2008 Citroen C4 PICASSO door lock

1
2
84
II
REAR VIEW MIRRORS
ADJUSTMENT
This operates with the ignition switched on.
From the driver’s seat position, se-lect the rear view mirror by moving control 1 to the left or right, then adjust the rear view mirror in the four directions by acting on con-trol 2.
Demisting-deicing of the rear view mirrors is coupled with that for the rear screen.
REAR VIEW MIRRORS
FOLDBACK
When the vehicle is parked, the rear view mirrors can be folded back ei-ther manually or electrically.
Electrically
From the central position, a press to the rear on control 1 folds the rear view mirrors back.
The opposite movement is ob-tained by pressing again on the rear of the control.
Electrically and automatically
The rear view mirrors also fold back automatically when you lock the doors.
The rear view mirrors redeploy when you unlock the vehicle, un-less the foldback was performed manually. In this case, you have to press on the rear of the control to deploy them.
Note : The automatic foldback of the rear view mirrors can be deactivated. Contact a CITROËN dealer.
AUTOMATIC TILTING OF
REAR VIEW MIRRORS IN
REVERSE GEAR
This functions enables you to au-tomatically see the ground (pave-ment) when parking using reverse gear.
Adjusting the indexed position of the driver’s and passenger’s rear view mirrors
With the engine running :
- Select the rear view mirror using control 1.
- Engage reverse gear, the glass of the rear view mirror positions itself automatically to give a bet-ter sight of the pavement.
- If necessary, adjust your rear view mirror to your preference by means of the electrical control 2. This position is then memorised.
Stopping the rear view mirror indexing function
To stop the function, move control 1 to the central position.
Note : The rear view mirrors re-turn to their original position :
- 20 seconds after reverse gear has been disengaged,
- once you reach a speed of over 10 km/h (approx. 6 mph).
E X T E R I O R R E A R V I E W M I R R O R S

A
96
III
Electrical control
From the driver’s seat position, the controls siutated on the door enable the vehicle’s electric win-dows to be actioned.
Note : The windows can also be operated for a short time after the ignition has been switched off (in-cluding after the front doors have been opened).
Sequential control
An action to the fi rst notch on the control starts a window movement which stops when the control is released. A press for about one second on the control will close or open the window fully, a further press will stop the movement.
PAY ATTENTION TO WHERE CHILDREN ARE WHEN OPERATING THE ELECTRIC WINDOWS.
Always remove the key from the ignition when leaving the vehicle, even for a short time.
When the driver is actioning the controls for the passenger win dows, he must make sure that no-one is obstructing the windows from lo sing properly.
The driver should ensure that the passengers use the windows cor-rectly.
If any person should be at risk of becoming trapped by the operation of the windows, you must reverse the movement of the glass. For t hat, reverse the position of the control concerned.
This is for deactivating operation of the electric windows and opening of the rear doors from the rear seat positions. It is activated by a press on the control A located on the window control panel or by an action on the locks of the rear doors. The warning lamp in the instrument panel comes on temporarily. Each time you switch on the ignition, the warning lamp lights up for a short time.
It is still possible to open the doors from the outside and to operate the rear windows from the front seat positions.
Anti-pinch
An anti-pinch device will stop the glass from rising. If it meet s an obstacle, it goes back down.
After a battery disconnection or following a malfunction, you have to re-initialise theanti-pinch function for each window :
- Use the control to open the window fully, then attempt to close it. It will rise only a few centimetres.
- Pull again on the control until the window closes fully. Once the window is closed, sustain the press on the control for one second.
Warning : During this operation, the anti-pinch protection is inoperat ive.
Child safety
E L E C T R I C W I N D O W S

