2008 Citroen C4 PICASSO DAG display
[x] Cancel search: displayPage 160 of 266
157
Manual pre-setting
Select the waveband and memory bank required using button E.
Select a station using either auto-matic or manual search.
Keep pressing for more than two seconds on one of the pre-selection buttons 1 to 6 on the keypad P.
The sound momentarily cuts off, then returns to its previous level to c o n fi r m t h a t i t h a s m e m o r i s e d t h e station.
Automatic memorisation of transmitters (Autostore function)
In FM, if you hold down button Efor more than two seconds, your radio will automatically memorise the 6 strongest stations on the FM3 memory bank.
The display shows “FM AST”.
The radio memorises the 6 strong-est transmitters, deleting the 6 previously memorised.
After the memorisation, the ra-dio goes directly to memory 1 of memory bank FM3.
Note :
- I f t h e t r a f fi c i n f o r m a t i o n f u n c t i o n has been activated (see RDS SYSTEM), the stations offering this facility will be memorised as priority.
- If it is unable to memorise any new stations, the system will re-tain the previously memorised stations.
- I f t h e s y s t e m i s u n a b l e t o fi n d 6 s t a t i o n s , t h e u n fi l l e d m e m o r y slots will remain free.
Recall of pre-set stations
Press button E b r i e fl y t o s e l e c t t h e required waveband and memory bank.
A short press on one the pre-selection buttons 1 to 6 on the keypad P recalls the correspond-ing memorised station. You can also do this using the control 3 at the steering wheel.
If it is a RDS station, the frequency appears some seconds before the name appears.
For RDS stations, recall of a sta-tion may prompt a search for a frequency corresponding to the region where you happen to be (see RDS system).
R A D I O S O U R C E
Page 161 of 266
IV
Using the RDS (radio data system) function on FM
The majority of FM radio stations use the RDS system. The radio in your vehicle has this system,.
The RDS system enables these stations to transmit non-audible data in addition to the broadcasting of their programmes. The data provides access to various functions described in this chapter, such as: display of the station name, inter- m i t t e n t t r a f fi c i n f o r m a t i o n fl a s h e s o r automatic scanning of stations. This enables you to continue listening to your chosen radio station, regard-less of the different frequencies it uses in the regions through which you are travelling.
Scanning of RDS stations
Your radio keeps the best pos-sible reception by continuously looking for any other frequencies on which the selected radio sta-tion is broadcast, automatically choosing the frequency offering the best reception (providing the station broadcasts on more than one transmitter or frequency).
Activation/deactivation of the RDS functions
The RDS functions can be accessed via the following two menus :
- Main menu (press button O).
- Audio menu (press button L).
To activate/deactivate the RDS functions on multifunction screen C :
1. Press button O.
2. Select the AUDIO icon using buttons J or M.
3. C o n fi r m y o u r c h o i c e w i t h a press on button L.
4. Select the sub-menu for the FM waveband, via buttons Jor M . C o n fi r m y o u r c h o i c e w i t h a press on button L.
5. Select scanning for RDS stations, via buttons J or M.
6. Validate your choice with a press on button L.
7. Using control L, select/deselect to activate/deactivate the function.
8. Validate your choice by selecting “OK” on the display.
To activate/deactivate the RDS functions on multifunction screen A :
1. Press button O.
2. Select the AUDIO-CD icon via buttons J or M.
3. Select scanning for RDS stations, via buttons J or M. The system tells you the status (active or inactive) of the function.
4. Modify this status via buttons K or N.
5. Then please wait for the display to disappear.
Note :
If the RDS function is active :
The “RDS” on the display will light up provided the station being re-ceived uses the RDS system with scanning of frequencies.
The “RDS” on the display is barred if the station received uses the RDS system without frequency search.
If your RDS function is deactiva-ted, the “RDS” on the display will be absent in all cases.
The display will indicate the “NAME” for the stations that use the RDS system and the frequency for stations that do not use it.
R D S S Y S T E M
Page 162 of 266
159
Regional search mode
Some stations, when they are or-ganised in networks, broadcast regional programmes at certain times of day, and national pro-grammes at other times.
It is possible to search :
- Either for a regional station only.
- Or across the whole network in o r d e r t o fi n d a d i f f e r e n t p r o g r a m m e.
