Then move the safety catch located under the front edge
of the hood, near the center and raise the hood.Lift the hood prop rod, clipped to the left side (right side
facing hood) of the engine compartment, to secure the
hood in the open position. Place the hood prop at the
location stamped into the inner hood surface.
Primary Hood Latch
Secondary Hood Latch
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109
3

WARNING!
Fluid level should be checked on a level surface and
with the engine off to prevent injury from moving
parts and to insure accurate fluid level reading. Do
not overfill. Use only manufacturers recommended
power steering fluid.
If necessary, add fluid to restore to the proper indicated
level. With a clean cloth, wipe any spilled fluid from all
surfaces. Refer to ªFluids, Lubricants, and Genuine
Partsº for correct fluid types.
Front Suspension Ball Joints
There are two front suspension lower ball joints that are
permanently lubricated. Inspect these ball joints when-
ever under vehicle service is done. Damaged seals and
their corresponding potentially damaged ball joints must
be replaced.
Body Lubrication
Locks and all body pivot points, including such items as
seat tracks, doors, liftgate and hood hinges, should be
lubricated periodically to assure quiet, easy operation
and to protect against rust and wear. Prior to the appli-
cation of any lubricant, the parts concerned should be
wiped clean to remove dust and grit; after lubricating
excess oil and grease should be removed. Particular
attention should also be given to hood latching compo-
nents to insure proper function. When performing other
underhood services, the hood latch, release mechanism
and safety catch should be cleaned and lubricated.
The external lock cylinders should be lubricated twice a
year, preferably in the fall and spring. Apply a small
amount of a high quality lubricant such as MopartLock
Cylinder Lubricant directly into the lock cylinder.
306 MAINTAINING YOUR VEHICLE

NOTE:Inspection of brake hoses should be done when-
ever the brake system is serviced and at every engine oil
change.
WARNING!
Worn brake hoses can burst and cause brake failure.
You could have an accident. If you see any signs of
cracking, scuffing, or worn spots, have the brake
hoses replaced immediately.
Brake Master Cylinder
The fluid level in the master cylinder should be checked
when performing under hood services, or immediately if
the brake system warning lamp is on.
Be sure to clean the top of the master cylinder area before
removing the cap. If necessary, add fluid to bring the
fluid level up to the requirements described on the brakefluid reservoir. Fluid level can be expected to fall as the
brake pads wear. Brake fluid level should be checked
when pads are replaced. However, low fluid level may be
caused by a leak and a checkup may be needed.
NOTE:The Brake Fluid Reservoir supplies fluid to both
the Brake System and the Clutch Release System. The
two systems are separated in the reservoir and a leak in
one system will not affect the other system. TheManual
TransaxleClutch Release System should not require fluid
replacement during the life of the vehicle. If the Brake
Fluid Reservoir is low, and the brake system does not
indicate any leaks or other problems, it may be a result of
a leak in the Hydraulic Clutch Release System. See your
local authorized dealer for service.
Use only manufacturers recommended brake fluid, refer
to ªFluids, Lubricants, and Genuine Partsº for correct
fluid type.
316 MAINTAINING YOUR VEHICLE

Hands-Free Phone (UConnectŸ).............. 76
Hazard
Driving Through Flowing, Rising, or Shallow
Standing Water......................... 235
Hazard Warning Flasher................... 274
Head Restraints......................... 106
Headlights............................ 327
Cleaning............................ 321
High Beam........................ 114,165
High Beam/Low Beam Select Switch........ 114
Passing............................. 115
Replacing............................ 327
Switch.............................. 111
HomeLinkt(Garage Door Opener) Transmitter . . . 122
Hood Release.......................... 109
Hoses................................ 314
Ignition............................... 12
Key ................................. 12Ignition Key Removal..................... 12
Immobilizer (Sentry Key).................13,29
Infant Restraint.......................... 57
Information Center, Vehicle................. 166
Inside Rearview Mirror.................... 73
Instrument Cluster....................156,157
Instrument Panel and Controls.............. 155
Instrument Panel Cover................... 322
Instrument Panel Lens Cleaning............. 322
Integrated Power Module (Fuses)............ 323
Interior Appearance Care.................. 321
Intermittent Wipers (Delay Wipers)........... 117
Introduction............................. 4
Jump Starting.......................... 284
Key, Programming........................ 15
Key, Replacement........................ 14
Key, Sentry (Immobilizer)................... 13
362 INDEX