2008 Citroen C4 PICASSO air condition

6
7
8
9
101
234
III
103
A U T O M A T I C A I R C O N D I T I O N I N G
1 - Automatic comfort regulation
A press on this button, confi rmed by the dis-play of the A/C warning lamp and of AUTO on the screen, provides automatic control, at the temperature selected, of all the following 5 functions :
- air fl ow,
- cabin temperature, on left hand side and right hand side,
- air distribution,
- air conditioning,
- automatic air recirculation.
For this facility to operate, it is recommended to keep all the air vents open.
Using the AUTO mode will prevent misting inside the vehicle in cold or humid weather.
Note : When starting from cold, in order to avoid a rush of cold air, the blower attains its optimum level progressively.
Manual resumption of one or more functions
It is possible to adjust each of the functions 4, 6 and 10 manually. The display of the "AUTO" function will then go off.
Resumption by the driver of the adjustment of cabin temperatures (for the front and rear passengers)
-A long press on this button will realign the tem-peratures for all passengers with the preferences of the driver.
A. DRIVER’S CONTROL PANEL

III
105
A U T O M A T I C A I R C O N D I T I O N I N G
(Function for retaining ventilation with the engine switched off : REST function, continued…)
Engine stopped, ignition switched on :- The displays will light up, with the air blower shown empty as long as the function is available.- A press on the REST button activates the function for a timing of just a few minutes. Two blades of the blower will fi ll to signify that the function is active.- It can be deactivated and reactivated during the timing.- At the end of the timing, the display will go off.
On stopping the engine :- The displays remain lit up, the blower is shown em pty and the function can be activated for 30 seconds.- A press on the REST button during the next 30 sec-onds activates the function for a timing of several min-utes. The duration and availability of the function are variable according to the state of charge of the battery (a protection to guarantee engine starting). Two blower blades fi ll up to signify that the function is active. It re-mains active, even after the doors have been locked , until the end of the timing.- A further press before the end of the timing defi nitively stops the function.
Note : This button does not activate the air conditioning, only the air blowers. In the REST function, the air fl ow and distribution are controlled automatically and you c annot modify them.
4 - Adjustment of the air distribution- Press on button 4 so that the air fl ows scroll succes-sively on the display.
5 - Air recirculation
This button activates the recirculation of air within the passenger compartment and also has an automatic function.
The air distribution you have chosen is con-fi rmed by the lighting of the corresponding warning lamps in the display.
There are 7 possible adjustments.
Entry of air in automatic mode (activated by default, in automatic comfort regulation)
Automatic mode makes use of an air quality sensor. This analyses the air and isolates the passenger com-partment from the exterior as soon as it detects the presence of pollutants. Then it automatically activates recirculation of cabin air.
1
Closing of the air inlet
- Press on button 5 to close off the entry of air from outside.2
Whilst retaining the other adjustments, this position enables the driver at any time to exclude any disa-greeable odours or fumes coming from outside the vehicle.
It should be cancelled as soon as possible to permit renewal of cabin air and to prevent misting.
- Press once on button 5 to return to the initial status (entry of air in automatic mode).
Note : The airrecirculation can also be accessed by means of a press on the control located low down to one side of the steering wheel (see “Fixed centred controls steering wheel").
Entry of air (manual mode)
- Press on button 5 to activate entry of air from the outside. The warning lamp goes out. 3

106
III
A U T O M A T I C A I R C O N D I T I O N I N G
6 - Adjustment mode for the rear passengers8 - Deicing / demisting of the rear screen
This can only operate when the engine is running.
- Press on button 8 to activate/deactivate the electric deicing of the rear screen and, according to version, of the exterior rear view mirrors. The warning lamp lights up and the symbol appears on the display.
It switches off automatically to prevent excessive con-sumption of power
9 - Rapid deicing / demisting of the front and rear windows
- Press on button 9. The warning lamp lights up.
This button decides whether or not the rear passengers may use their adjustment controls.
There are three possible statuses for this button :
Locking of the rear passenger controlsThe driver imposes his adjustment on the rear passengers.
Authorisation of the rear passenger controls
The rear passengers can use their adjustment controls at their conven-ience.
Closing of the air fl ow for the rear passengers
The supply of air is cut off.
7 - Panel display mode : black panel function
This function turns the displays and panel backlighting on or off.
- Function activated, a press on any button will light up the screen temporarily.
- A press on button 7 deactivates the function, lighting of buttons and screen is again permanent.
Note : This function optimises notably the visual com-fort for driving at night.
This function gives a rapid deicing / demisting of the vehicle simultaneously with :
- front deicing at optimum temperature,
- optimum air fl ow,
- recirculation prohibition,
- deicing of the rear view mirrors and heated rear screen,
- air conditioning, if necessary.
Press again on button 9 or on " AUTO " to stop the function. Deicing of the rear view mirrors and heated rear screen remains activated.
10 - Air conditioning
- Press on button 10 to activate the air conditioning.
The A/C warning lamp lights up.
With additional air conditioning, in cold weather you are advised to close the supply of air to the rear pas-sengers (no hot air distribution possible via these air vents).