To activate/deactivate this func-tion, proceed as for Scanning of RDS stations.
Note :
When this mode is activated, the system will remain tuned to one s p e c i fi c r e g i o n a l s t a t i o n .
T A t r a f fi c i n f o r m a t i o n ( t r a f fi c a n n o u n c e m e n t s )
Some stations allow broadcasting, only in FM, of these messages thanks to the “TA” function.
You can activate the “TA” func-tion by pressing on button I. This allows you, even though you are listening to another audio source or to a radio programme not itself p r o v i d i n g t r a f fi c m e s s a g e s , t o r e - c e i v e t r a f fi c i n f o r m a t i o n fl a s h e s from an FM station which broad-casts them.
While the messages are being broadcast the original source is paused and when the messages have ended your radio will auto-matically revert to the music pro-gramme you were listening to.
Notes :
- You have to be in FM wave band.
- The station being listened to should indicate via the RDS system that it b r o a d c a s t s t r a f fi c i n f o r m a t i o n.
- Stations organised in a network (EON) have regional transmitters that send their own programmes: while you are listening to one of these stations the system will switch automatically to a station on the network that is broadcast- i n g t r a f fi c i n f o r m a t i o n .
- You can stop listening to a mes-sage by pressing button I.
Sound volume adjustment for t r a f fi c i n f o r m a t i o n
T h e s o u n d v o l u m e f o r t r a f fi c i n f o r -mation operates separately from that for the rest of the system, and can be adjusted independently.
Rotate button A w h i l e a t r a f fi c information message is being broadcast.
This volume adjustment is memo-rised.
Selecting a programme type
Certain stations offer the possibi-lity of listening to a particular pro-gramme type, selected from a list (PTY).
Press for more than two seconds on button I.
Press on buttons J or M to scroll through and select the programme type you prefer, then press on but-ton L to validate your choice.
Searching for a station broadcasting this programme type
When you have chosen a pro-gramme type, the list of corres-ponding stations appears on the display, press on buttons J or M to scroll down and select the station you want, then press on button Lto validate your choice.
Quitting pty mode
To quit “PTY” mode, select the function to deactivate “PTY” in the list of the different programme types.
Radio text via contextual menu
This function allows to view the information broadcast by the sta-tion, concerning the programme you are currently listening to.
To activate/deactivate this func-tion, proceed as for Scanning of RDS stations.
R D S S Y S T E M
Page 164 of 266
161
C D S O U R C E
MP3 CD player
Your Audio CD system may be MP3 compatible.
As you insert a CD recorded in MP3 format, playback starts of the fi r s t s o n g o f t h e fi r s t C D - c o v e r .
You can select a particular track by using buttons N or K and CD-covers using buttons J or M.
To select a track
To display the list of CD-covers, press on button G.
Use buttons J or M to select the CD-cover you wish to listen to.
To open a CD-cover, press L.
Use buttons N or K to select the track you wish to listen to.
Validate by pressing button L or control 7 at the steering wheel.
Menu
This menu is for activation/deacti-vation of three options :
- P l a y b a c k o f t h e fi r s t 7 s e c o n d s (approx.) of each track of the CD.
- Repetition of the current CD-cover.
- Random playback of CD-cover tracks by CD-cover.
This can be accessed in two ways :
- Either by pressing button O and proceeding as for Search of Sta-tions RDS – for screen C, the sub-menu corresponds to the Audio Preferences.
- Or, provided you are in CD source, by pressing onbutton L. You can then access the Audio menu (for screen C only).
Page 166 of 266
163
- The telephone detects the Blue-tooth system on your vehicle. “CITROËNtooth systemh syst” displays on your telephone.
You should then select “CITROËN” on your telephone controls. Next you must choose whether or not to accept this twinning then select, on screen C using J, M or 8, one of the 4 memories. Validate with a press on button L or 7.
Note :
You can select a memory already attributed, although the telephone twinned to this location will no longer be attributed.
- Next the telephone asks you to en- t e r a n i d e n t i fi c a t i o n c o d e : 1234.
- Validate.
Notes:
This entry may be demanded ear-lier in the twinning sequence.
