2008 Citroen C4 PICASSO Instrument panel
[x] Cancel search: Instrument panelPage 89 of 266
88
II
Stopping the function
- by an action on the control on position "REG" to position 0.
- by the engine stopping.
The cruise speed previously cho-sen is no longer memorised.
If there is a malfunction,a mes-sage will display accompanied by a sound signal and lighting of the SERVICE warning lamp.
Contact a CITROËN dealer.
Cruise control should only be used when the driving conditions allow you to drive at a constant speed.
D o n o t u s e i t i n h e a v y t r a f fi c , o r o n d a n g e r o u s o r s l i p p e r y r o a d s .
The driver must remain attentive and in full control of his vehicle.
You are recommended to keep your feet within range of the pe dals.
To avoid any risk of interfering with the pedals :
- c h e c k t h a t t h e fl o o r m a t i s c o r r e c t l y p o s i t i o n e d ,
- n e v e r u s e m o r e t h a n o n e fl o o r m a t .
Re-engaging cruise control
-by recall of the memorised speed :
After a disengagement, press on button 3. Your vehicle automati-cally returns to the memorised cruise speed which is displayed in zone A.
If the memorised cruise speed is higher than the current speed, the vehicle wll accelerate to reach the former.
- by selection of the current speed :
Press on button 2 or 4 once the desired speed has been reached.The information "OFF" will thendisappear from zone A.
Observation : If during the opera-tion of cruise control, the system is unable to keep within the memo-rised speed (for example on a steep d e s c e n t ) , t h e n t h e s p e e d fl a s h e s . Adapt your speed as necessary.
Disengaging of cruise control while retaining the memorised speed
- Either by pressing on the brake pedal or on the clutch pedal.
- Or by pressing button 3.
- Or if either the ESP or the ASR system is active.
Note : cruise control is not active if the gear lever is in neutral.
These actions cause the informa-tion "OFF" to appear in zone A of the instrument panel.
These manœuvres do not cancel the cruise speed which remains displayed in the instrument panel.
C R U I S E C O N T R O L
Page 90 of 266
1
3
4
2
A
II
89
This driving assistance device en-ables you to choose a maximum speed that you wish not to exceed. This has to be higher than 30 km/h (around 20 mph).
The speed limiter controls are lo-cated on the steering wheel.
Note : The information relating to the speed limiter is displayed in zone A of the instrument panel.
Selection of the function
Rotate the control 1 to the "LIM"position.
On selection of the function, the previous memorised speed and the information "OFF" are displayed :
A d j u s t m e n t o f t h e m a x i m u m speed
With the engine running, you can adjust the memorised maximum speed , by means of short or long presses on :
- button 4 to increase the memo-rised maximum speed,
- button 2 to decrease the memo-rised maximum speed.
Note : successive presses will modify the maximum speed in steps of 1 km/h and a sustained press in steps of 5 km/h (3 mph).
A c t i v a t i o n o f t h e m a x i m u m speed
When the desired maximum speed is displayed, press button 3 so that the limitation is activated.The information "OFF" thendis-appears from zone A.While the function is active, press-ing the accelerator pedal will not en-able the programmed speed to be exceeded, except if you press the pedal hard down to beyond the end-of-travel switch (see “Temporary override of the maximum speed”).
Note : The speed of your vehicle may vary slightly in relation to that memorised.
Bi-tone instrument panel
S P E E D L I M I T E R
Page 91 of 266
90
II
Stopping the function
- by an action on the control on position "LIM" to position 0.
- by the engine stopping.
The speed previously chosen is still memorised.
If there is a malfunction,a mes-sage will display accompanied by a sound signal and lighting of the SERVICE warning lamp.
Contact a CITROËN dealer.
Temporary override of the m a x i m u m s p e e d
The accelerator pedal is equipped with an end-of-travel switch. If you action this switch by pressing the pedal hard down, you can exceed the memorised maximum speed at any time.
During the time the speed is being exceeded, the displayed speed fl a s h e s .