A
III
97
If you decide to drive with the doors locked, be aware that this will make access more diffi cult for the emergency services in the event of an accident.
Note : the control A is inactive when the vehicle has been locked by means of the remote control or the key
Door selectivity
If you have selected “plip action : driver’s door" in the multifunction screen menu :
- a press on the remote control opens the driver’s door,
- a second press opens all the doors.
Anti-intrusion security
On starting the vehicle, the system automatically locks the doors w hen you have reached a speed of around 10 km/h (6 mph).
Note : Whenever a door is opened, the door will lock again automatically when the vehicle reaches a speed of around 10 km/h (6 mp h).
Activation / Deactivation of the function
After switching on the ignition, give a long press on the ce ntral unlocking control until you see a message displayed and a sound signal is emitted.
Locking from the inside
A press on the control A operates the electric central locking and un-locking, provided the doors and tailgate are closed.
The doors can still be opened from the inside.
If one of the doors is open or not properly closed, the central lock-ing does not operate.
The warning lamp on the control A signals 3 statuses :
- It fl ashes when the doors are locked, with the vehicle stationary and the engine turned off.
- It lights up when the doors are locked, or when the ignition is switched on.
- It goes out if the doors are not locked.
A C C E S S T O T H E V E H I C L E

CB
98
III
A C C E S S T O T H E V E H I C L E
Emergency unlocking of the boot
Should there be a problem with the boot lock, or a battery failure :
- From the interior of the bootspace, face the rear of the vehicle.
- Insert the point of a screwdriver into the aperture Cof the lock.
- Push the white component inside the lock to the left, to unlock the boot.
Manual control (emergency mode)
Should there be an electrical failure it is possible to lock the vehicle’ doors by actioning the control B on each door.
With the door open, insert for example the end of the ignition key into the aperture and turn it.
Close the door.
After a repair, normal functioning resumes by means of the unlocking control A, the remote control or the key used in the driver’s door.

III
105
A U T O M A T I C A I R C O N D I T I O N I N G
(Function for retaining ventilation with the engine switched off : REST function, continued…)
Engine stopped, ignition switched on :- The displays will light up, with the air blower shown empty as long as the function is available.- A press on the REST button activates the function for a timing of just a few minutes. Two blades of the blower will fi ll to signify that the function is active.- It can be deactivated and reactivated during the timing.- At the end of the timing, the display will go off.
On stopping the engine :- The displays remain lit up, the blower is shown em pty and the function can be activated for 30 seconds.- A press on the REST button during the next 30 sec-onds activates the function for a timing of several min-utes. The duration and availability of the function are variable according to the state of charge of the battery (a protection to guarantee engine starting). Two blower blades fi ll up to signify that the function is active. It re-mains active, even after the doors have been locked , until the end of the timing.- A further press before the end of the timing defi nitively stops the function.
Note : This button does not activate the air conditioning, only the air blowers. In the REST function, the air fl ow and distribution are controlled automatically and you c annot modify them.
4 - Adjustment of the air distribution- Press on button 4 so that the air fl ows scroll succes-sively on the display.
5 - Air recirculation
This button activates the recirculation of air within the passenger compartment and also has an automatic function.
The air distribution you have chosen is con-fi rmed by the lighting of the corresponding warning lamps in the display.
There are 7 possible adjustments.
Entry of air in automatic mode (activated by default, in automatic comfort regulation)
Automatic mode makes use of an air quality sensor. This analyses the air and isolates the passenger com-partment from the exterior as soon as it detects the presence of pollutants. Then it automatically activates recirculation of cabin air.
1
Closing of the air inlet
- Press on button 5 to close off the entry of air from outside.2
Whilst retaining the other adjustments, this position enables the driver at any time to exclude any disa-greeable odours or fumes coming from outside the vehicle.
It should be cancelled as soon as possible to permit renewal of cabin air and to prevent misting.
- Press once on button 5 to return to the initial status (entry of air in automatic mode).
Note : The airrecirculation can also be accessed by means of a press on the control located low down to one side of the steering wheel (see “Fixed centred controls steering wheel").
Entry of air (manual mode)
- Press on button 5 to activate entry of air from the outside. The warning lamp goes out. 3