The telephone is now twinned to your Bluetooth system. For imme-diate access to the Bluetooth func-tions, it may be necessary to make a connection (see following page, C o n fi g u r a t i o n : C o n n e c t i n g a twinned mobile telephone). O n c e t h e t w i n n i n g i s fi n i s h e d , y o u will be able to connect your tele-phone via the “Main menu”.
Connecting a twinned telephone
Each time you enter the vehicle, after switching on the audio sys-tem, your telephone is detected
automatically. If more than one telephone is present, the last telephone to have been connect- e d i s t h e fi r s t t o b e r e c o g n i s e d .
Note :
Disconnections may occur. You may have to make a new connec-tion (see following page, C o n fi g u -ration : Connecting a twinned mobile telephone).
Observations :
- In the event of a problem, it is recommended to switch your telephone off and then on again.
- If you switch off your telephone w i t h i n t h e fi e l d o f r e c e p t i o n o f t h e Bluetooth system on your vehi-cle, the next connection will not be automatic. To restore auto-matic connection, you will have to connect your telephone manually (see following page, C o n fi g u r a -tion : Connecting a twinned mobile telephone).
- If you are already in telephone communication when the audio system is turned on, the latter detects the telephone.
- To avoid interference, you are advised not to place your mobile telephone close to your radio.
To accept an incoming call
Use button L or control 7 at the steering wheel.
Your audio system may be Bluetooth compatible. It allows you to connect a mobile telephone for “hands free” use and even to use its directory.It permits you to twin up to four telephones, to be able then to con-nect whichever one you choose.The Bluetooth functions available and the content of the display are dependent on the type of mobile telephone, its settings and the type of contract you have. For this rea-son it is advisable to make enqui-ries with your telephone provider.Prior to any operation :Your display should be lit up (key in position M).Your telephone’s Bluetooth sys-tem must be activated.
Twinning a telephone
Twinning a telephone consists of having it recognised by the Bluetooth system on your vehicle. This then permits an instantaneous connec-tion.
Twinning can only be performed with ignition switched on, dis-play illuminated, engine stopped. No other telephone should be connected.
The twinning must be performed with the telephone and its Blue-tooth system activated.
Notes : Refer to the user instructions to fa-miliarise yourself with the features of twinning.
B L U E T O O T H®
Page 167 of 266
IV
Main Menu
Press on the Menu control O to access the Main Menu, then se-lect the “Telephone” icon via but-tons J, M or 8 and then validate the selection via button L or 7.
You have access :
- To the Directory.
- T o C o n fi g u r a t i o n .
- To Communication Management.
You access your choices using J, M or 8 then you validate them with a press on L or 7.
This main menu can also be ac-cessed by pressing button E then button L.
Directory
This menu lets you open :
The telephone Directory of the telephone that is connected.
The Calls List.
This menu can also be accessed with a press on control 11.
Telephone directory
The starting of a telephone call can be done independently of the telephone or of the audio system, thanks to the directory.
The directory is displayed. Select the number via J, M or 8, then vali-date with a press on L or 7.
Observations :
The directory displayed updates itself automatically.
If the person to be called does not fi g u r e i n t h e d i r e c t o r y , t h e c a l l c a n only be made starting from the telephone.
If you have information recorded in the Vcard format, you must se-lect the person you wish to call, then validate. A list of 4 numbers maximum can be displayed with the following labels : “Home”, “Of- fi c e”, “Mobile” and “Car”.
Calls list
After selecting this component and then validating, the calls list is displayed with a maximum of : 10 calls made (arrow pointing up-ward), 10 calls received (arrow pointing downward) and 10 calls not connected.
It is possible to make a call starting from this list : Select the number via J, M or 8, then validate with a press on L or 7.
C o n fi g u r a t i o n
This menu allows you to :
- Delete a twinning.
Using J, M or 8, select this choice then validate via L or 7. Select in the list the telephone that you no longer wish to have twinned. Validate.
- Consult the list of twinnings.
The list of telephones twinned is displayed.
- Connect a mobile telephone that is twinned.
Select the telephone that you wish to connect. This access al-lows you to make a connection manually.
Call management
This menu is accessible during your calls, permitting you to :
- Swap a call if there is another call incoming.
- End a call.
- Be in Secret mode.
Note :
If you are in telephone conver-sation, you have access to this “ C o n fi g u r a t i o n” menu by means of a press on L or 7.