You have only to release the ac-celerator pedal to return below the maximum speed and render the function active again.
Observation : If during the operation of the speed limiter, the system is unable to keep within the maximum speed (for example on a steep de-scent or under heavy acceleration) t h e n t h e s p e e d fl a s h e s . A d a p t y o u r speed as necessary.
The function will re-engage when your speed returns below the de-sired maximum speed.
Disengagement of the m a x i m u m s p e e d
Press on button 3.
This action causes the information "OFF" to appear on the instru-ment panel screen.
U s e o f fl o o r m a t s t h a t a r e n o t a p p r o v e d b y C I T R O Ë N m a y h i n d e r access to the accelerator pedal and thus interfere with the func-tioning of the speed limiter.
To avoid any risk of interfering with the pedals :
- c h e c k t h a t t h e fl o o r m a t i s c o r r e c t l y p o s i t i o n e d ,
- n e v e r u s e m o r e t h a n o n e fl o o r m a t .
This action does not cancel the memorised maximum speed which remains displayed in zone A ofthe instrument panel.
S P E E D L I M I T E R
Page 97 of 266
A
96
III
Electrical control
From the driver’s seat position, the controls siutated on the door enable the vehicle’s electric win-dows to be actioned.
Note : The windows can also be operated for a short time after the ignition has been switched off (in-cluding after the front doors have been opened).
Sequential control
A n a c t i o n t o t h e fi r s t n o t c h o n t h e control starts a window movement which stops when the control is released. A press for about one second on the control will close or open the window fully, a further press will stop the movement.
PAY ATTENTION TO WHERE CHILDREN ARE WHEN OPERATING THE ELECTRIC WINDOWS.
Always remove the key from the ignition when leaving the vehicle, even for a short time.
When the driver is actioning the controls for the passenger win dows, he must make sure that no-one is obstructing the windows from lo sing properly.
The driver should ensure that the passengers use the windows cor-rectly.
If any person should be at risk of becoming trapped by the operation of the windows, you must reverse the movement of the glass. For t hat, reverse the position of the control concerned.
This is for deactivating operation of the electric windows and opening of the rear doors from the rear seat positions. It is activated by a press on the control A located on the window control panel or by an action on the locks of the rear doors. The warning lamp in the instrument panel comes on temporarily. Each time you switch on the ignition, the warning lamp lights up for a short time.
It is still possible to open the doors from the outside and to operate the rear windows from the front seat positions.
Anti-pinch
An anti-pinch device will stop the glass from rising. If it meet s an obstacle, it goes back down.
After a battery disconnection or following a malfunction, you have to re-initialise theanti-pinch function for each window :
- Use the control to open the window fully, then attempt to close it. It will rise only a few centimetres.
- Pull again on the control until the window closes fully. Once the window is closed, sustain the press on the control for one second.
Warning : During this operation, the anti-pinch protection is inoperat ive.
Child safety
E L E C T R I C W I N D O W S
Page 153 of 266
B
150
III
T h e r e a r p n e u m a t i c s u s p e n s i o n e n h a n c e s d r i v i n g c o m f o r t b y m a i n t a i n i n g a c o n s t a n t b o d y h e i g h t w h a t -ever the vehicle load.
OPERATION
- I f t h e r e i s a n i n c r e a s e i n v e h i c l e l o a d , a s i n k i n g o f the rear of the vehicle is detected and the pneumatic s p r i n g s i n fl a t e i n o r d e r t o c o m p e n s a t e f o r t h e e x t r a w e i g h t . - I f t h e r e i s a n d e c r e a s e i n l o a d , a r i s i n g o f t h e r e a r o f t h e v e h i c l e i s d e t e c t e d a n d s o t h e p n e u m a t i c s p r i n g s d e fl a t e t o r e t u r n t h e v e h i c l e t o i t s n o m i n a l h e i g h t . - I f t h e v e h i c l e h a s b e e n u n u s e d f o r a l o n g p e r i o d , t h e p n e u m a t i c s p r i n g s m a y i n fl a t e i f n e c e s s a r y w h e n y o u unlock or open a door, so as to return the vehicle to i t s n o m i n a l h e i g h t .
