2008 Citroen NEMO height

42
Gearbox and steering wheel
Reverse gear
Never engage reverse gear before the
vehicle is completely stationary.
The lever should be moved slowly to reduce
the noise on engaging reverse gear. If your vehicle is fitted with parking
assistance, the system comes into
operation when reverse gear is engaged and
an audible signal is heard.
Refer to the “Rear parking assistance”
section of chapter 3.
ADJUSTING THE STEERING WHEEL MANUAL GEARBOX
Good practice
When the vehicle is stationary, unlock the
steering wheel by pushing the lever down.
Adjust the depth and height of the steering
wheel, then lock by pulling the lever up fully.
To change gear easily, always press the
clutch pedal fully.
To prevent the mat from becoming caught
under the pedal:
- ensure that the mat is positioned
correctly,
- never fit one mat on top of another.
Avoid leaving your hand on the gear knob as
the force exerted, even if slight, may wear
the internal components of the gearbox over
time.

45
2
Dimensions
TECHNICAL DATA
DIMENSIONS
The light van “L1” is the standard model, the “L2 - Worksite Pack” version is a model sold according to country:




Light van (in mm)
L1 L2 (Worksite Pack)
L Overall length
3 864 3 881
H Overall height 1 721 1 742
Height with roof bars 1 782 1 803
A Wheelbase 2 513
B Front overhang 760 777
C Rear overhang 591
D Overall width 2 019
Width (with mirrors folded) 1 816
E Width of front tracks 1 469 1 464
F Width of rear tracks 1 465
G Height of load sill 527 544
I Length of interior fl oor 1 523
J Maximum interior load height 1 205
K Maximum interior width (10 cm from the fl oor) 1 473
M Maximum interior width (at the sides) --
N Interior width between wheel arches 1 046

Volume
(m
3

) 2.5

47
2
Dimensions
TECHNICAL DATA
Combi (in mm)
Standard Raised
L Overall length 3 959 3 970
H Overall height 1 721 1 742
Height with roof bars 1 782 1 803
A Wheelbase 2 513
B Front overhang 855 866
C Rear overhang 591
D Overall width 2 019
Width (with mirrors folded) 1 816
E Width of front tracks 1 464
F Width of rear tracks 1 465
G Height of load sill 527 544
I Length of interior fl oor
743
Length of interior fl oor
(rear benchseat fully folded) 1 130
J Maximum interior load height
(under rear shelf) 592
K Maximum interior width (10 cm from the fl oor) 1 473
M Maximum interior width (at the sides) -
N Interior width between wheel arches 1 046

63
4
ERGONOMICS and COMFORT
Seats
FRONT SEATS
Head restraints
Head restraint height adjustment: to raise or
lower the head restraint, slide it by pressing
the lug.
The adjustment is correct when the upper
edge of the head restraint is level with the
top of the head.
To remove the head restraint, release the
base of the rod to press the tab and raise
the head restraint to the highest position.
To refit the head restraint, press the tab of
the lug and engage the head restraint rods
in the openings keeping them in line with the
seat back.

Never drive with the head restraints
removed. They must be in place and
adjusted correctly.

64
Seats
Seat cushion height
To adjust the height of the driver ’s seat
cushion, pull the control upwards as many
times as necessary to raise.
To lower, push the control downwards as
many times as necessary.
Forwards-backwards adjustment
Lift the control bar and slide the seat
forwards or backwards to the required
position.
Lumbar support
Turn the control.
Seat back angle
Turn the control to adjust the angle of the
seat back.

74
Practical information
LOAD SPACE LAYOUT
Stowing rings
There are 6 stowing rings on the rear floor to
secure your loads.
As a safety precaution in case of sharp
braking, you are advised to place heavy
objects as far forwards towards the driver ’s
seat as possible and immobilise the load by
securing it firmly using the stowing rings on
the floor.
Storage tray
A storage tray is provided at the rear left of
the load space.
Torch
A magnetic torch is provided at the rear right
of the load space.
Remove the torch from its base.
To change the 4 storage batteries (NiMH
type), remove the protective cover from the
torch.
To put the torch back in place, engage
it in the notches on the base and pivot it
upwards.
Ladder type vertical partition
Behind the driver ’s seat, a ladder type
vertical partition protects the driver against
the risk of load movement.
Partitions
Panel, glazed and mid-height panel
with grille type partitions are offered to
complement your light van.
The transportation of passengers in the
load space is not permitted.

110
Changing a fuse

Identification
mark
Amperage
Functions
F12 7.5 A Right-hand dipped headlamp supply
F13 7.5 A Left-hand dipped headlamp supply - hea dlamp height adjuster
F31 5 A Engine control unit supply switch
F32 7.5 A Front light - front courtesy light - r ear courtesy light lamp
F36 10 A Audio equipment - mobile telephone pre- equipment - air conditioning control panel - EODB diag socket
F37 5 A Brake light - instrument panel
F38 20 A Locking of the doors
F43 15 A Wipers pump
F47 20 A Driver ’s electric window motor supply
F48 20 A Passenger ’s electric window motor suppl y
F49 5 A Parking assistance control unit - rear l ighting switch - electric exterior mirrors
F50 7.5 A Air bags control unit
F51 5 A Switch on brake pedal - switch on clutch pedal
F53 5 A Instrument panel - rear fog lamps DRIVER’S SIDE FASCIA PANEL FUSES