B L U E T O O T H®
Page 168 of 266
165
B L U E T O O T H®
Voice recognition
A short press on button 12 starts voice recognition for the telephone.
Voice recognition allows you to make a call to a number for which you have recorded a label on the mobile telephone that is twinned and connected.
Note :
It is possible to stop the call as long as the dialling has not com-menced, by means of a short press on button 12.
Notes :
- While you are on a call, the audio source currently being listened to is paused.
- Some ring tones on your mobile telephone may not be recognised by the Bluetooth system on your vehicle. A different ring tone will be chosen by the system.
Displays
A press on the “MODE” button displays the telephone information on the right of your screen.
A “Telephone” symbol appears on your display when you connect a mobile telephone.
A “Battery” symbol appears at the bottom of the display to indicate the range of the mobile telephone connected.
An “Envelope” symbol appears at the bottom of the display to indicate the presence of an unread SMS on the mobile telephone connected.
A “Sound track” symbol appears at the bottom of the display to indi-cate the presence of a message on the mobile telephone connected.
To swap a call
During a telephone conversation, the system is able to tell you of a second call incoming. To accept it, validate. To change from one call to the other, select this choice.
To end a call
This choice enables you to end a telephone conversation, for exam-ple if there is another call incoming.
Secret mode
Select this choice. This allows you not to be heard by the other person. To restore sound to the other person, select deactivation of Secret mode in the menu “Call Management”.
Note :
If you wish to transfer a call from the audio system to the mobile telephone (for example when lea-ving your vehicle), refer to the user instructions for the latter.
Page 198 of 266
VI
195
A n y r e p a i r o r a n y c h a n g e o f t y r e , o n a w h e e l fi t t e d w i t h a s e n s o r , should be carried out by a CITROËN dealer. A n y r e p a i r o r a n y c h a n g e o f t y r e , o n a w h e e l fi t t e d w i t h a s e n s o r , A n y r e p a i r o r a n y c h a n g e o f t y r e , o n a w h e e l fi t t e d w i t h a s e n s o r ,
The system may be affected from time to time by interference from radio transmissions on similar frequencies.
This function alerts you in the e v e n t o f a t y r e b e i n g d e fl a t e d o r punctured. For this purpose, sen-sors continuously monitor the con-dition of the vehicle’s wheels.
This system does not absolve the driver of the need to check the tyre pressures regularly.
T Y R E D E F L A T I O N D E T E C T I O N
The SERVICE warning lamp comes on and a ve-hicle outline is displayed, accompanied by a mes-sage and a sound signal. The wheel(s) concerned w i l l b e s h o w n fl a s h i n g o n t h e v e h i c l e outline. Check the tyre pressures as soon as possible.
D e fl a t i o n w a r n i n g
The STOP warning lamp comes on and a vehicle outline is displayed, ac-companied by a mes-sage and a sound signal. The wheel(s) concerned w i l l b e s h o w n fl a s h i n g o n t h e v e h i -cle outline. Stop the vehicle imme-diately, avoiding any violent actions on the steering wheel or brakes.
Puncture
Change the damaged wheel (whether punctured or substan- t i a l l y d e fl a t e d ) , h a v e t h e t y r e r e -paired as soon as possible, then check the tyre pressures as soon as you can after that.
The wheel affected will no longer be detectable by the alert system if it is in the boot or undergoing re-pair. The spare wheel is not moni-tored by the alert system.
The SERVICE warning lamp comes on and a vehicle outline is dis-played, accompanied by a message and a sound signal. The wheel(s) concerned will be shown as ab-sent on the vehicle outline. If you have not changed a wheel, this in-formation indicates a malfunction-ing of the system.
Consult the CITROËN network to have the defective sensor(s) re-placed.
Wheel not monitored
T h e d e fl a t i o n d e t e c t i o n s y s t e m i s a driving assistance function which does not relieve the driver from the responsibility to be vigilant.
This system does not absolve the driver of the need to check the tyre pressures on a regular basis ( s e e “ V e h i c l e i d e n t i fi c a t i o n » ) , t o ensure that the vehicle behaves as it should and to avoid prema-ture wear on the tyres, especially when the vehicle is being subject-ed to heavy loads or driven at high speeds.
Do not forget to check the tyre pressure on the spare wheel.