Note: I f y o u d o n o t r e a c t i v a t e t h e s y s t e m m a n u a l l y , t h e a u t o m a t i c c o r r e c t i o n w i l l b e a c t i v a t e d a s s o o n a s t h e v e h i c l e s t a r t s t o m o v e . D u r i n g t h e c o r r e c t i o n , t h e S E R V I C E w a r n i n g l a m p l i g h t s u p a n d a m e s s a g e o n t h e s c r e e n r e m i n d s y o u n o t t o e x c e e d 1 0 k m / h ( 6 m p h ) .
Note : the automatic correction does not function if the d o o r s o r t h e t a i l g a t e a r e o p e n .
T h e a u t o m a t i c c o r r e c t i o n o p e r a t e s e v e n i f y o u r v e h i c l e i s i n e c o n o m y m o d e .
ACTIVATION / DEACTIVATION
The automatic correction can be deactivated :
- Press on the button B f o r a p p r o x i m a t e l y t w o s e c o n d s .
- R e l e a s e t h e b u t t o n w h e n y o u h e a r a b e e p . D e a c t i v a t i o n i s c o n fi r m e d b y t h e l i g h t i n g o f t h e L E D o n t h e b u t t o n B.
I t i s e s s e n t i a l t h a t y o u s h o u l d d e a c t i v a t e t h e s y s t e m i n t h e f o l l o w i n g i n s t a n c e s :
- w o r k i n g u n d e r t h e v e h i c l e ,
- c h a n g i n g a w h e e l ,
- t r a n s p o r t i n g t h e v e h i c l e o n a t r u c k o r o n a b o o t .
To reactivate the automatic correction :
- P r e s s a g a i n o n t h e b u t t o n B f o r a p p r o x i m a t e l y t w o s e c o n d s .
- R e l e a s e t h e b u t t o n w h e n y o u h e a r a b e e p . A c t i v a - t i o n i s c o n fi r m e d b y t h e e x t i n c t i o n o f t h e L E D o n t h e button B.
In the event of the system malfunctioning, alert messages, always in association with the SERVICE warning lamp, will display in the instrument panel. Contact a CITROËN dealer as soon as possiblewarning lamp, will display in the instrument pan, will d.
Grand C4 PicassoC4 Picasso
P N E U M A T I C S U S P E N S I O N
Page 196 of 266
A
1
VI
193
C H A N G I N G A W H E E L
REMOVING A WHEEL
1. Park the vehicle on level, sta-ble and non-slippery ground. Apply the parking brake.
Switch off the ignition, check that the parking brake is ap-plied (message and warning lamp in the instrument panel) a n d e n g a g e fi r s t g e a r o r r e -verse gear depending on the slope (P if an automatic gear-box, D or R if a 6-speed elec-tronic gearbox).
2. Use a chock to secure the ve-hicle more safely. Place the chock in front of the wheel that is opposite the wheel affected.
3. Detach the trim using the re-moving tool 4, pulling in the area of the valve.
For vehicles with alloy wheels, insert the trim removing tool 1into the recess in the central trim and lever it off.
For vehicles with alloy wheels that have visible bolts, remove the chromes covers using the tool 2.
Before any operation of this sort, it is advisable to deactivate your pneumatic suspension (see “Pneumatic sus-pension”). When changing a wheel, it is essential to immobil ise the vehicle on ground that is level, stable and non-slippery.
4. Slacken the wheel bolts. For vehicles with alloy wheels, undo the anti-theft bolts using tool 9.
5. Position the jack under the vehicle (see diagrams), at the jacking point A closest to the wheel to be changed.
6. Unwind the jack 5 until its bracket is in contact with the ground. Make sure that the jack is vertical under the jack-ing point used.
7. Continue to extend the jack so as to raise the vehicle.
8. Undo the wheel bolts and re-move the wheel.