1
2
108
III
AUTOMATIC AIR CONDITIONINGA D D I T I O N A L A I R C O N D I T I O N I N GC. REAR PASSENGER CONTROL PANELS
(RIGHT / LEFT)
1. Adjustment of temperature
The rear passengers can adjust their temperature controls independently via buttons + and -.
Note : Their preference cannot be greater than that of the driver by more than 2. The reaching of this maximum preference is confi rmed by th e fl ash-ing of its display.
2. Adjustment of air blower speed
The air blower operates only when the engine is running.
To adjust the fl ow of air, press on button :
to increase the air fl ow
to decrease the air fl ow
The level of air fl ow is indicated on the display by the progressive fi lling of the ventilator blades.
By decreasing the fl ow to zero, you deactivate the air conditio ning system (OFF).
Note : you can adjust the temperature and the air fl ow only if the driver enables you to (see button 6 of the driver’s control panel).
This warning lamp signifi es that the passenger controls are locked, you can adjust neither the temperature nor the air fl ow, which remain aligned on the preferences of the driver.
This warning lamp indicates that the supply of air is cut off.
Additional air conditioning allows you to optimise comfort levels in warm weather conditions. It pro-duces additional fresh air which is supplied using the rear air vents. The supply of warm air via the rear air vents is not possible using this system.
This position is recommended in cold weather conditions, as th e air vents do not supply warm air.

III
109
- Heating /Manual air conditioning
To make the best use of the system, we recommend :
- Automatic air conditioning
With automatic air conditioning, you are recommended to choose AUTO operation.
V E N T I L A T I O N - H E A T I N G -
A I R C O N D I T I O N I N G

194
VI
C H A N G I N G A W H E E L
WHEEL FOR TEMPORARY USE
If your vehicle is equipped with a spare wheel for temporary use only, when fi tting this it is normal to observe that the wheel bolts do not come to bear directly on the wheel rim.
The spare wheel is secured by the conical tapering of the wheel bolt’s shaft (see illustration).
When refi tting the original wheel, ensure that the wheel bolt contact surfaces are clean and in good condition.
WHEEL EQUIPPED WITH DEFLATION DETECTION SYSTEM
Such wheels have tyre pressure sensors. It is essential to have re-pairs carried out by a CITROËN dealer.
ANTI-THEFT BOLTS (alloy wheels)
Each wheel may be equipped with one anti-theft bolt.
To remove it :
1. Remove the protector that is covering it by means of the tool 2 (for removing the chrome covers on alloy wheels).
2. Use the anti-theft socket 9with the handle.
DIMENSION OF THE SPARE WHEEL
If your spare wheel has dimen-sions different from those of the normal vehicle wheels (identifi ed by a label), it is imperative to use the spare wheel only temporarily, to drive with caution, not to exceed 80 km/h (50 mph) and to have the tyre repaired and the normal wheel refi tted as soon as possible.
Tyre pressures
These are indicated on the label on the front left-hand door pillar (see "Vehicle Identifi cation").
The wheel bolts are specifi c to each type of wheel.
If new wheels are fi tted, check with your CITROËN dealer that the wheel bolts are compatible with the new wheels.
Note : take care to note down the code number on the head of the anti-theft bolt socket. This will enable you to obtain a replacement anti-theft socket from a CITROËN dealership.theft bolt socket. This will enable you This will
REFITTING A WHEEL
1. Position the wheel with the aid of the centring guide 3.
2. Do up the 3 bolts by hand, then remove the centring guide 3. Position the 4th bolt.
3. Pre-tighten the wheel bolts, using the wheelbrace 4.
4. Retract the jack 5 and disen-gage it.
5. Tighten the wheel bolts, using the wheelbrace 4.
6. Ensure that the tyre pressure is correct (see “Vehicle identi-fi cation”).

4848
V
T E L E P H O N E
T E L E M A T I C S E R V I C E S
To benef it from the localised emergency service with vehicle location, you have:to have signed the general conditions of the service stated on your vehicle order form, or have signed the specifi c CITROËN the service stated on your vehicle order order
Emergency Contract,to have made an initial call to the CITROËN Emergency service.To initialise this service:press on the SOS button, with the vehicle stationary and parked in the open air in an area covered by your mobile telephone operator,be prepared to refer to your registration document,specify to the operator that you are mak-ing a “ CIT RO ËN Em er gency ser v ic e specify to the operator that you are mak-e ope
initialisation” call.
When should you use this service ?In an emergency situation (accident with injuries, assault, etc.).
How to access this service ?Press on the SOS button of your NaviDrive.You are put in contact with our specialised assistance platform. An operator will rapidly assess the situation and if necessary send help to the spot.Your vehicle is automatically located thanks to the GPS function of your NaviDrive.