E
III
117
“CINEMA SEAT" POSITION
This position allows you to free up space between the fi rst row and the second row.
Pull the control E under the seat.
Note : This position is only pos-sible with the lateral seats.
ACCESS TO THE THIRD ROW SEATS
The third-row seats can be accessed via the lateral second-row seats.
1. Pull the control E. The seat un-locks and the seat base comes up against the backrest.
2. Hold the control E in the raised position, pushing forwards. The whole slides towards the front seat.
3. Raise and lock the rigid plate.
Space becomes free behind the seat, the third-row passengers can get to their seats.
To exit the third-row seat positions :
1. Hold the control E in the raised position. The seat unlocks and the seat base comes up against the backrest.
2. Push the seat backrest, still holding the control E in the raised position.
Note : if the table on the back of the fi rst-row seat is down, close it to enable this operation.
Repositioning the seat,
from the exterior,
with the door open
If there are passengers seated in the third row :
1. Manually return the assembly as far as possible rearwards. The seat does not return as far as the maximum rearwards position, so as to retain leg space for the third-row pas-sengers.
2. Fold the seat base.
S E C O N D R O W S E A T S G R A N D C 4 P I C A S S O

III
127
Manual control
The rear doors are locked by op-erating the lever.
When the manual safety is in use, the aperture is at an angle.
Electric operation
The electrical safety is activated by pressing the control located to the rear of the electric windows panel. This prohibits movement of the rear electric windows and opening of the rear passenger doors.
It is still possible to open the doors from the outside, provided the ve-hicle is not locked.Note : with the ignition on, if the child safety is activat-ed for the two rear doors, the warning lamp comes on then goes out again approx. 10 seconds after the engine is started.
When the ignition is switched on, the warning lamp comes on then goes out again approx. 10 seconds after the engine is started.
Note : Activation of the function is confi rmed by the temporary light-ing of the warning lamp accompa-nied by a message.
C H I L D S A F E T Y
This system works independ-ently and in no way replaces the central locking controls.
Check the status of the child safety function each time you start the vehicle.
Always remove the key from the ignition when leaving the vehicle, even for a short time.
In the event of a serious impact, the electrical child safety func-tion is automatically deactivat-ed to allow the rear passengers to exit the vehicle.

B
150
III
The rear pneumatic suspension enhances driving comfort by maintaining a constant body height what-ever the vehicle load.
OPERATION
- If there is an increase in vehicle load, a sinking of the rear of the vehicle is detected and the pneumatic springs infl ate in order to compensate for the extra weight.- If there is an decrease in load, a rising of the rear of the vehicle is detected and so the pneumatic springs defl ate to return the vehicle to its nominal height.- If the vehicle has been unused for a long period, the pneumatic springs may infl ate if necessary when you unlock or open a door, so as to return the vehicle to its nominal height.
Note: If you do not reactivate the system manually, the automatic correction will be activated as soon as the vehicle starts to move. During the correction, the SERVICE warning lamp lights up and a message on the screen reminds you not to exceed 10 km/h (6 mph).
Note : the automatic correction does not function if the doors or the tailgate are open.
The automatic correction operates even if your vehicle is in economy mode.
ACTIVATION / DEACTIVATION
The automatic correction can be deactivated :
- Press on the button B for approximately two seconds.
- Release the button when you hear a beep. Deactivation is confi rmed by the lighting of the LED on the button B.
It is essential that you should deactivate the system in the following instances :
- working under the vehicle,
- changing a wheel,
- transporting the vehicle on a truck or on a boot.
To reactivate the automatic correction :
- Press again on the button B for approximately two seconds.
- Release the button when you hear a beep. Activa-tion is confi rmed by the extinction of the LED on the button B.
In the event of the system malfunctioning, alert messages, always in association with the SERVICE warning lamp, will display in the instrument panel. Contact a CITROËN dealer as soon as possiblewarning lamp, will display in the instrument pan, will d.
Grand C4 PicassoC4 Picasso
P N E U M A T I C S U S P E N S I O N